No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

SmartLogger3000 User Manual

This document describes the SmartLogger3000 and SmartModule1000A01 in terms of installation, electrical connections, system operation, maintenance, and troubleshooting. BOM number: 02312SCU, 02312SCU-001, 02312SCU-002, 02312SCU-003, 02312SCU-004, 02312SCU-005, 02312SCU-006, 02312SCU-007, 02312SCU-008, 02312SCU-009, 02312SCU-010, 02312SGF, 02312SGG, 02312SGK and 02312SGJ.

Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
How Do I Set FTP Parameters?

How Do I Set FTP Parameters?

Context

The FTP function is used to access a third-party NMS. The SmartLogger can report the configuration information and running data of the managed PV plant system through FTP. A third-party NMS can access Huawei devices after being configured.

FTP is a universal standard protocol without any security authentication mechanism. Data transmitted by FTP is not encrypted. To reduce network security risks, the IP address of the connected third-party FTP server is left blank by default. This protocol can transmit the running data of PV plants, which may cause user data breach. Therefore, exercise caution when using this protocol. Users are liable for any loss caused by the enabling of the FTP protocol (non-secure protocol). Users are advised to take measures at the PV plant level to reduce security risks, or use Huawei management system to mitigate the risks.

Procedure

  1. Set FTP parameters and click Submit.

    Figure 8-3 Setting FTP parameters

    Parameter

    Description

    FTP server

    Set this parameter to the domain name or IP address of the FTP server.

    User name

    Set this parameter to the user name for logging in to the FTP server.

    Password

    Set this parameter to the password for logging in to the FTP server.

    Remote directory

    After you set this parameter, a subdirectory of the same name is created in the default data upload directory (specified by the FTP server).

    Data export

    Specifies whether data can be reported.

    File format

    Format 1, Format 2, Format 3, and Format 4 are supported.

    NOTE:

    Format 2 has two more information points than Format 1: E-Day (current-day energy yield) and E-Total (total energy yield). Format 3 has more information points than Format 1 and Format 2: power meter, PID module, user-defined device, and SmartLogger data. Format 4 has more information points than Format 3: active and reactive power of power meters.

    File name

    Set this parameter to the format of the file name.

    Time format

    Set this parameter to the time format.

    Export mode

    The value can be Cyclic or Fixed time.

    • Cyclic: Periodically reports data. Export interval specifies the period for reporting data. File mode specifies whether all data or only the incremental data of a day is reported each time.
    • Fixed time: Reports data at a specified time. Fixed time specifies the time for reporting data.

    You can click Start report test to check whether the SmartLogger can report data to the FTP server.

Troubleshooting

If the error code is not listed in the following table, provide SmartLogger run logs and contact Huawei technical support.

Error Code

Troubleshooting Suggestion

Error Code

Troubleshooting Suggestion

0x1002

Configure the FTP server address.

0x1003

  1. Check whether the DNS server address is correctly configured.
  2. Check whether the domain name of the third-party FTP server is correctly configured.

0x1004

Configure the user name of the FTP account.

0x1005

Configure the user name of the FTP account.

0x3001

  1. Check whether the FTP server address is correctly configured.
  2. Check whether the third-party FTP server is working properly.

0x3002

  1. Check whether the user name of the FTP account is correctly configured.
  2. Check whether the password of the FTP account is correctly configured.

0x3007

Check whether the third-party FTP server allows the client to upload data.

0x3008

Ensure that the SmartLogger data upload directory exists on the third-party FTP server.

Other Codes

Provide SmartLogger run logs and contact Huawei technical support.

N/A

N/A

Translation
Download
Updated: 2020-01-17

Document ID: EDOC1100108365

Views: 6526

Downloads: 1164

Average rating:
This Document Applies to these Products

Related Version

Related Documents

Share
Previous Next