No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Configuration Guide - IP Unicast Routing

CloudEngine 8800, 7800, 6800, and 5800 V200R005C10

This document describes the configurations of IP Unicast Routing, including IP Routing, Static Route, RIP, RIPng, OSPF, OSPFv3, IPv4 IS-IS, IPv6 IS-IS, BGP, Routing Policy, and PBR.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Licensing Requirements and Limitations for Static Routes

Licensing Requirements and Limitations for Static Routes

Involved Network Elements

Other network elements are not required.

Licensing Requirements

Static routing is a basic feature of the CloudEngine 8800, 7800, 6800, and 5800 series switches and is not under license control.

Version Requirements

Table 2-2 Products and minimum version supporting static routes

Product

Minimum Version Required

CE8868EI

V200R005C10

CE8861EI

V200R005C10

CE8860EI

V100R006C00

CE8850-32CQ-EI

V200R002C50

CE8850-64CQ-EI

V200R005C00

CE7850EI

V100R003C00

CE7855EI

V200R001C00

CE6810EI

V100R003C00

CE6850EI

V100R001C00

CE6850-48S6Q-HI

V100R005C00

CE6850-48T6Q-HI/CE6850U-HI/CE6851HI

V100R005C10

CE6855HI

V200R001C00

CE6856HI

V200R002C50

CE6857EI

V200R005C10

CE6860EI

V200R002C50

CE6865EI

V200R005C00

CE6870-24S6CQ-EI/CE6870-48S6CQ-EI

V200R001C00

CE6870-48T6CQ-EI

V200R002C50

CE6875EI

V200R003C00

CE6880EI

V200R002C50

CE5880EI

V200R005C10

CE5810EI

V100R002C00

CE5850EI

V100R001C00

CE5850HI

V100R003C00

CE5855EI

V100R005C10

Feature Limitations

During an upgrade from V200R001C00SPC100 to a later version, if a static route's next hop is iterated to a remote VPN cross route and the next hop is a VXLAN tunnel, the static route is inactive in the source version but will become active in the target version. This modification will cause inconsistent traffic transmission paths before and after the upgrade. To prevent this issue, check whether a static route's next hop is iterated to a remote VPN cross route and the next hop is a VXLAN tunnel. If so, delete this static route.

The CE6810LI does not support IPv4 or IPv6 Layer 3 forwarding. After the IPv4 or IPv6 function is enabled on an interface of the CE6810LI, the configured IPv4 or IPv6 address can only be used to manage the switch.

In versions earlier than V200R002C50, the CE5855EI does not support IPv6. However, interfaces on the CE5855EI provide the IPv6 capability when the switch functions as a leaf switch in a super virtual fabric (SVF) system and the SVF forwarding mode is set to centralized or hybrid. In V200R002C50 and later versions, the CE5855EI supports IPv6.

Translation
Download
Updated: 2019-04-20

Document ID: EDOC1100074760

Views: 46498

Downloads: 58

Average rating:
This Document Applies to these Products
Related Version
Related Documents
Share
Previous Next