No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Configuration Guide - IP Unicast Routing

CloudEngine 8800, 7800, 6800, and 5800 V200R005C10

This document describes the configurations of IP Unicast Routing, including IP Routing, Static Route, RIP, RIPng, OSPF, OSPFv3, IPv4 IS-IS, IPv6 IS-IS, BGP, Routing Policy, and PBR.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Creating IPv6 Static Routes

Creating IPv6 Static Routes

Context

When creating IPv6 static routes, you can specify both the outbound interface and next hop. Alternatively, you can specify only the outbound interface or next hop based on the outbound interface type.
  • Specify the outbound interface for a P2P interface.

  • Specify the next hop for an NBMA interface.

  • Specify the outbound interface for a broadcast interface. If the next hop address is also specified, it does not need to be a link-local address.

If you specify the same preference for IPv6 static routes to the same destination, load balancing among these routes is implemented. If you specify different preferences for the IPv6 static routes, route backup among the routes is implemented.

If the destination IP address and mask are set to all 0s, an IPv6 static default route is configured. By default, no IPv6 static default route is configured.

NOTE:

Before configuring IPv6 routes with prefixes longer than 64 bits on a switch, run the assign forward ipv6 longer-mask resource command to specify the number of IPv6 addresses and routes with prefixes longer than 64 bits supported by the switch.

Procedure

  1. Run system-view

    The system view is displayed.

  2. Configure IPv6 static routes.
    • Run ipv6 route-static dest-ipv6-address prefix-length { interface-type interface-number [ nexthop-ipv6-address ] | vpn-instance vpn-instance-name nexthop-ipv6-address | nexthop-ipv6-address } [ preference preference | tag tag ] * [ bfd enable | track { bfd-session cfg-name | nqa admin-name test-name } ] [ inter-protocol-ecmp ][ description text ]

      An IPv6 static route is configured on the public network.

    • Run ipv6 route-static dest-ipv6-address prefix-length [ vpn-instance vpn-instance-name ] nexthop-ipv6-address [ preference preference | tag tag ] * inherit-cost [ inter-protocol-ecmp ] [ description text ]

      An IPv6 static route is configured on the public network.

    • Run ipv6 route-static dest-ipv6-address prefix-length vpn-instance vpn-instance-name [ preference preference | tag tag ] [ description text ]

      An IPv6 static route is configured on the public network.

    • Run ipv6 route-static vpn-instance vpn-source-name dest-ipv6-address prefix-length { interface-type interface-number [ nexthop-ipv6-address ] | vpn-instance vpn-destination-name nexthop-ipv6-address | nexthop-ipv6-address [ public ] } [ preference preference | tag tag ] * [ bfd enable | track { bfd-session cfg-name | nqa admin-name test-name } ] [ inter-protocol-ecmp ] [ description text ]

      An IPv6 static route is configured in a VPN instance.

    • Run ipv6 route-static vpn-instance vpn-source-name dest-ipv6-address prefix-length { vpn-instance vpn-destination-name | public } [ preference preference | tag tag ] [ description text ]

      An IPv6 static route is configured in a VPN instance.

    • Run ipv6 route-static vpn-instance vpn-source-name dest-ipv6-address prefix-length { vpn-instance vpn-destination-name dest-ipv6-address | dest-ipv6-address [ public ] } [ preference preference | tag tag ] * inherit-cost [ inter-protocol-ecmp ] [ description text ]

      An IPv6 static route is configured in a VPN instance.

  3. Run commit

    The configuration is committed.

Translation
Download
Updated: 2019-04-20

Document ID: EDOC1100074760

Views: 45018

Downloads: 58

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next