No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Configuration Guide - Network Management and Monitoring

CloudEngine 12800 and 12800E V200R005C10

This document describes the configurations of Network Management and Monitoring, including SNMP, RMON, LLDP, NQA, Service Diagnosis, Mirroring, Packet Capture, sFlow, and NETCONF.
Rate and give feedback :
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Configuring NetStream Original Flow Statistics Export

Configuring NetStream Original Flow Statistics Export

Context

The original flow statistics can be exported only when a source IP address and at least one destination IP address and destination UDP port number have been specified for the exported packets.

Procedure

  1. Run the system-view command to enter the system view.
  2. Run the netstream export ipv6 source { ip-address | ipv6 ipv6-address } command to configure the source IP address for the exported packets carrying IPv6 original flow statistics.

    By default, the source IP address of the exported packets carrying IPv6 original flow statistics is not configured.

    If the source IP address is not specified, packets will not be exported. The source address of the exported packets carrying IPv6 original flow statistics can be either an IPv4 or IPv6 address. There must be a reachable route between the source IP address and destination IP address (NSC address). Two source IP addresses can be specified: one IPv4 address and one IPv6 address.

  3. Run the netstream export ipv6 host { ip-address | ipv6 ipv6-address } port-number [ vpn-instance vpn-instance-name ] command to configure the destination IP address and destination UDP port number for the exported packets carrying IPv6 original flow statistics.

    By default, the destination IP address and destination UDP port number of the exported packets carrying IPv6 original flow statistics are not configured.

    You can configure implement NSC backup by configuring two destination IP addresses. To configure a third destination IP address, run the undo netstream export ipv6 host command to delete an existing one first. Otherwise, the system will display a message indicating that the maximum number of IP addresses has been reached and the configuration will fail.

  4. (Optional) Run the assign netstream management-plane export rate-limit rate-limit [ slot slot-id ] command to limit the rate of NetStream packets sent from cards to the control plane, thereby limiting the rate of NetStream packets sent out by the control plane.

    By default, the rate of NetStream packets sent to the control plane is not limited.

    A card sends NetStream packets to the control plane only when the switch selects the management interface to send NetStream packets to the NetStream server. If the assign netstream management-plane export rate-limit rate-limit slot slot-id command has been executed to limit the rate of NetStream packets sent from a specified card to the control plane, you cannot run the assign netstream management-plane export rate-limit rate-limit command to limit the rate of NetStream packets sent from all cards to the control plane. If the assign netstream management-plane export rate-limit rate-limit command has been executed to limit the rate of NetStream packets sent from all cards to the control plane, you cannot run the assign netstream management-plane export rate-limit rate-limit slot slot-id command to limit the rate of NetStream packets sent from a specified card to the control plane.

    NOTE:

    The CE12800E does not support this command when configured with ED-E, EG-E, and EGA-E series cards, because only the service interfaces on the ED-E, EG-E, and EGA-E series cards can be used to export NetStream packets.

  5. (Optional) Run the netstream export ipv6 route disable command to remove IPv6 routing information from NetStream packets.

    By default, the NetStream packets exported by the device carry IPv6 routing information. This command can greatly improve switch performance. If the routing information is not required, run this command.

  6. (Optional) Run the netstream export packet-len ethernet-crc command to configure the IN_BYTES field value in NetStream packets to include the Ethernet header and CRC lengths.

    By default, the IN_BYTES field value in NetStream packets is the len field value in the IP packet header.

  7. Run the commit command to commit the configuration.
Translation
Download
Updated: 2019-04-20

Document ID: EDOC1100075344

Views: 20388

Downloads: 22

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next