No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Configuration Guide - Network Management and Monitoring

CloudEngine 12800 and 12800E V200R005C10

This document describes the configurations of Network Management and Monitoring, including SNMP, RMON, LLDP, NQA, Service Diagnosis, Mirroring, Packet Capture, sFlow, and NETCONF.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Configuring Versions for Exported Packets

Configuring Versions for Exported Packets

Context

The NDE exports NetStream flow statistics to the NSC. The version of exported packets must be the same as that configured on the NSC so that the NSC can parse the exported packets.

Exported packets in V8 have fixed format and are difficult to expand. The format of exported packets in V9 is defined in templates and is easy to expand. The statistics are exported flexibly.

Because of its advantages, V9 is supported by most NSCs. It is recommended that you set the version of exported packets carrying aggregation flow statistics to V9.

Procedure

  1. Run the system-view command to enter the system view.
  2. Run the netstream aggregation ip { as | as-tos | bgp-nexthop-tos | destination-prefix | destination-prefix-tos | index-tos | mpls-label | prefix | prefix-tos | protocol-port | protocol-port-tos | source-prefix | source-prefix-tos | source-index-tos | vlan-id } command to enter the NetStream aggregation view.

    The aggregation view must be the same as the aggregation view in Configuring NetStream Aggregation Flow Statistics Export.

    NOTE:

    The CE12800E does not support the mpls-label parameter, because the CE12800E does not support MPLS.

    The CE12800E does not support the as, as-tos, and bgp-nexthop-tos parameters when configured with ED-E, EG-E, and EGA-E series cards, because ED-E, EG-E, and EGA-E series cards do not support sampling of AS ang BGP next hop information.

  3. Run the export version { 8 | 9 } command to set the version of exported packets carrying aggregation flow statistics.

    For the aggregation modes as, as-tos, destination-prefix, destination-prefix-tos, prefix, prefix-tos, protocol-port, protocol-port-tos, source-prefix, and source-prefix-tos, the default version is V8. You can specify the version of exported packets.

    For the aggregation modes vlan-id, bgp-nexthop-tos, index-tos, mpls-label and source-index-tos the default version is fixed as V9, and these aggregation modes do not support the export version command.

  4. (Optional) Run the template timeout-rate timeout-interval command to set the interval at which the template for exporting aggregation flow statistics in V9 format is refreshed.

    By default, the template is refreshed every 1 minute.

    NOTE:

    If the default template update interval (30 minutes) is used in V200R001C00 or an earlier version, the interval is automatically changed to 1 minute after the version is upgraded to V200R002C50 or later.

    If the default template update interval (1 minute) is used in V200R002C50 or a later version, the interval is automatically changed to 30 minutes after the version is downgraded to V200R001C00 or an earlier version.

  5. Run the commit command to commit the configuration.
Translation
Download
Updated: 2019-04-20

Document ID: EDOC1100075344

Views: 20692

Downloads: 22

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next