No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search


To have a better experience, please upgrade your IE browser.


Configuration Guide - Security

CloudEngine 8800, 7800, 6800, and 5800 V200R005C10

This document describes the configurations of Security, including ACL, local attack defense, MFF, attack defense, traffic suppression and storm control, ARP security, Port security, DHCP snooping, ND snooping, PPPoE+, IPSG, SAVI, separating the management plane from the service plane, security risks.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Configuring a Blacklist

Configuring a Blacklist


A blacklist is a group of users with particular characteristics. The device discards packets from users in the blacklist. You can apply an ACL to a blacklist.

On switches except the CE6870EI and CE6875EI, the following parameters cannot be specified for the ACL referenced by a blacklist. Otherwise, the blacklist is invalid.
  • Basic ACL: vpn-instance
  • Advanced ACL: vpn-instance

    The CE5880EI and CE6880EI do not support the icmp-type and igmp-type parameters in advanced ACLs.

  • Layer 2 ACL: 802.3
  • Basic ACL6: vpn-instance
  • Advanced ACL6: destination, dscp, and vpn-instance
On the CE6870EI and CE6875EI, only the following parameters can be specified for the ACL referenced by a blacklist. If other parameters are specified, the blacklist is invalid.
  • Basic ACL: source, time-range
  • Advanced ACL: protocol, source, time-range, ttl-expired, source-port, destination-port, igmp-type
  • Layer 2 ACL: source-mac, time-range, type, vlan
  • Basic ACL6: source, time-range
  • Advanced ACL6: protocol, source, time-range, source-port, icmp6-type, destination-port

For the CE6870EI running V200R002C50 and later versions, the blacklist no longer supports advanced ACLs with the source port number and TCP flag as matching rules. If a blacklist using the source port number or TCP flag as a matching rule is configured on a switch running a version earlier than V200R002C50, the blacklist becomes invalid after the switch is upgraded to V200R002C50 or a later version.


  1. Run system-view

    The system view is displayed.

  2. Run cpu-defend policy policy-name

    The attack defense policy view is displayed.

  3. Run blacklist blacklist-id acl { acl-number | ipv6 acl6-number } [ interface { interface-type interface-number1 [ to interface-type interface-number2 ] } &<1-8> ] [ vlan { vlan-id1 [ to vlan-id2 ] } &<1-8> ]

    A blacklist is created.

    A maximum of eight blacklists can be configured on the device.

    The ACL applied to a blacklist can be a basic ACL, an advanced ACL, an ARP-based ACL, a basic ACL6, an advanced ACL6, or a Layer 2 ACL. For details on how to create an ACL, see ACL Configuration.

    By default, no blacklist is configured on the device.


    During configuration restoration, the blacklists are restored in the ascending order of blacklist IDs (blacklist-id).

    For CE6870EI and CE6875EI, the ACL applied to a blacklist cannot be an ARP-based ACL.

  4. Run commit

    The configuration is committed.

Updated: 2019-04-20

Document ID: EDOC1100074765

Views: 28465

Downloads: 97

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Previous Next