RTN510 V100R019C00 and Later Service Configuration and Maintenance Guide 06

Rate and give feedback:

Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).

About This Document

Related Versions

The following table lists the product versions related to this document.

RTN510	NMS
V10R021C00	iMaster NCE: V100R021C00 eSight: 21.0.0
V10R020C10	iMaster NCE: V100R020C10 eSight: 20.1.0
V10R020C00	iMaster NCE: V100R019C00 eSight: 20.0.0
V100R019C10	iMaster NCE: V100R019C00 eSight: V300R010C00SPC630
V100R019C00	iManager U2000: V200R018C60 eSight: V300R010C00SPC501

Intended Audience

This document provides the guidelines to maintaining the RTN510. It also describes the alarms and performance events that are required for troubleshooting during the maintenance.

This document is intended for:

Network planning engineer
Data configuration engineer
System maintenance engineer

Symbol Conventions

The symbols that may be found in this document are defined as follows.

Symbol	Description
	Indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury.
	Indicates a hazard with a medium level of risk which, if not avoided, could result in death or serious injury.
	Indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury.
	Indicates a potentially hazardous situation which, if not avoided, could result in equipment damage, data loss, performance deterioration, or unanticipated results. NOTICE is used to address practices not related to personal injury.
	Supplements the important information in the main text. NOTE is used to address information not related to personal injury, equipment damage, and environment deterioration.

Command Conventions

The command conventions that may be found in this document are defined as follows.

Convention	Description
Boldface	The keywords of a command line are in boldface.
Italic	Command arguments are in italics.
[ ]	Items (keywords or arguments) in brackets [ ] are optional.
{ x \| y \| ... }	Optional items are grouped in braces and separated by vertical bars. One item is selected.
[ x \| y \| ... ]	Optional items are grouped in brackets and separated by vertical bars. One item is selected or no item is selected.
{ x \| y \| ... }^*	Optional items are grouped in braces and separated by vertical bars. A minimum of one item or a maximum of all items can be selected.
[ x \| y \| ... ]^*	Optional items are grouped in brackets and separated by vertical bars. Several items or no item can be selected.

GUI Conventions

The GUI conventions that may be found in this document are defined as follows.

Convention	Description
Boldface	Buttons, menus, parameters, tabs, window, and dialog titles are in boldface. For example, click OK.
>	Multi-level menus are in boldface and separated by the ">" signs. For example, choose File > Create > Folder.

Change History

Changes between document issues are cumulative. The latest document issue contains all the changes made in earlier issues.

Issue 06 (2021-06-30)

Compared with Issue 05, Issue 06 incorporates the following changes.

Topic	Description
Entire document	Updated the eSight screenshots.
Entire document	Updated the screenshots showing operations on the web-based NMS.
Configuration Example	Updated the QoS configuration operations.
Configuration Example	Updated the Ethernet OAM configuration operations.
Configuring LLDP	Updated the LLDP configuration operations.
Configuring VLAN Free for the DCN	Added the description of configuring VLAN Free for the DCN on the AP, RT, and RT II.
Browsing Historical RMON Performance Events	Added the operations of browsing historical RMON performance data on the web-based NMS and eSight.
RT II	Added the MW_CFG_MISMATCH alarm for the RT II.
MW_CFG_MISMATCH, LOOP_ALM, RADIO_RSL_HIGH, RADIO_RSL_LOW	Modified the alarm parameters.

Issue 05 (2020-12-31)

Compared with Issue 04, Issue 05 incorporates the following changes.

Topic	Description
Synchronizing Alarms	Added the operation of synchronizing device alarms on the eSight.
Creating a Performance Monitoring Task	Added the operation of creating a performance monitoring task on the eSight.
Browsing Current Alarms	Added the operation on the eSight.
Browsing Historical Performance Events	Added the operation on the eSight.
Uploading a Certificate	Add the operation of uploading a certificate.
Managing WLAN Configurations	Add the operation of managing WLAN configurations.
Configuring IEEE 802.1d Bridge-based E-LAN Services	The AP supports 802.1d bridge-based E-LAN services.
Configuring IEEE 802.1q Bridge-based E-LAN Services	The AP supports 802.1q bridge-based E-LAN services.
Configuring 802.1ad Bridge-based E-LAN Services	The AP supports 802.1ad bridge-based E-LAN services.
Configuring H-Aware-based E-LAN Services	The AP supports H-Aware-based E-LAN services.

Issue 04 (2020-09-20)

Compared with Issue 03, Issue 04 incorporates the following changes.

Topic	Description
Using SNMPv2c	Added operations for configuring SNMPv2c in V100R020C00 and later versions.

Issue 03 (2020-06-30)

Compared with V100R019C00, V100R020C00 incorporates the following changes.

Topic	Description
Using SNMPv3 for Connection to the AP/RT, Using SNMPv3 for Connection to the RT II	Added operations for configuring SNMPv3 in V100R020C00 and later versions.
Alarm Reference	Added support for the MW_CFG_MISMATCH and RTC_FAIL alarms.
Performance Events and Handling Procedures	The RT II supports BDENVRHMAX, BDENVRHMIN, BDENVRHCUR performance.

Issue 02 (2020-04-20)

Compared with V100R019C00, V100R019C10 incorporates the following changes.

Topic	Description
Performing Health Check and Modifying Configurations	Scripts are supported for configuring services in a batch.
Configuring Ethernet Services	The RT II supports E-Line services.
Alarm Reference	The RT II supports ETH_LINK_DOWN, LOOP_ALM, MAC_FCS_EXC, MAC_EXT_EXC, SSL_CERT_DAMAGED, SSL_CERT_TO_EXPIRE, SSL_CERT_NOENC, DBMS_ERROR, and NEIP_CONFU. SION, DHCP_FREE_IP_USE_UP, and NESOFT_MM.
RMON Event Reference	The RT II supports RXPAUSE, TXPAUSE, RXBRDCAST_RATIO, and TXBRDCAST_RATIO.

Issue 01 (2019-07-30)

This issue is the first release for the product version V100R019C00.

Translation

简体中文

Download

Updated: 2021-08-04

Document ID: EDOC1100103249

Downloads: 288

Average rating:

This Document Applies to these Products

Related Version

Digital Signature File

Digital Signature Authentication Mode