LST7G48SX6S0-48-Port GE SFP Interface Card (X6S, SFP)
Version Mapping
Card Name |
S12700E Chassis |
|---|---|
LST7G48SX6S0 |
Supported in V200R019C00 and later versions |
Introduction
The LST7G48SX6S0 provides high performance, large entry sizes, and a large buffer for data switching. This card is highly integrated and has a large port density.
The LST7G48SX6S0 can be installed in:
- Slots 01 to 04 in an S12700E-4 chassis.
- Slots 01 to 08 in an S12700E-8 chassis.
- Slots 01 to 12 in an S12700E-12 chassis.
Functions
- Communicates with the MPU and works under the control of the MPU.
- Searches for routes and destination addresses of data packets for forwarding.
- Forwards data packets.
Function |
Description |
|---|---|
Basic functions |
Provides forty-eight GE optical ports for data access and switching. |
Distributed forwarding |
Performs concurrent data forwarding using a distributed data plane. |
Hot swapping |
Supported |
Indicators and Ports
Number |
Indicator |
Color |
Description |
|---|---|---|---|
1 |
ACT indicator of a lower optical port |
Yellow |
Blinking: The port is transmitting and receiving data. |
2 |
ACT indicator of an upper optical port |
||
3 |
LINK indicator of a lower optical port |
Green |
Steady on: A link has been established on the port. |
4 |
LINK indicator of an upper optical port |
||
5 |
RUN/ALM: running status indicator |
Green |
Steady on: The card is powered on. If the indicator is steady green for no more than 30 seconds, the CPU is being started. If the indicator is steady green for more than 30 seconds, the software is not running. Slow blinking: The card software is running properly. Fast blinking: The card software is starting. |
Red |
Steady on: The card has failed and the fault requires manual intervention. |
||
Yellow |
Steady on: The card is powered off. (For example, the card has been forcibly powered off using the power off command or is about to start.) |
1 |
Forty-eight 1000BASE-X ports |
1000BASE-X port
Table 6-54 describes the attributes of a 1000BASE-X port with an optical module installed.
Attribute |
Description |
|---|---|
Connector type |
SFP |
Optical port attributes |
Depend on the SFP optical module used. For optical modules supported by the LST7G48SX6S0 and their attributes, see GE eSFP Optical Modules, GE-CWDM eSFP Optical Modules, and GE-DWDM eSFP Optical Modules. |
Standards compliance |
IEEE 802.3z |
Frame format |
Ethernet_II, Ethernet_SAP, Ethernet_SNAP |
Network protocol |
IP |
Table 6-55 describes the attributes of a 1000BASE-X port with a copper module installed.
Attribute |
Description |
|---|---|
Connector type |
SFP |
Optical port attributes |
Depend on the SFP copper module used. For details on the copper modules supported by the cards and attributes of the copper modules, see GE SFP Copper Modules (100 Mbit/s and 1000 Mbit/s rates). |
Standards compliance |
IEEE 802.3ab |
Frame format |
Ethernet_II, Ethernet_SAP, Ethernet_SNAP |
Network protocol |
IP |
Specifications
Item |
Description |
|---|---|
Physical specifications |
|
Ordering Information
Card ordering information is subject to updates with product version upgrades. The ordering information provided in this manual is for reference only. To obtain the latest ordering information, contact Huawei switch distributors or Huawei local office.
Part Number |
Card Name |
Card Model |
|---|---|---|
03033DMP |
48-Port GE SFP Interface Card (X6S, SFP) |
LST7G48SX6S0 |
