SmartLi Technical Specifications

SmartLi 2.0 User Manual

The BOM Codes are 02312TDM and 02312TDM-001.

Rate and give feedback:

Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).

SmartLi Technical Specifications

Table 3-1 SmartLi physical specifications

Item	Specifications
Dimensions (H x W x D)	2000 mm x 600 mm x 850 mm
Weight	< 230 kg (excluding battery modules)
Circuit breaker	690 V AC/750 V DC, 500 A, 4P
Fuse	800 V DC, 315 A (one fuse for each battery string)
Cabling mode	Routed in and out from the top
IP rating	IP20

Table 3-2 SmartLi environmental specifications

Item	Specifications
Operating temperature	0–40°C CAUTION: When the operating temperature is beyond the range of 0°C to 40°C, the power backup capability of the system may be unavailable or not reach the rated value. When the operating temperature is below 0°C, the battery modules switch off the charge and discharge circuits. As a result, the battery modules cannot be charged or discharged. Start the air conditioner to heat the battery modules to 3°C or above, and the charge and discharge will be resumed.
Storage temperature	0–40°C
Relative humidity	5%–95% RH (non-condensing)
Altitude	0–4000 m (When the altitude ranges from 0 m to 1000 m, the power is not derated. When the altitude exceeds 1000 m, the power is derated as described in IEC 62040-3.)

Table 3-3 Safety

Item	Specifications
CE	EN 62619, EN 62040-1
CB	IEC 62619, IEC 62040-1

Table 3-4 EMC

Item	Specifications
Certification standard	EN/IEC 62040-2
Conducted emission (CE)	EN/IEC 62040-2
Radiated emission (RE)	EN/IEC 62040-2
ESD immunity	IEC 61000-4-2
Conducted susceptibility (CS)	EN/IEC 62040-2 EN/IEC 61000-4-6
Radiated susceptibility (RS)	EN/IEC 62040-2 EN/IEC 61000-4-3
Electrical fast transient (EFT)	EN/IEC 62040-2 IEC 61000-4-4
Surge	EN/IEC 62040-2 IEC 61000-4-5
Power magnetic susceptibility	IEC 61000-4-8

Table 3-5 Electrical specifications (single cabinet in typical scenarios)

Item		Full-Capacity Cabinet (8+8)	Half-Capacity Cabinet (8+0)	Full-Capacity Cabinet (7+7)	Half-Capacity Cabinet (7+0)
Number of battery modules		16	8	14	7
Rated voltage		512 V (3.2 V/cell)	512 V (3.2 V/cell)	448 V (3.2 V/cell)	448 V (3.2 V/cell)
Rated capacity		80 Ah	40 Ah	80 Ah	40 Ah
Energy		40.96 kWh	20.48 kWh	35.84 kWh	17.92 kWh
Charge voltage		544 V (3.4 V/cell)	544 V (3.4 V/cell)	476 V (3.4 V/cell)	476 V (3.4 V/cell)
Charge current (The actual maximum charge current depends on the maximum charge capability of the UPS.)		≤ 80 A (40 A by default)	≤ 40 A (20 A by default)	≤ 80 A (40 A by default)	≤ 40 A (20 A by default)
Maximum discharge current		500 A	250 A	500 A	250 A
Discharge capacity (Max. operating temperature: 27°C)	Maximum load power supported by a single cabinet	230 kW	115 kW	200 kW	100 kW
Discharge capacity (Max. operating temperature: 27°C)	Backup time	10 min	10 min	10 min	10 min
Discharge capacity (Max. operating temperature: 40°C)	Maximum load power supported by a single cabinet	200 kW	100 kW	-	-
Discharge capacity (Max. operating temperature: 40°C)	Backup time	10 min	10 min	-	-

When the UPS5000-E works with the SmartLi, its half-wave loading capacity is 5% of the SmartLi rated capacity (standard configuration).

Translation

简体中文

Download

Updated: 2022-12-16

Document ID: EDOC1100117183

Downloads: 2706

Average rating:

This Document Applies to these Products

Related Version

Digital Signature File

Digital Signature Authentication Mode

The BOM Codes are 02312TDM and 02312TDM-001.

Related Version

Related Documents

Digital Signature File