No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Configuration Guide - IP Multicast

CloudEngine 8800, 7800, 6800, and 5800 V200R005C10

This document describes the configurations of IP multicast, including IP multicast basics, IGMP, MLD, PIM (IPv4), PIM (IPv6), MSDP, multicast VPN, multicast route management (IPv4), multicast route management (IPv6), IGMP snooping, MLD snooping, static multicast MAC address, multicast VLAN, multicast network management.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Monitoring the IPv6 Bidir-PIM Running Status

Monitoring the IPv6 Bidir-PIM Running Status

Context

During routine maintenance, you can run the following commands in any view to check the IPv6 PIM running status.

Procedure

  • Run the display pim ipv6 claimed-route [ ipv6-source-address ] command to check unicast routing information used for IPv6 PIM.
  • Run the display pim ipv6 bfd session [ interface interface-type interface-number | neighbor ipv6-link-local-address ] * command to check information about IPv6 PIM BFD sessions.
  • Run the display pim ipv6 bsr-info command to check BSR information.
  • Run the display pim ipv6 rp-info [ ipv6-group-address ] command to check RP information.
  • Run the display pim ipv6 interface [ interface-type interface-number | up | down ] [ verbose ] command to check IPv6 PIM information on interfaces.
  • Run the display pim ipv6 neighbor [ ipv6-link-local-address | interface interface-type interface-number | verbose ] * command to check IPv6 PIM neighbor information.
  • Run the display pim ipv6 control-message counters [ message-type { assert | hello | join-prune | bsr | backoff | offer | pass | win } | interface interface-type interface-number ] * command to check the number of IPv6 PIM control messages sent and received.
  • Run either of the following commands to check IPv6 PIM routing information:

    • display pim ipv6 routing-table [ ipv6-group-address [ mask mask-length ] ] { rpf-interface interface-type interface-number | mode bidir } * [ outgoing-interface { include | exclude | match } { interface-type interface-number | none } | flags flag-value | fsm ] * [ outgoing-interface-number [ number ] ]

    • display pim ipv6 routing-table brief [ ipv6-source-address [ mask mask-length ] | ipv6-group-address [ mask mask-length ] | incoming-interface { interface-type interface-number | register } ] *

  • Run the display pim ipv6 invalid-packet [ interface interface-type interface-number | message-type { assert | bsr | hello | join-prune | offer | backoff | win | pass } ] * command to check the statistics about invalid IPv6 PIM control messages received by an IPv6 PIM device.
  • Run the display pim ipv6 df-info [ rp rp-address | interface interface-type interface-number | verbose ]* command to check information about DFs on the device.
  • Run the display multicast ipv6 global { pim sm | bidir-pim | all } statistics command to check PIM entry restriction and statistics.
Translation
Download
Updated: 2019-04-20

Document ID: EDOC1100075361

Views: 20770

Downloads: 21

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next