Example for Configuring the Passenger Flow Analysis Function

Fat AP and Cloud AP V200R019C00 Web-based Configuration Guide

This document describes how to configure and maintain devices through the web NMS client.

Rate and give feedback:

Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).

Example for Configuring the Passenger Flow Analysis Function

Networking Requirements

On the network of a shopping mall shown in Figure 3-13, a Fat AP interconnects with a location server through a switch. It is required that the Fat AP provide Wi-Fi access for STAs while implementing the passenger flow analysis function with the help of the location server.

Figure 3-13 Configuring the passenger flow analysis function

Data preparation

Item	Data
Service VLAN for STAs	VLAN 101
DHCP server	The AP functions as a DHCP server to assign IP addresses to STAs.
IP address pool for STAs	10.23.101.2-10.23.101.254/24
SSID profile	Name: wlan-net SSID name: wlan-net
Security profile	Name: wlan-net Security policy: WPA-WPA2+PSK+AES Password: a1234567
VAP profile	Name: wlan-net Service VLAN: VLAN 101 Referenced profile: SSID profile wlan-net and security profile wlan-net
Air scan profile	Name: wlan-air-scan Probe channel set: calibration channels
2G radio profile	Name: default Referenced profile: air scan profile wlan-air-scan
5G radio profile	Name: default Referenced profile: air scan profile wlan-air-scan
Location profile	Name: wlan-location Destination IP address/Port number used by the AP to report channel scan information: 10.23.100.2/32180

Configuration Roadmap

Configure basic WLAN services so that users can connect to the internal network through the WLAN.
Configure the passenger flow analysis function so that APs can periodically scan channels to collect radio signals and report the collected information to the location server.

Procedure

Configure the location server (details are not provided here).
Configure basic WLAN services based on data planning. For details, see Example for Configuring Fat AP Layer 2 Networking.
Configure the WLAN air scan function.
1. Create an air scan profile.
  # Choose Configuration > WLAN Service > Profile > Radio Management > Air Scan Profile. The Air Scan Profile List page is displayed.
  
  # Click Create to create the air scan profile wlan-air-scan and click OK.
  
  # Set Probe channel set to Country code channels.
  
  # Click Apply.
2. Configure the 2G radio profile and bind the air scan profile to the 2G radio profile.
  # Choose Configuration > WLAN Service > Profile > Radio Management > 2G Radio Profile.
  
  # Click next to the 2G radio profile default in Profile Management. The profiles referenced by the 2G radio profile are displayed. Click Air Scan Profile.
  
  # Set Air Scan Profile to wlan-air-scan.
  
  # Click Apply.
3. Configure the 5G radio profile and bind the air scan profile to the 5G radio profile.
  # Choose Configuration > WLAN Service > Profile > Radio Management > 5G Radio Profile.
  
  # Click next to the 5G radio profile default in Profile Management. The profiles referenced by the 5G radio profile are displayed. Click Air Scan Profile.
  
  # Set Air Scan Profile to wlan-air-scan.
  
  # Click Apply.
Configure the passenger flow analysis function.
1. Create a location profile.
  # Choose Configuration > WLAN Service > Profile > WLAN Location > WLAN Location Profile. The WLAN Location Profile List page is displayed.
  
  # Click Create to create the location profile wlan-location and click OK.
  
  # Configure terminal location parameters.
  
  # Click Apply.
2. Apply the location profile to radio 0.
  # Choose Configuration > WLAN Service > WLAN Config > Radio0 > WLAN Location > WLAN Location Profile, select wlan-location, and click Apply.
3. Apply the location profile to radio 1.
  # Choose Configuration > WLAN Service > WLAN Config > Radio1 > WLAN Location > WLAN Location Profile, select wlan-location, and click Apply.
Verify the configuration.
Check and collect statistics about STA online duration through the location server.

Translation

简体中文

Download

Updated: 2021-11-19

Document ID: EDOC1100096316

Downloads: 4089

Average rating:

This Document Applies to these Products

Related Version

Digital Signature File

Digital Signature Authentication Mode

Enterprise

Huawei Cloud

Carrier

Consumer

Corporate