No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Enterprise
Worldwide
Huawei Global - English
Search
Support Documentation
Atlas 800 Inference Server Maintenance and Service Guide (Model 3010) 16
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Installing a SAS/SATA Drive

Installing a SAS/SATA Drive

  • The SATA or SAS drives support hot swap. After a faulty drive is disconnected from its backplane, wait 30 seconds before removing it. The alarm will not be cleared immediately after a new drive is installed. It will be cleared after the RAID array rebuild is complete. Do not frequently hot-swap a drive to prevent new alarms.
  • To prevent damage caused by insufficient heat dissipation and high temperature, install components or filler panels in all drive slots.

Installing a Front SAS/SATA Drive

Procedure

  1. Check whether a front bezel is installed.

    • If yes, go to 2.
    • If no, go to 3.

  2. Remove the front bezel.

    For details, see Removing the Front Bezel.

  3. Take the spare part out of its ESD bag.
  4. Determine the slot and position of the drive.

    For details, see Drive Configurations and Drive Numbers.

  5. Remove the drive filler.

    Perform this operation only when a drive filler is installed.

  6. Install drives.

    1. Open the ejector lever and push the drive into the slot as far as it will go. See (1) in Figure 6-27.
    2. Ensure that the ejector lever is fastened to the chassis beam, and then close it to completely insert the drive into the slot. See (2) in Figure 6-27.
      Figure 6-27 Installing a drive

  7. Check the running status of the drive by observing its indicators.

    For details, see SAS/SATA Drive Indicators.

  8. Restore the drive data.

    Perform this operation only after you replace a drive.

    For details, see "Troubleshooting > Hard Drive Fault" of each RAID controller card in Huawei Server RAID Controller Card User Guide (x86).

  9. Check whether a front bezel is installed.

    • If yes, go to 10.
    • If no alarms exist, no further action is required.

  10. Install the front bezel

    For details, see Installing the Front Bezel.

Installing a Rear SAS/SATA Drive

Procedure

  1. Take the spare part out of its ESD bag.
  2. Determine the slot and position of the drive.

    For details, see Drive Configurations and Drive Numbers.

  3. Remove the drive filler.

    Perform this operation only when a drive filler is installed.

  4. Install drives.

    1. Open the ejector lever and push the drive into the slot as far as it will go. See (1) in Figure 6-28.
    2. Ensure that the ejector lever is fastened to the chassis beam, and then close it to completely insert the drive into the slot. See (2) in Figure 6-28.
      Figure 6-28 Installing a drive

  5. Check the running status of the drive by observing its indicators.

    For details, see SAS/SATA Drive Indicators.

  6. Restore the drive data.

    Perform this operation only after you replace a drive.

    For details, see "Troubleshooting > Hard Drive Fault" of each RAID controller card in Huawei Server RAID Controller Card User Guide (x86).

Installing a Built-in SAS/SATA Drive

Procedure

  1. Take the spare part out of its ESD bag.
  2. Determine the slot and position of the drive.

    For details, see Drive Configurations and Drive Numbers.

  3. Release the eject levers of the built-in drive module.

    If the chassis cover is away for too long while the server is powered on, some components will become overheated. Install the chassis cover within 3 minutes.

    1. Remove the chassis cover.

      For details, see Removing the Chassis Cover.

    2. Release the eject levers of the built-in drive module until it cannot rotate.
      Figure 6-29 Releasing ejector levers of the built-in drive module

  4. Remove the drive filler.

    Perform this operation only when a drive filler is installed.

  5. Install drives.

    1. Open the ejector lever and push the drive into the slot as far as it will go. See (1) in Figure 6-30.
    2. Ensure that the ejector lever is fastened to the chassis beam, and then close it to completely insert the drive into the slot. See (2) in Figure 6-30.
      Figure 6-30 Installing a drive

  6. Close ejector levers of the built-in drive module.

    1. Close the eject levers of the built-in drive module until it cannot move.
      Figure 6-31 Closing ejector levers of the built-in drive module
    2. Install the chassis cover.

      For details, see Installing the Chassis Cover.

  7. Check the running status of the drive by observing its indicators.

    For details, see SAS/SATA Drive Indicators.

  8. Restore the drive data.

    Perform this operation only after you replace a drive.

    For details, see "Troubleshooting > Hard Drive Fault" of each RAID controller card in Huawei Server RAID Controller Card User Guide (x86).

Translation
简体中文
Download
Updated: 2023-01-31

Document ID: EDOC1100115123

Views: 254343

Downloads: 83

Average rating:
This Document Applies to these Products

Related Version

Related Documents

Digital Signature File

Digital Signature Authentication Mode
Share
Previous Next

Copyright © 2023 Huawei Technologies Co., Ltd. All rights reserved.

You are going to visit :