No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

SmartLogger3000 User Manual

This document describes the SmartLogger3000 and SmartModule1000A01 in terms of installation, electrical connections, system operation, maintenance, and troubleshooting. BOM number: 02312SCU, 02312SCU-001, 02312SCU-002, 02312SCU-003, 02312SCU-004, 02312SCU-005, 02312SCU-006, 02312SCU-007, 02312SCU-008, 02312SCU-009, 02312SCU-010, 02312SGF, 02312SGG, 02312SGK and 02312SGJ.

Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Setting IEC103 Device Parameters

Setting IEC103 Device Parameters

Description

An IEC103 device supports two data transmission modes:

  • Transparent transmission mode: When connecting to the management system, the SmartLogger transparently transmits the IEC103 device information to the management system. The SmartLogger does not parse the IEC103 device data.
  • Parsing mode: The IEC103 device is connected to the SmartLogger, and the SmartLogger parses the IEC103 device data.

Transparent Transmission Mode

  1. Set IEC103 parameters and click Submit.

    Figure 6-32 Setting IEC103 parameters

    Parameter

    Description

    IEC103 port No.

    Set this parameter based on the COM port connected to the device.

    IEC103 address

    Set this parameter to the IEC103 device address.

    IEC103 IP

    Set this parameter to the IP address of the management system.

  2. Choose Settings > Other Parameters and check that Data forwarding is set to Enable.

    • If Data forwarding is set to Enable, the SmartLogger transparently transmits information about unconnected devices to the management system without parsing device data.
    • If Data forwarding is set to Disable, the SmartLogger does not transmit information about unconnected devices to the management system.

Parsing Mode

The SmartLogger can connect to third-party devices that support IEC103, such as the relay protection or monitoring device like the transformer substation. The protocol information points vary depending on vendors. Therefore, you need to obtain a protocol information file in .cfg format from Huawei and import the file into the SmartLogger for successfully connecting to a custom device.

The supported device types are IEC103 device 1 to IEC103 device 5. The corresponding configuration file names are iec103_equip_custom_1.cfg to iec103_equip_custom_5.cfg. Multiple devices of the same type can be connected.

  1. Configure a protocol information point file in .cfg format and import the file to the SmartLogger.

    Figure 6-33 Importing configuration

  2. Set access parameters and click Add Devices.

    Figure 6-34 Setting access parameters

    Parameter

    Description

    Device Type

    The value can be IEC103 Device 1 to IEC103 Device 5.

    Select a value based on the configuration file. For example, if iec103_equip_custom_1.cfg needs to be imported, select IEC103 Device 1.

    Port number

    Set this parameter to the COM port connected to the IEC103 device.

    Address

    Set this parameter to the communication address of the IEC103 device.

  3. Set device monitoring parameters and click Submit.

    Figure 6-35 Device monitoring

    Tab

    Function

    Description

    Running Info.

    View the running information about the IEC103 device.

    N/A

    Teleindication

    View the device status, such as the switch status.

    N/A

    Telemetering

    View the real-time analog data of the device, such as the voltage.

    N/A

    Telecontrol

    Set the status control parameters, such as the parameters for turning on or off switches.

    Set the parameters on the tab page as required.

    Teleadjust

    Set analog parameters, for example, set voltage protection parameters.

    Set the parameters on the tab page as required.

Translation
Download
Updated: 2020-02-21

Document ID: EDOC1100108365

Views: 6961

Downloads: 1232

Average rating:
This Document Applies to these Products

Related Version

Related Documents

Share
Previous Next