Network Device List

TaiShan Server BIOS Parameter Reference (Kunpeng 920 Processor) 21

Rate and give feedback:

Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).

Network Device List

You can set parameters for the PCIe NIC on the Network Device List screen. Figure 5-42 shows the Network Device List screen. Table 5-31 describes the parameters.

The configuration screen varies according to the PCIe NIC. The following screen is an example.
For details about the PXE function of the LOM, see the LOM Configuration menu.

Figure 5-42 Network Device List screen

Table 5-31 Parameters on the Network Device List screen

Parameter	Description
MAC:AC:8D:34:21:2B:60	Sets parameters for this NIC on the specified port.
MAC:AC:8D:34:21:2B:61	Sets parameters for this NIC on the specified port.
MAC:00:02:03:04:05:06	Sets parameters for this NIC on the specified port.
MAC:00:02:03:04:05:07	Sets parameters for this NIC on the specified port.
MAC:00:02:03:04:05:08	Sets parameters for this NIC on the specified port.
MAC:00:02:03:04:05:09	Sets parameters for this NIC on the specified port.
MAC:00:15:45:D9:00:D8	Sets parameters for this NIC on the specified port.
MAC:00:15:45:D9:02:50	Sets parameters for this NIC on the specified port.
MAC:00:15:45:D9:00:84	Sets parameters for this NIC on the specified port.
MAC:00:15:45:D9:00:C9	Sets parameters for this NIC on the specified port.

MAC:AC:8D:34:21:2B:60 is used as an example to describe the NIC configuration screen. Figure 5-43 shows the Network Device MAC:AC:8D:34:21:2B:60 screen. For parameter details, see Table 5-32.

When the PXE Boot Capability parameter in the LOM Configuration menu is set to an HTTPS option, the HTTP Boot Configuration menu is displayed on the Network Device screen, as shown in Figure 5-44.

Figure 5-43 Network Device screen (1)

Figure 5-44 Network Device screen (2)

Table 5-32 Parameters on the Network Device screen

Parameter	Description
Huawei (R) Intelligent Network Interface Card	Sets NIC parameters. NOTE: If no NIC is detected, this parameter is not displayed.
IPv4 Network Configuration	Sets the IPv4 network.
IPv6 Network Configuration	Sets the IPv6 network.
HTTP Boot Configuration	Provides access to HTTP authentication configuration. NOTE: When PXE Boot Capability in the LOM Configuration menu is set to an HTTPS option, this menu is displayed on the Network Device screen.

Figure 5-45 shows the Huawei (R) Intelligent Network Interface Card screen. For parameter details, see Table 5-33.

Figure 5-45 Main Configuration Page

Table 5-33 Parameters on the Main Configuration Page

Parameter	Description	Default Value
Device Name	Indicates the name of an NIC.	-
PXE	Specifies whether to enable the PXE function. The options are as follows: DISABLE ENABLE	ENABLE
PXE VLAN	Specifies whether to enable the PXE VLAN function. The options are as follows: DISABLE ENABLE	DISABLE
Bandwidth (%)	Specifies the bandwidth whose value ranges from 1 to 100.	100
Work Mode	Specifies the working mode of the NIC. The options are as follows: Basic NIC Mode OVS Offload Mode	Basic NIC Mode
GE Mode	Enables or disables the GE mode of the network port. The options are as follows: DISABLE ENABLE	DISABLE
Adaptive Link	Enables or disables link adaptation. The options are as follows: OFF ON	OFF
Auto Negotiation	Specifies whether to enable the auto-negotiation function of the network port. The options are as follows: ON OFF	ON
SRIOV Control	Specifies whether to enable the SRIOV Control function. The options are as follows: ON OFF	ON
Reset to Factory Default	Restores factory defaults.	-

Figure 5-46 shows the IPv4 Network Configuration screen. Table 5-34 describes the parameters.

Figure 5-46 IPv4 Network Configuration screen

Table 5-34 Parameters on the IPv4 Network Configuration screen

Parameter	Description
Configured	Indicates whether the network address is configured successfully. The value is displayed in a checkbox and is not selected by default. Press Enter to switch the status. X indicates that this parameter is enabled.
Enable DHCP	Configures whether to enable DHCP. The value is displayed in a checkbox and is not selected by default. Press Enter to switch the status. X indicates that this parameter is enabled. NOTE: This parameter is displayed only when Configured is selected. If the DHCP service needs to be enabled, the peer end of the network port must be connected to the DHCP server. The DHCP service can be enabled only after the IP address is obtained dynamically. If DHCP fails to be enabled, the settings of Configured and Enable DHCP are not saved.
Local IP Address	Sets the local IPv4 address. NOTE: This parameter is displayed only when Configured is selected and Enable DHCP is not selected.
Local NetMask	Specifies the local IPv4 subnet mask. NOTE: This parameter is displayed only when Configured is selected and Enable DHCP is not selected.
Local Gateway	Sets the local IPv4 gateway. NOTE: This parameter is displayed only when Configured is selected and Enable DHCP is not selected.
Local DNS Servers	Sets the local DNS. NOTE: This parameter is displayed only when Configured is selected and Enable DHCP is not selected.
Save Changes and Exit	Saves changes and exits.

Figure 5-47 shows the IPv6 Network Configuration screen. Table 5-35 describes the parameters.

Figure 5-47 IPv6 Network Configuration screen

Table 5-35 Parameters on the IPv6 Network Configuration screen

Parameter	Description
Enter Configuration Menu	Provides access to IPv6 network configuration.

Figure 5-48 shows the Enter Configuration Menu screen. Table 5-36 describes the parameters.

Figure 5-48 IPv6 Current Setting screen

Table 5-36 Parameters on the IPv6 Current Setting screen

Parameter	Description	Default Value
Interface Name	Displays the interface name.	-
Interface Type	Displays the interface type.	-
MAC address	Displays the current MAC address.	-
Host addresses	Displays the address of the current host.	-
Route Table	Displays the current routing table.	-
Gateway addresses	Displays the current gateway address.	-
DNS addresses	Displays the DNS server list.	-
Interface ID	Sets the 64-bit standby interface ID of the device. Use colons (:) to separate character strings.	-
DAD Transmit Count	Specifies the number of consecutive neighbor solicitation (NS) messages sent when duplicate address detection is performed on a temporary address. 0 indicates that duplicate address detection is not performed.	0
Policy	Selects a policy. The options are as follows: automatic manual	automatic NOTE: This parameter is automatically set to manual each time the BIOS screen is displayed after the server is restarted.
Advanced Configuration	Provides access to advanced configuration. NOTE: This parameter is displayed only when Policy is set to manual.	-
Save Changes and Exit	Saves the changes and exits.	-

Figure 5-49 shows the Advanced Configuration screen. Table 5-37 describes the parameters.

Figure 5-49 Advanced Configuration screen

Table 5-37 Parameters on the Advanced Configuration screen

Parameter	Description
New IPv6 address	Sets a new IPv6 address.
New Gateway addresses	Sets a new gateway address.
New DNS addresses	Sets a new DNS address.
Commit Changes and Exit	Submits changes and exits.
Discard Changes and Exit	Discards changes and exits.

Figure 5-50 shows the HTTP Boot Configuration screen. Table 5-38 describes the parameters.

When PXE Boot Capability in the LOM Configuration menu is set to an HTTPS option, this menu is displayed on the Network Device screen.

Figure 5-50 HTTP Boot Configuration screen

Table 5-38 Parameters on the HTTP Boot Configuration screen

Parameter	Description	Default Value
Input the description	Indicates the user-defined name for starting HTTP.	-
Internet Protocol	Indicates the HTTP startup protocol. The options are as follows: IP4 IP6	IP4
Boot URI	Sets the path for starting the HTTP. NOTE: If this path is set, the Exit screen displays boot options started from this path.	-

Parameter

Description

Default Value

Input the description

Indicates the user-defined name for starting HTTP.

Internet Protocol

Indicates the HTTP startup protocol. The options are as follows:

IP4

Boot URI

Sets the path for starting the HTTP.

NOTE:

If this path is set, the Exit screen displays boot options started from this path.

Translation

简体中文

Download

Updated: 2023-04-27

Document ID: EDOC1100088647

Downloads: 456

Average rating:

This Document Applies to these Products

Related Version

Digital Signature File

Digital Signature Authentication Mode

Enterprise

Huawei Cloud

Carrier

Consumer

Corporate

Related Version

Related Documents

Digital Signature File