Installing PDUs for IDS Cabinets

Prerequisites

• The cabinet has been installed.
• All required tools have been prepared, including a Phillips screwdriver, M6 screws, M5 self-tapping screws, ladders, and protective gloves.

When Two IDS1000 Cabinets Are Connected

1. Wear protective gloves.
2. Install the PDU installation plate.
   1. Align the holes of the PDU installation plate with the holes on the rear of the IDS1000 cabinet, as shown in Table 4-19.
      Table 4-19 Mapping of holes for two connected cabinets

      PDU Installation Plate ID	Installation Hole of a PDU Installation Plate	Installation Hole of an IDS1000 Cabinet
      1	Holes on the 3rd row	Holes on the 2nd row from left to right
      2	Holes on the 2nd row	Holes on the 20th row from left to right
      3	Holes on the 2nd row	Holes on the 20th row from right to left
      4	Holes on the 1st row	Holes on the 2nd row from right to left

      Figure 4-55 shows the holes in a PDU installation plate and shows the position of installing the plates on the IDS1000 cabinets.

      Figure 4-55 Holes in a PDU installation plate and where to install the plates on the IDS1000 cabinets
      

   2. Use the Phillips screwdriver and four M5 self-tapping screws (two on the top and two on the bottom) to fix each PDU installation plate into the holes.

3. Install a PDU.
   1. Fit the upper and lower round tabs on the rear panel of the PDU into the pear-shaped holes on the PDU installation plate. Push them down to lock the PDU.
   2. Use the Phillips screwdriver and M6 screws to fix the PDU.
   3. Repeat Step 3.1 and Step 3.2 to install other PDUs.

4. Connect the ground cable of the PDU to the cabinet.
   1. Fasten the ground cable of the PDU to a ground screw hole on the cabinet using a ground screw.
   2. Repeat Step 4.1 to connect the ground cables of other PDUs.

When Three IDS1000 Cabinets Are Connected

1. Install the PDU installation plate.
   1. Confirm which cabinet the PDU installation plate should be installed on and the number of PDU installation plates.
   2. Align the holes of the PDU installation plate with the holes on the rear of the IDS1000 cabinet, as shown in Table 4-20.
      Table 4-20 Mapping of holes for three connected cabinets

      PDU Installation Plate ID	Installation Hole of a PDU Installation Plate	Installation Hole of an IDS1000 Cabinet
      1	Holes on the 3rd row	Holes on the 1st row from left to right
      2	Holes on the 3rd row	Holes on the 20th row from left to right
      3	Holes on the 2nd row	Holes on the 20th row from right to left
      4	Holes on the 2nd row	Holes on the 22nd row from right to left
      5	Holes on the 1st row	Holes on the 20th row from right to left
      6	Holes on the 1st row	Holes on the 1st row from right to left

      Figure 4-56 shows the holes in a PDU installation plate and shows the position of installing the plates on the IDS1000 cabinets.

      Figure 4-56 Holes in a PDU installation plate and where to install the plates on the IDS1000 cabinets
      

   3. Use the Phillips screwdriver and four M5 self-tapping screws (two on the top and two on the bottom) to fix each PDU installation plate into the holes.

2. Install a PDU.
   1. Fit the upper and lower round tabs on the rear panel of the PDU into the pear-shaped holes on the PDU installation plate. Push them downwards to lock the PDU.
   2. Use the Phillips screwdriver and M6 screws to fix the PDU.
   3. Repeat Step 2.1 and Step 2.2 to install other PDUs.

3. Connect the ground cable of the PDU.
   1. Fasten the ground cable of the PDU to a ground screw hole on the cabinet using a ground screw.
   2. Repeat Step 3.1 to connect the ground cables of other PDUs.

Prerequisites

• The cabinet has been installed.
• All required tools have been prepared, including a Phillips screwdriver, M6 screws, M5 self-tapping screws, ladders, and protective gloves.

1. (Optional) If there is a side installation plate, cable manager, or cable ring on the IDS2000 cabinet, remove it.
2. Install the PDU installation plate.
   1. Confirm which cabinet the PDU installation plate should be installed on and the number of PDU installation plates.
   2. Align the holes of the PDU installation plate with the 4th holes (from left to right) on the rear of the IDS2000 cabinet, as detailed in Figure 4-57.
      Figure 4-57 Positions of the PDU installation plate and the cabinet
      

   3. Use the Phillips screwdriver and three M5 self-tapping screws (one on the top, one in the middle, and one on the bottom) to fix the PDU installation plate into the holes.

3. Install the PDU.
   1. Fit the upper and lower round tabs on the PDU rear panel into the pear-shaped holes on the PDU installation plate. Push them downwards to lock the PDU.
   2. Use the Phillips screwdriver and M6 screws to fix the PDU.
   3. Repeat 3.a and 3.b to install other PDUs.

4. Connect the ground cable of the PDU. Fasten the ground cable of the PDU to a ground screw hole on the cabinet using a ground screw.