No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search


To have a better experience, please upgrade your IE browser.


Configuration Guide - Virtualization

CloudEngine 8800, 7800, 6800, and 5800 V200R005C10

This document describes the configurations of virtualization, including stack and SVF.

Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Example for Configuring DAD in Direct Mode on Service Ports

Example for Configuring DAD in Direct Mode on Service Ports

Networking Requirements

As shown in Figure 1-34, SwitchA and SwitchB set up a stack. It is expected that stack split detection will be performed through idle ports in the stack.

Figure 1-34 DAD in direct mode on a service port

Configuration Roadmap

The configuration roadmap is as follows:
  1. Configure DAD in direct mode on 10GE1/1/0/5 and 10GE2/1/0/5.


  1. Configure DAD in direct mode on interfaces of the stack member switches.

    # Configure DAD in direct mode on 10GE1/0/5 and 10GE2/0/5.

    <HUAWEI> system-view
    [~HUAWEI] interface 10ge 1/0/5
    [~HUAWEI-10GE1/0/5] dual-active detect mode direct
    Warning: The interface will block common data packets, except BPDU packets. Continue? [Y/N]: y
    [*HUAWEI-10GE1/0/5] quit
    [*HUAWEI] interface 10ge 2/0/5
    [*HUAWEI-10GE2/0/5] dual-active detect mode direct
    Warning: The interface will block common data packets, except BPDU packets. Continue? [Y/N]: y
    [*HUAWEI-10GE2/0/5] commit
    [~HUAWEI-10GE2/0/5] return

  2. Verify the configuration.

    # Check the DAD configuration on the stack.

    <HUAWEI> display dual-active
    Stack domainID: 10
    Dual-active status: Normal
    Dual-active detect mode: Direct
    Dual-active detect configuration of MEth: Disable
    Dual-active direct detect interfaces configured:
     10GE1/0/5        up  (Physical)  up  (Protocol)  10   (PeerDomain)
     10GE2/0/5        up  (Physical)  up  (Protocol)  10   (PeerDomain)
    Dual-active relay detect interfaces configured:
    Excluded ports(configurable):
    Excluded ports(can not be configured):

  3. Verify the DAD function.

    After the DAD function is configured:
    • If a stack split occurs, the alarm "DAD_1. hwDadConflictDetect" is generated.
    • If the stack recovers from a split, the alarm "DAD_1. hwDadConflictResume" is generated.
    If no service is configured in the stack, simulate a stack split situation to check whether the DAD function is configured successfully.

    Do not trigger a stack split when services are running on the stack. Otherwise, services are affected.

    1. Trigger a stack split by disabling all ports with stack cables connected or removing all stack cables.

    2. Run the display stack command to check whether the number of stack member switches reduces. If so, the stack has split.

    3. Run the display trapbuffer command to check whether there are DAD alarms.
      <HUAWEI> display trapbuffer
      Aug 15 2016 14:32:35 HUAWEI %%01DAD/1/hwDadConflictDetect(t):CID=0x807f0419-OID=;Dual-active scenario is detected.
    4. The preceding operations verify that the DAD function has been configured successfully.

    5. Restore the stack by enabling all ports used for stack connections or reconnecting stack cables so that the stack can be set up again.

Configuration Files

  • Stack configuration file

    interface 10GE1/0/5
     dual-active detect mode direct
    interface 10GE2/0/5
     dual-active detect mode direct
Updated: 2020-01-07

Document ID: EDOC1100075367

Views: 12662

Downloads: 80

Average rating:
This Document Applies to these Products

Related Version

Related Documents

Previous Next