Indicators and Buttons on the Front Panel

Atlas 800 Inference Server User Guide (Model 3000) 14

Rate and give feedback:

Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).

Figure 2-7 shows the indicators and buttons on the front panel of a server with 12 x 3.5-inch drives.
Figure 2-7 Indicators and buttons on the front panel of a server with 12 x 3.5-inch drives

1

UID button/indicator

2

Health status indicator

3

Power button/indicator

4

Fault diagnosis LED

5

FlexIO card presence indicators (1 and 2)

-

-

Figure 2-8 shows the indicators and buttons on the front panel of a server with 25 x 2.5-inch drives.
Figure 2-8 Indicators and buttons on the front panel of a server with 25 x 2.5-inch drives

1

UID button/indicator

2

Health status indicator

3

Power button/indicator

4

Fault diagnosis LED

5

FlexIO card presence indicators (1 and 2)

-

-

Figure 2-9 shows the indicators and buttons on the front panel of a server with 8 x 2.5-inch SAS/SATA drives and 12 x 2.5-inch NVMe drives.
Figure 2-9 Indicators and buttons on the front panel of a server with 8 x 2.5-inch SAS/SATA drives and 12 x 2.5-inch NVMe drives

1

UID button/indicator

2

Health status indicator

3

Power button/indicator

4

Fault diagnosis LED

5

FlexIO card presence indicators (1 and 2)

-

-
Figure 2-10 shows the indicators and buttons on the front panel of a server with 24 x 2.5-inch SAS/SATA pass-through drives.
Figure 2-10 Indicators and buttons on the front panel of a server 24 x 2.5 SAS/SATA pass-through drives

1

UID button/indicator

2

Health status indicator

3

Power button/indicator

4

Fault diagnosis LED

5

FlexIO card presence indicators (1 and 2)

-

-

When powered by Kunpeng 920 5220 or 3210 processors, the server does not support 24 x 2.5-inch SAS/SATA pass-through drive configuration.
Figure 2-11 shows the indicators and buttons on the front panel of a server with 8 x 2.5-inch drives.
Figure 2-11 Indicators and buttons on the front panel of a server with 8 x 2.5-inch drives
1

UID button/indicator

2

Health status indicator

3

Power button/indicator

4

Fault diagnosis LED

5

FlexIO indicator

-

-

Table 2-3 Indicators and buttons on the front panel

Silkscreen	Indicator/Button	Description
	Fault diagnosis LED	---: The server is operating properly. Error code: A server component is faulty. For details about error code, see the Atlas 800 Inference Server iBMC Alarm Handling (Model 3000).
	Power button/indicator	Power indicator: Steady yellow: The server is in standby state (ready to be powered on). Steady green: The server is properly powered on. Blinking yellow: The iBMC is starting. Off: The device is not powered on. Power button: When the server is powered on, you can press this button to shut down the OS gracefully. When the server is powered on, holding down this button for 6 seconds will forcibly power off the server. When the server is ready to be powered on, you can press this button to start the server.
	UID button/indicator	The UID button/indicator helps identify and locate a server. UID indicator: Off: The device is not being located. Blinking blue (blinking 255 seconds): The server is being located and differentiated from other servers that have also been located. Steady blue: The device is being located. UID button: You can turn on, turn off, or blink the UID indicator by pressing the UID button on the panel or by using the iBMC CLI or WebUI. You can press this button to turn on or off the UID indicator. You can press and hold down the UID indicator for 5 seconds to reset the iBMC.
	Health status indicator	Steady green: The device is operating properly. Blinking red at 1 Hz: A major alarm has been generated on the server. Blinking red at 5 Hz: A critical alarm has been generated on the server.
	FlexIO card presence indicators (1 and 2)	1 indicates FlexIO card 1, and 2 indicates FlexIO card 2. Steady green: The FlexIO card is installed and can be identified. Off: The FlexIO card is not installed or is faulty.