No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

FusionStorage 8.0.0 Block Storage Hardware Installation Guide 06

Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Checking Before Unpacking Equipment

Checking Before Unpacking Equipment

After a project starts, the project supervisor must unpack and check the devices with the customer representative together.

Prerequisites

  • The goods are delivered to the project field.
  • Both the project supervisor and customer representative are present.

Context

  • The Packing List is contained in a bag, which is then stuck onto the outside of the carton.
  • When the goods arrive on site, check them according to the Packing List.
  • If the Packing List states some deficient goods, notify the manufacturer local office for subsequent handling and sign the Packing List. If short, wrong, or excessive shipment of goods occurs or goods are damaged, the two parties must sign the Memo for Unpacking and Checking Goods and Packing List. Meanwhile, the project supervisor must fill out the Goods Problem Feedback Form, submit it to the manufacturer local office within three days, and maintain the goods (including internal and external packages) intact for future investigation.
  • If the goods are in good condition, the two parties sign the Packing List, and then the goods are handed over to the customer.

Procedure

  1. Check before unpacking the goods.

    After a project starts, the project supervisor should check the goods with the customer representatives before unpacking the goods. For details about the check method, see Table 5-1.

    Table 5-1 Checklist before unpacking goods

    Packing Case Type

    Check Whether

    Wooden crate

    The wooden crate surface is damaged in any form, for example, scratched, cracked, or concave.

    The tongues or latches are properly locked, or the wooden crate is already open.

    The feet of the wooden crate are disconnected, improperly connected, or damaged.

    The wooden crate is corrosive or mildewy.

    The wooden crate is dirty or soaked.

    The void label on the wooden crate is torn (ignoring minor wear), or the lead seal is open.

    Carton

    The carton surface is damaged in any forms, for example, scratched or cracked.

    The carton is dirty or soaked.

    The carton is distorted in any forms, for example, convex, concave, or creased, especially its 8 angles and 12 edges.

    The sealing adhesive tape is torn.

    The carton has void labels of two or more layers, and the void labels are torn.

    Stack board package

    The stacking cartons of the same specifications are distorted, convex, or concave.

    Packing straps are broken.

    The soleplate of the wooden crate is cracked, the feet of the wooden crate tilt obviously, or a wooden foot is absent.

    Paper edge protectors have squeezed the carton, and are dirty or damaged.

    Shipment label

    Characters on the shipment label are clear, and the shipment label curls up, falls off, or is smeared.

    Characters on monitoring labels (if any) are clear.

    Tilt indicator

    It is normal when the tilt indicator is in gray. When the tilt angle is greater than 80°, the tilt indicator is in red.

    It is normal when the blue powder is below the horizontal line. When the tilt angle is greater than 85°, the blue powder is above the horizontal line and enters the arrow area.

    It is normal when there are four balls on either side. When the tilt angle is greater than 85°, the number of balls on either side changes.

    Shockwatch label

    It is normal when the shockwatch label is in gray, and it is abnormal when the shockwatch label is in red.

    Others

    There are damaged packages that cause materials to be exposed.

  2. Based on the check result, take the following measures:

    • If the number of the goods is correct and the appearances of the packing boxes are intact, unpack to check the goods.
    • If the number of the goods is incorrect or the carton is severely damaged or soaked, do not open the carton and notify the manufacturer local office.

    To protect the devices and find out the reasons, move the devices out of the unpacked packages and store them indoors properly. Take pictures of the device storage environment, rusty or eroded devices, packages, and packing materials, and archive the pictures. Store the unpacked packages and packing materials properly.

Download
Updated: 2019-11-14

Document ID: EDOC1100081415

Views: 7006

Downloads: 15

Average rating:
This Document Applies to these Products
Related Version
Related Documents
Share
Previous Next