Optical Modules for Huawei S Series Switches

Optical Modules for Huawei S Series Switches

Rate and give feedback:

Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).

Important Notes About Using Optical Modules Certified for Huawei Switches
- How to Identify Huawei-Certified Switch Optical Modules
- Risks of Using Non-Huawei-Certified Switch Optical Modules
Understanding Optical Modules
Optical Modules Supported by Huawei S Series Switches
FAQs About Optical Modules
Optical Module Installation and Replacement
- Installing an Optical Module
- Replacing an Optical Module
Typical Troubleshooting Cases of Optical Module

Important Notes About Using Optical Modules Certified for Huawei Switches

How to Identify Huawei-Certified Switch Optical Modules

A switch must use optical or copper modules that have been certified for use on Huawei switches. Non-certified optical or copper modules cannot ensure transmission reliability and may affect service stability. Huawei is not liable for any problem caused by the use of non-certified optical or copper modules and will not fix such problems.
The methods provided here are only for reference. To confirm whether optical modules you are using have been certified for use on Huawei switches, contact Huawei technical support.

10GE or Lower Speed Optical Modules

Huawei started certification on 10GE or lower speed optical modules for switch products on July 1, 2013.

To determine whether optical modules delivered for Huawei switches before July 1, 2013 are certified ones, contact Huawei technical support.

If your optical modules are delivered after July 1, 2013, use either of the following methods to determine whether they have been certified by Huawei.

Method 1: Check for "HUAWEI" on the label

If an optical module has been certified by Huawei, its label contains "HUAWEI", as shown in Figure 1-1.

Figure 1-1 "HUAWEI" on the label of a Huawei-certified switch optical module

Method 2: Run the display transceiver command

An optical module has received Huawei switch certification if it meets the following conditions:

In the display elabel command output, the Manufactured field displays a date later than 2013-07-01.
In the display version command output, the displayed version is V200R001C00 or later.
In the display transceiver command output, the Vendor Name field displays HUAWEI.

The SFP-FE-SX-MM1310 (part number: 02315233) is a Huawei-certified 100M optical module. However, the Vendor Name field displays the original manufacturer name, instead of HUAWEI.

For copper modules, the Vendor Name field also displays the original manufacturer name, instead of HUAWEI.

40GE and 100GE Optical Modules

Huawei started certification on 40GE and 100GE optical modules for switch products on January 1, 2016.

To determine whether optical modules delivered for Huawei switches before January 1, 2016 are certified ones, contact Huawei technical support.

If your optical modules are delivered after January 1, 2016, use either of the following methods to determine whether they have been certified by Huawei.

Method 1: Check for "HUAWEI" on the label

If an optical module has been certified by Huawei, its label contains "HUAWEI", as shown in Figure 1-1.

Method 2: Run the display transceiver command

A 40GE or 100GE optical module has received Huawei switch certification if it meets the following conditions:

In the display elabel command output, the Manufactured field displays a date later than 2016-01-01.
In the display version command output, the displayed version is V200R008 or later.
In the display transceiver command output, the Vendor Name field displays HUAWEI.

For the optical modules connected to high-speed cables or AOC cables, the Vendor Name field displays the original manufacturer name, instead of HUAWEI. For the methods of checking whether such an optical module has been certified by Huawei, contact technical support personnel.

Risks of Using Non-Huawei-Certified Switch Optical Modules

During certification of optical modules for Huawei switches, Huawei completes comprehensive functionality verification to ensure quality of optical modules. The verified items include optical module plug/unplug, transmit optical power, receive optical power, signal transmission quality, data reading, error tolerance, compatibility, electromagnetic compatibility (EMC), and environmental parameters.

Non-Huawei-certified switch optical modules may cause the following problems:

Non-standard structure and size cause failures to install optical modules on adjacent optical interfaces.

Structures or sizes of some non-Huawei-certified optical modules do not comply with the Multi-Source Agreement (MSA). When such an optical module is installed on an optical interface, the size of this optical module hinders optical module installation on adjacent optical interfaces.
Data bus defects cause suspension of a switch's data bus.

Some non-Huawei-certified optical modules have defects in data bus designs. Using such an optical module on a switch causes suspension of the connected data bus on the switch. As a result, data on the suspended bus cannot be read.
Improper edge connector size damages electronic devices of optical interfaces.

If a non-Huawei-certified switch optical module with improper edge connector size is used on an optical interface, electronic devices of the optical interface will be damaged by short circuits.
Unnormalized temperature monitoring causes incorrect alarms.

The temperature monitoring systems of some non-Huawei-certified switch optical modules do not comply with industry standards and report temperature values higher than the real temperature. When such optical modules are used on a switch, the system will report incorrect temperature alarms.
Improper register settings cause errors or failures in reading parameters or diagnostic information.

Some non-Huawei-certified switch optical modules have improper register values on page A0, which can cause errors or failures when the system attempts to read parameters or diagnostic information from a data bus.
Some non-Huawei-certified switch optical modules are not designed in compliance with EMC standards and have low anti-interference capability. Additionally, they bring electromagnetic interference to nearby devices.
The operating temperature ranges of non-Huawei-certified switch optical modules cannot meet service requirements. When they are used under relatively high temperature, the optical power decreases, resulting in service interruption.

Understanding Optical Modules

What Is an Optical Module

On an optical network, a sender needs to convert electrical signals into optical signals before sending them to a receiver, and the receiver needs to convert received optical signals into electrical signals. An optical module is a component that completes electrical/optical conversion on an optical network. Figure 1-2 shows the structure of an optical module.

Figure 1-2 Structure of an optical module (using an SFP/eSFP optical module as an example)

1. Handle	2. Receiver	3. Transmitter
4. Shell	5. Label	6. Dust plug
7. Spring	8. Connector	-

Figure 1-3 shows an SFP/eSFP optical module.

Figure 1-3 SFP/eSFP optical module

Figure 1-4 shows the appearance of an SFP+ optical module.

Figure 1-4 Appearance of an SFP+ optical module

Figure 1-5 and Figure 1-6 show the appearance of a QSFP+ optical module.

Figure 1-5 Appearance of a QSFP+ optical module (for LC optical fibers)

Figure 1-6 Appearance of a QSFP+ optical module (for MPO optical fibers)

The side with an L-shaped notch close to the connector is the top of a QSFP+ optical module, as shown in Figure 1-5. When connecting a QSFP+ optical module to a port, keep the top side upward. Do not insert the QSFP+ optical module upside down.

Currently, there is no formal standard for 40G Ethernet. Therefore, a device may not display complete diagnostic information about 40GE optical modules. This is an acceptable fact in the telecommunications industry and does not affect functions of 40GE optical modules.

Figure 1-7 shows the appearance of a CSFP optical module.

Figure 1-7 Appearance of a CSFP optical module

Figure 1-8 shows the appearance of an XFP module.

Figure 1-8 Appearance of an XFP optical module

The SFP+ and XFP optical modules are 10GE hot-pluggable optical modules. Compared with the SFP+ optical modules, the XFP optical modules have a larger caliber.

Figure 1-9 and Figure 1-10 show CFP optical modules for different optical fibers.

Figure 1-9 CFP 100GE optical module (for LC optical fibers)

Figure 1-10 CFP 100GE optical module (for MPO optical fibers)

Figure 1-11 and Figure 1-12 show the appearance of a QSFP28 optical module.

Figure 1-11 Appearance of a QSFP28 optical module (for MPO optical fibers)

Figure 1-12 Appearance of a QSFP28 optical module (for LC optical fibers)

Types of Optical Modules

Optical modules are available in various types to meet diversified requirements.

Classified by transmission rates

Depending on transmission rates, optical modules are classified into 100GE, 40GE, 10GE, FE, and GE optical modules.
Classified by encapsulation types

The higher transmission rate an optical module provides, the more complex structure it has. Optical modules are encapsulated in different modes to provide different structures. Huawei switches support optical modules of the following encapsulation types: CFP, QSFP+, QSFP28, XFP, SFP, eSFP, and SFP+. All optical modules are hot swappable.
- SFP: small form-factor pluggable. SFP optical modules support LC fiber connectors.
- eSFP: enhanced small form-factor pluggable. An eSFP module is an SFP module that supports monitoring of voltage, temperature, bias current, transmit optical power, and receive optical power. Therefore, eSFP is also called SFP sometimes.
- SFP+: small form-factor pluggable plus, SFP with a higher rate. SFP+ optical modules are more sensitive to electromagnetic interference (EMI) because they have a higher rate. To reduce EMI, SFP+ optical modules have more springs than SFP optical modules and the cages for SFP+ modules on a card are tighter.
- XFP: 10 Gigabit small form-factor pluggable. X is the Roman numeral 10, meaning that all XFP optical modules provide a 10 Gbit/s transmission rate. XFP optical modules support LC fiber connectors. They are wider and longer than SFP+ optical modules.
- QSFP+: quad small form-factor pluggable. QSFP+ optical modules support MPO fiber connectors and are larger than SFP+ optical modules.
- CFP: centum form-factor pluggable. The dimensions of a CFP optical module are 144.75 mm x 82 mm x 13.6 mm (L x W x H). CFP is a new optical module standard that can be used in data communication and telecommunications fields.
- QSFP28: with the same interface size as a QSFP+ module. A QSFP28 interface can use a 100GE QSFP28 optical module or a 40GE QSFP+ optical module.
Classified by physical layer standards

Different physical layer standards are defined to allow data transmission in different modes. Therefore, different types of optical modules are produced to comply with these standards. For details, see Standards compliance of the specific optical module.
Classified by modes

Optical fibers are classified into single-mode and multimode fibers. Therefore, optical modules are also classified into single-mode and multimode modules to support different optical fibers.
- Single-mode optical modules are used with single-mode fibers. Single-mode fibers support a wide band and large transmission capacity, and are used for long-distance transmission.
- Multimode optical modules are used with multimode fibers. Multimode fibers have lower transmission performance than single-mode fibers because of modal dispersion, but their costs are also lower. They are used for small-capacity, short-distance transmission.

Wavelength division multiplexing modules differ from other optical modules in center wavelengths. A common optical module has a center wavelength of 850 nm, 1310 nm, or 1550 nm, whereas a wavelength division multiplexing module transmits lights with different center wavelengths. Wavelength division multiplexing modules are classified into two types: coarse wavelength division multiplexing (CWDM) and dense wavelength division multiplexing (DWDM). Within the same band, DWDM modules are available in more types and use wavelength resources more efficiently than CWDM modules. DWDM and CWDM modules allow lights with different center wavelengths to be transmitted on one fiber without interfering each other. Therefore, a passive multiplexer can be used to combine the lights into one channel, which is then split into multiple channels by a demultiplexer on the remote end. This reduces the optical fibers required. DWDM and CWDM modules are used for long-distance transmission.

The transmit power of a long-distance optical module is often larger than its overload power. Therefore, when using such optical modules, select optical fibers of an appropriate length to ensure that the actual receive power is smaller than the overload power. If the optical fibers connected to a long-distance optical module are too short, use an optical attenuator to reduce the receive power on the remote optical module. Otherwise, the remote optical module may be burnt. Generally, an optical attenuator is required if an optical module supporting a transmission distance longer than 10 km is used together with short optical fibers.

Parameter Description

Transmit optical power: Output optical power of an optical module when it is working properly. When two optical modules are connected, the transmit optical power of one end must be within the range of receive optical power on the other end.

Receive optical power: Average input optical power that the receiver of an optical module can receive within a range of bit error rate (BER = 10^-12). The upper limit of this parameter is the overload optical power and the lower limit is the maximum receiver sensitivity. When two optical modules are connected, the receive optical power on one end determines the range of transmit optical power on the other end.

Maximum receiver sensitivity: Minimum average input optical power that the receiver of an optical module can receive within a range of bit error rate (BER = 10^-12). When two optical modules are connected, the maximum receiver sensitivity on one end determines the minimum value of transmit optical power on the other end.

Overload optical power: Maximum average input optical power that the receiver of an optical module can receive within a range of bit error rate (BER = 10^-12). When two optical modules are connected, the overload optical power on one end determines the maximum transmit optical power on the other end.

Extinction ratio: Minimum ratio of the average optical power with signals transmitted against the average optical power without signals transmitted in complete modulation mode. The extinction ratio indicates the capability of an optical module to identify signal 0 and signal 1. This parameter is a quality indicator for optical modules. Optical modules with a large extinction ratio may not have good quality. Qualified optical modules should have an extinction ratio complying with IEEE 802.3.

Fiber mode: Mode of optical fibers defined based on core diameters and features of optical fibers. Optical fibers are classified into single-mode and multimode fibers. Generally, multimode fibers have large core diameters and severe dispersion, so they transmit optical signals over short distances. Single-mode fibers have low dispersion and can transmit optical signals over long distances.

Modal bandwidth: Bandwidth measured at a point with transmit power several dB lower than that of the point with the peak center wavelength. Modal bandwidth reflects spectrum characteristics of multimode fibers. The higher modal bandwidth a multimode fiber has, the longer transmission distance the fiber supports.

Fiber diameter: Diameter of the core of a fiber. According to international standards for optical fibers, the diameter of a multimode fiber is 62.5 um or 50 um, and the diameter of a single-mode fiber is 9 um. Select optical fibers with diameters supported by the optical modules.

Fiber class: Optical signals with different wavelengths have their best working windows in different optical fibers. To help efficiently adjust wavelengths or dispersion features of optical fibers and change their refractive indexes, the following fiber classes are defined: multimode fiber (G.651), common single-mode fiber (G.652), shifted dispersion fiber (G.653), and non-zero shifted dispersion fiber (G.655). G.651 and G.652 are commonly used fiber classes. Optical fibers of higher classes support longer transmission distances. When selecting optical fibers for optical modules, determine the classes of fibers based on the required transmission distances.

Connector type: Type of the interface on an optical module to accommodate a fiber. Commonly used connector types are LC (applicable to all the SFP, SFP+, and XFP modules), SC, and MPO (applicable to 150 m QSFP+ and CXP modules). Select optical fibers with connectors supported by the optical modules.

Transmission distance: Maximum distance over which optical signals can transmit. Optical signals sent from different types of sources can transmit over different distances due to negative effects of optical fibers, such as dispersion and attenuation. When connecting optical interfaces, select optical modules and fibers based on the maximum signal transmission distance.

Interface rate: Maximum rate of electrical signals that an optical component can transmit without bit errors. The interface rates defined in Ethernet standards include 125 Mbit/s, 1.25 Gbit/s, 10.3125 Gbit/s, and 41.25 Gbit/s. When connecting optical interfaces, select optical modules and fibers based on the maximum signal transmission rate.

Center wavelength: Wavelength measured at the midpoint of the half-amplitude line in the transmit spectrum. Two connected optical modules must have the same center wavelength.

MSA: Multi-Source Agreement, a non-profit organization jointly established by optical module manufacturers. This agreement defines the structure and dimensions of optical transceivers by referring to Optical Internetworking Forum (OIF) and International Telecommunication Union (ITU) standards.

How to View Optical Module Parameters

Viewing the Hardware Description

If you know the model or type of an optical module, you can view the section "Pluggable Modules for Interfaces" in the Hardware Description to look up parameters of the optical module, including the center wavelength, transmission distance, fiber types supported, receive optical power, and transmit optical power.

Using a Command

If an optical module is installed in a running switch, you can run the display transceiver command to view parameters of the optical module, including the center wavelength, transmission distance, fiber types supported, receive optical power, and transmit optical power.

Rules for Optical Module Interoperation

Interoperation Rules

Optical modules with the same standards can interoperate with each other. The standards define the rate, wavelength, and transmission distance of optical modules, but not their encapsulation modes (two interoperated optical modules can have different encapsulation modes).

If you need to achieve interoperability between optical modules with different standards, contact technical support personnel.

When Huawei switches are connected to other products such as routers, comply with the preceding optical module interoperation rules.

Standards Description

The following describes the standards, using 1000BASE-LX10 as an example:

1000 indicates the rate (1000 Mbit/s, in this case). Other rates include 10 Mbit/s, 100 Mbit/s, 10 Gbit/s, 40 Gbit/s, and 100 Gbit/s.
BASE indicates baseband transmission.
L represents a center wavelength of the laser. Currently, the following center wavelengths are available: S (short wavelength: 850 nm), L (long wavelength: 1310 nm), E (extra long wavelength: 1550 nm), and B (single-fiber bidirectional long wavelength).
X represents the encoding format. The encoding formats include T (twisted pair), X (8B/10B), R (64B/66B), and W (WIS).
10 indicates the number of channels. Currently, the value can be 4 or 10. If there is no number, the value is 1.

This example provides the definitions in IEEE standards, which are not applicable to all optical modules, for example, non-standard optical modules.

The following organizations or agreements define standards related to optical modules:

IEEE 802.3, which defines MAC and PHY standards
Small Form Factor (SFF) committee or Multi-Source Agreements (MSAs), which define optical module hardware, software, and structure standards

Interoperability of 40GE and 100GE Optical Modules

Huawei S series switches support the following types of 40GE and 100GE optical modules:

40GE QSFP+ optical modules
40GE CFP optical modules
100GE CFP optical modules
100GE QSFP28 optical modules

Figure 1-13 Interoperability of 40GE optical modules in different encapsulation modes

Figure 1-14 Interoperability of 100GE optical modules in different encapsulation modes

Optical modules complying with the standards connected in the preceding figures can interoperate with each other.

iSR4 and eSR4 are non-standard formats derived from SR4, and support interoperation with SR4.

A 40GBASE-PAM4 optical module can interoperate with a 40GBASE-ePAM4 optical module.

A 100GBASE-CLR4 optical module can interoperate with a 100GBASE-CWDM4 optical module.

A 100GBASE-ER4-lite optical module can interoperate with a 100GBASE-ER4 optical module, at a maximum distance of 30 km.

Optical Modules Supported by Huawei S Series Switches

FE SFP/eSFP Optical Modules

SFP-FE-SX-MM1310

Table 1-1 Technical specifications

Item	Description
Transceiver form factor	SFP
Transmission speed	FE
Center wavelength (nm)	1310
Standards compliance	100BASE-FX
Connector type	LC
Applicable cable and maximum transmission distance	Multimode fiber (50 μm or 62.5 μm diameter): 2 km
Transmit power (dBm)	-19.0 to -14.0
Maximum receiver sensitivity (dBm)	-30.0
Overload power (dBm)	-14.0
Extinction ratio (dB)	10
Operating temperature	0°C to 70°C (32°F to 158°F)
Part number	02315233

eSFP-FE-LX-SM1310

Table 1-2 Technical specifications

Item	Description
Transceiver form factor	eSFP
Transmission speed	FE
Center wavelength (nm)	1310
Standards compliance	Non-standard
Connector type	LC
Applicable cable and maximum transmission distance	Single-mode fiber: 15 km
Transmit power (dBm)	-15.0 to -8.0
Maximum receiver sensitivity (dBm)	-28.0
Overload power (dBm)	-8.0
Extinction ratio (dB)	8.2
Operating temperature	0°C to 70°C (32°F to 158°F)
Part number	02315205

S-SFP-FE-LH40-SM1310

Table 1-3 Technical specifications

Item	Description
Transceiver type	eSFP
Transmission speed	FE
Center wavelength (nm)	1310
Standards compliance	Non-standard
Connector type	LC
Applicable cable and maximum transmission distance	Single-mode fiber: 40 km
Transmit power (dBm)	-5.0 to 0
Maximum receiver sensitivity (dBm)	-37.0
Overload power (dBm)	-10.0
Extinction ratio (dB)	10.5
Operating temperature	0°C to 70°C (32°F to 158°F)
Part number	02317344

S-SFP-FE-LH80-SM1550

Table 1-4 Technical specifications

Item	Description
Transceiver form factor	eSFP
Transmission speed	FE
Center wavelength (nm)	1550
Standards compliance	Non-standard
Connector type	LC
Applicable cable and maximum transmission distance	Single-mode fiber: 80 km
Transmit power (dBm)	-5.0 to 0
Maximum receiver sensitivity (dBm)	-37.0
Overload power (dBm)	-10.0
Extinction ratio (dB)	10.5
Operating temperature	0°C to 70°C (32°F to 158°F)
Part number	02317345

SFP-FE-LX-SM1310-BIDI (Single-Fiber-Bidirectional Module)

Table 1-5 Technical specifications

Item	Description
Transceiver form factor	eSFP
Transmission speed	FE
Center wavelength (nm)	Rx: 1550/Tx: 1310
Standards compliance	100BASE-BX
Connector type	LC
Applicable cable and maximum transmission distance	Single-mode fiber: 15 km
Transmit power (dBm)	-15.0 to -8.0
Maximum receiver sensitivity (dBm)	-32.0
Overload power (dBm)	-8.0
Extinction ratio (dB)	8.5
Operating temperature	0°C to 70°C (32°F to 158°F)
Part number	02315203

BIDI optical modules must be used in pairs. For example, SFP-FE-LX-SM1310-BIDI must be used with SFP-FE-LX-SM1550-BIDI.

SFP-FE-LX-SM1550-BIDI (Single-Fiber-Bidirectional Module)

Table 1-6 Technical specifications

Item	Description
Transceiver form factor	eSFP
Transmission speed	FE
Center wavelength (nm)	Rx: 1310/Tx: 1550
Standards compliance	100BASE-BX
Connector type	LC
Applicable cable and maximum transmission distance	Single-mode fiber: 15 km
Transmit power (dBm)	-15.0 to -8.0
Maximum receiver sensitivity (dBm)	-32.0
Overload power (dBm)	-8.0
Extinction ratio (dB)	8.5
Operating temperature	0°C to 70°C (32°F to 158°F)
Part number	02315202

BIDI optical modules must be used in pairs. For example, SFP-FE-LX-SM1550-BIDI must be used with SFP-FE-LX-SM1310-BIDI.

GE eSFP Optical Modules

eSFP-GE-SX-MM850

Table 1-7 Technical specifications

Item	Description
Transceiver form factor	eSFP
Transmission speed	GE
Center wavelength (nm)	850
Standards compliance	1000BASE-SX
Connector type	LC
Applicable cable and maximum transmission distance	Multimode fiber (with modal bandwidth of 160 MHzkm and diameter of 62.5 μm): 0.22 km Multimode fiber (OM1): 0.275 km Multimode fiber (with modal bandwidth of 400 MHzkm and diameter of 50 μm): 0.5 km Multimode fiber (OM2): 0.55 km Multimode fiber (OM3): 1 km
Transmit power (dBm)	-9.5 to -2.5
Maximum receiver sensitivity (dBm)	-17.0
Overload power (dBm)	0
Extinction ratio (dB)	9
Operating temperature	0°C to 70°C (32°F to 158°F)
Part number	02315204

SFP-GE-LX-SM1310

Table 1-8 Technical specifications

Item	Description
Transceiver form factor	eSFP
Transmission speed	GE
Center wavelength (nm)	1310
Standards compliance	1000BASE-LX10/LH
Connector type	LC
Applicable cable and maximum transmission distance	Single-mode fiber: 10 km
Transmit power (dBm)	-9.0 to -3.0
Maximum receiver sensitivity (dBm)	-20.0
Overload power (dBm)	-3.0
Extinction ratio (dB)	9
Operating temperature	0°C to 70°C (32°F to 158°F)
Part number	02315200

S-SFP-GE-LH40-SM1310

Table 1-9 Technical specifications

Item	Description
Transceiver type	eSFP
Transmission speed	GE
Center wavelength (nm)	1310
Standards compliance	1000BASE-EX (non-standard)
Connector type	LC
Applicable cable and maximum transmission distance	Single-mode fiber: 40 km
Transmit power (dBm)	-5.0 to 0
Maximum receiver sensitivity (dBm)	-23
Overload power (dBm)	-3.0
Extinction ratio (dB)	9
Operating temperature	0°C to 70°C (32°F to 158°F)
Part number	02317346

S-SFP-GE-LH40-SM1550

Table 1-10 Technical specifications

Item	Description
Transceiver type	eSFP
Transmission speed	GE
Center wavelength (nm)	1550
Standards compliance	Non-standard
Connector type	LC
Applicable cable and maximum transmission distance	Single-mode fiber: 40 km
Transmit power (dBm)	-5.0 to 0
Maximum receiver sensitivity (dBm)	-22
Overload power (dBm)	-3.0
Extinction ratio (dB)	9
Operating temperature	0°C to 70°C (32°F to 158°F)
Part number	02317347

S-SFP-GE-LH80-SM1550

Table 1-11 Technical specifications

Item	Description
Transceiver type	eSFP
Transmission speed	GE
Center wavelength (nm)	1550
Standards compliance	1000BASE-ZX
Connector type	LC
Applicable cable and maximum transmission distance	Single-mode fiber: 80 km
Transmit power (dBm)	-2.0 to +5.0
Maximum receiver sensitivity (dBm)	-23
Overload power (dBm)	-3.0
Extinction ratio (dB)	9
Operating temperature	0°C to 70°C (32°F to 158°F)
Part number	02317348

eSFP-GE-ZX100-SM1550

Table 1-12 Technical specifications

Item	Description
Transceiver form factor	eSFP
Transmission speed	GE
Center wavelength (nm)	1550
Standards compliance	1000BASE-ZX
Connector type	LC
Applicable cable and maximum transmission distance	Single-mode fiber: 100 km
Transmit power (dBm)	0 to 5
Maximum receiver sensitivity (dBm)	-30.0
Overload power (dBm)	-9.0
Extinction ratio (dB)	9.5
Operating temperature	0°C to 70°C (32°F to 158°F)
Part number	02315206

SFP-GE-LX-SM1310-BIDI (Single-Fiber-Bidirectional Module)

Table 1-13 Technical specifications

Item	Description
Transceiver type	eSFP
Transmission speed	GE
Center wavelength (nm)	Rx: 1490/Tx: 1310
Standards compliance	1000BASE-BX10
Connector type	LC
Applicable cable and maximum transmission distance	Single-mode fiber: 10 km
Transmit power (dBm)	-9.0 to -3.0
Maximum receiver sensitivity (dBm)	-19.5
Overload power (dBm)	-3.0
Extinction ratio (dB)	6
Operating temperature	0°C to 70°C (32°F to 158°F)
Part number	02315285

Single-fiber bidirectional (BIDI) optical modules must be used in pairs. For example, SFP-GE-LX-SM1310-BIDI must be used with SFP-GE-LX-SM1490-BIDI.

SFP-GE-LX-SM1490-BIDI (Single-Fiber-Bidirectional Module)

Table 1-14 Technical specifications

Item	Description
Transceiver type	eSFP
Transmission speed	GE
Center wavelength (nm)	Rx: 1310/Tx: 1490
Standards compliance	1000BASE-BX10
Connector type	LC
Applicable cable and maximum transmission distance	Single-mode fiber: 10 km
Transmit power (dBm)	-9.0 to -3.0
Maximum receiver sensitivity (dBm)	-19.5
Overload power (dBm)	-3.0
Extinction ratio (dB)	6
Operating temperature	0°C to 70°C (32°F to 158°F)
Part number	02315286

Single-fiber bidirectional (BIDI) optical modules must be used in pairs. For example, SFP-GE-LX-SM1490-BIDI must be used with SFP-GE-LX-SM1310-BIDI.

LE2MGSC40DE0 (Single-Fiber-Bidirectional Module)

Table 1-15 Technical specifications

Item	Description
Transceiver form factor	eSFP
Transmission speed	GE
Center wavelength (nm)	Rx: 1490/Tx: 1310
Standards compliance	1000BASE-BX
Connector type	LC
Applicable cable and maximum transmission distance	Single-mode fiber: 40 km
Transmit power (dBm)	-2.0 to +3.0
Maximum receiver sensitivity (dBm)	-23
Overload power (dBm)	-3.0
Extinction ratio (dB)	9
Operating temperature	0°C to 70°C (32°F to 158°F)
Part number	02310KVV

Single-fiber bidirectional (BIDI) optical modules must be used in pairs. For example, LE2MGSC40DE0 must be used with LE2MGSC40ED0.

LE2MGSC40ED0 (Single-Fiber-Bidirectional Module)

Table 1-16 Technical specifications

Item	Description
Transceiver form factor	eSFP
Transmission speed	GE
Center wavelength (nm)	Rx: 1310/Tx: 1490
Standards compliance	1000BASE-BX
Connector type	LC
Applicable cable and maximum transmission distance	Single-mode fiber: 40 km
Transmit power (dBm)	-2.0 to +3.0
Maximum receiver sensitivity (dBm)	-23
Overload power (dBm)	-3.0
Extinction ratio (dB)	9
Operating temperature	0°C to 70°C (32°F to 158°F)
Part number	02310KVU

Single-fiber bidirectional (BIDI) optical modules must be used in pairs. For example, LE2MGSC40ED0 must be used with LE2MGSC40DE0.

SFP-GE-ZBXD1 (Single-Fiber-Bidirectional Module)

Table 1-17 Technical specifications

Item	Description
Transceiver type	eSFP
Transmission speed	GE
Center wavelength (nm)	Rx: 1490/Tx: 1570
Standards compliance	Non-standard
Connector type	LC
Applicable cable and maximum transmission distance	Single-mode fiber: 80 km
Transmit power (dBm)	-2.0 to +4.0
Maximum receiver sensitivity (dBm)	-26
Overload power (dBm)	-3.0
Extinction ratio (dB)	9
Operating temperature	0°C to 70°C (32°F to 158°F)
Part number	02311DDB

This module can only be used on a switch running V200R008C00 or a later version. A switch running an earlier version may fail to obtain information about this module.

Single-fiber bidirectional (BIDI) optical modules must be used in pairs. For example, SFP-GE-ZBXD1 must be used with SFP-GE-ZBXU1.

SFP-GE-ZBXU1 (Single-Fiber-Bidirectional Module)

Table 1-18 Technical specifications

Item	Description
Transceiver type	eSFP
Transmission speed	GE
Center wavelength (nm)	Rx: 1570/Tx: 1490
Standards compliance	Non-standard
Connector type	LC
Applicable cable and maximum transmission distance	Single-mode fiber: 80 km
Transmit power (dBm)	-2.0 to +4.0
Maximum receiver sensitivity (dBm)	-26
Overload power (dBm)	-3.0
Extinction ratio (dB)	9
Operating temperature	0°C to 70°C (32°F to 158°F)
Part number	02311DDC

This module can only be used on a switch running V200R008C00 or a later version. A switch running an earlier version may fail to obtain information about this module.

Single-fiber bidirectional (BIDI) optical modules must be used in pairs. For example, SFP-GE-ZBXU1 must be used with SFP-GE-ZBXD1.

SFP-GE-BXU1-SC (Single-Fiber-Bidirectional Module)

Table 1-19 Technical specifications

Item	Description
Transceiver form factor	eSFP
Transmission speed	GE
Center wavelength (nm)	Rx: 1310/Tx: 1490
Standards compliance	Non-standard
Connector type	SC
Applicable cable and maximum transmission distance	Single-mode fiber: 10 km
Transmit power (dBm)	-9.0 to -3.0
Maximum receiver sensitivity (dBm)	-19.5
Overload power (dBm)	-3.0
Extinction ratio (dB)	9
Operating temperature	0°C to 70°C (32°F to 158°F)
Part number	02310TQH

GE CSFP Optical Modules

CSFP-GE-FE-BXD1

Table 1-20 Technical specifications

Item	Description
Transceiver form factor	CSFP
Transmission speed	FE/GE auto-sensing
Center wavelength (nm)	Rx: 1310/Tx: 1490
Standards compliance	1000BASE-BX10
Connector type	LC
Applicable cable and maximum transmission distance	Single-mode fiber: 10 km
Transmit power (dBm)	-9.0 to -3.0
Maximum receiver sensitivity (dBm)	-23
Overload power (dBm)	-3.0
Extinction ratio (dB)	6.6
Operating temperature	0°C to 70°C (32°F to 158°F)
Part number	02310TEE

If a CSFP optical module is installed on a switch that does not support it, the switch cannot detect whether the optical module is present.

CSFP-GE-FE-BIDI2

Table 1-21 Technical specifications

Item	Description
Transceiver form factor	CSFP
Transmission speed	FE/GE auto-sensing
Center wavelength (nm)	Rx: 1310/Tx: 1490
Standards compliance	Non-standard
Connector type	LC
Applicable cable and maximum transmission distance	Single-mode fiber: 20 km
Transmit power (dBm)	-9.0 to -3.0
Maximum receiver sensitivity (dBm)	-23
Overload power (dBm)	-3.0
Extinction ratio (dB)	6.6
Operating temperature	0°C to 70°C (32°F to 158°F)
Part number	02310WRR

If a CSFP optical module is installed on a switch that does not support it, the switch cannot detect whether the optical module is present.

CSFP-GE-FE-BIDI4

Table 1-22 Technical specifications

Item	Description
Transceiver form factor	CSFP
Transmission speed	FE/GE auto-sensing
Center wavelength (nm)	Rx: 1310/Tx: 1490
Standards compliance	1000BASE-BX
Connector type	LC
Applicable cable and maximum transmission distance	Single-mode fiber: 40 km
Transmit power (dBm)	-5.0 to 0
Maximum receiver sensitivity (dBm)	-25
Overload power (dBm)	0
Extinction ratio (dB)	6.6
Operating temperature	-40°C to +85°C (-40°F to +185°F)
Part number	02310XQV

If a CSFP optical module is installed on a switch that does not support it, the switch cannot detect whether the optical module is present.

GE-CWDM eSFP Optical Modules

CWDM-SFPGE-1471

Table 1-23 Technical specifications

Item	Description
Transceiver form factor	eSFP
Transmission speed	GE
Center wavelength (nm)	1471
Standards compliance	GE-CWDM
Connector type	LC
Applicable cable and maximum transmission distance	Single-mode fiber: 80 km
Transmit power (dBm)	0 to 5.0
Maximum receiver sensitivity (dBm)	-28.0
Overload power (dBm)	-9.0
Extinction ratio (dB)	8.5
Operating temperature	0°C to 70°C (32°F to 158°F)
Part number	02310LPN

CWDM-SFPGE-1491

Table 1-24 Technical specifications

Item	Description
Transceiver form factor	eSFP
Transmission speed	GE
Center wavelength (nm)	1491
Standards compliance	GE-CWDM
Connector type	LC
Applicable cable and maximum transmission distance	Single-mode fiber: 80 km
Transmit power (dBm)	0 to 5.0
Maximum receiver sensitivity (dBm)	-28.0
Overload power (dBm)	-9.0
Extinction ratio (dB)	8.5
Operating temperature	0°C to 70°C (32°F to 158°F)
Part number	02310LPK

CWDM-SFPGE-1511

Table 1-25 Technical specifications

Item	Description
Transceiver form factor	eSFP
Transmission speed	GE
Center wavelength (nm)	1511
Standards compliance	GE-CWDM
Connector type	LC
Applicable cable and maximum transmission distance	Single-mode fiber: 80 km
Transmit power (dBm)	0 to 5.0
Maximum receiver sensitivity (dBm)	-28.0
Overload power (dBm)	-9.0
Extinction ratio (dB)	8.5
Operating temperature	0°C to 70°C (32°F to 158°F)
Part number	02310LPH

CWDM-SFPGE-1531

Table 1-26 Technical specifications

Item	Description
Transceiver form factor	eSFP
Transmission speed	GE
Center wavelength (nm)	1531
Standards compliance	GE-CWDM
Connector type	LC
Applicable cable and maximum transmission distance	Single-mode fiber: 80 km
Transmit power (dBm)	0 to 5.0
Maximum receiver sensitivity (dBm)	-28.0
Overload power (dBm)	-9.0
Extinction ratio (dB)	8.5
Operating temperature	0°C to 70°C (32°F to 158°F)
Part number	02310LPL

CWDM-SFPGE-1551

Table 1-27 Technical specifications

Item	Description
Transceiver form factor	eSFP
Transmission speed	GE
Center wavelength (nm)	1551
Standards compliance	GE-CWDM
Connector type	LC
Applicable cable and maximum transmission distance	Single-mode fiber: 80 km
Transmit power (dBm)	0 to 5.0
Maximum receiver sensitivity (dBm)	-28.0
Overload power (dBm)	-9.0
Extinction ratio (dB)	8.5
Operating temperature	0°C to 70°C (32°F to 158°F)
Part number	02312AXN

CWDM-SFPGE-1571

Table 1-28 Technical specifications

Item	Description
Transceiver form factor	eSFP
Transmission speed	GE
Center wavelength (nm)	1571
Standards compliance	GE-CWDM
Connector type	LC
Applicable cable and maximum transmission distance	Single-mode fiber: 80 km
Transmit power (dBm)	0 to 5.0
Maximum receiver sensitivity (dBm)	-28.0
Overload power (dBm)	-9.0
Extinction ratio (dB)	8.5
Operating temperature	0°C to 70°C (32°F to 158°F)
Part number	02312AXM

CWDM-SFPGE-1591

Table 1-29 Technical specifications

Item	Description
Transceiver form factor	eSFP
Transmission speed	GE
Center wavelength (nm)	1591
Standards compliance	GE-CWDM
Connector type	LC
Applicable cable and maximum transmission distance	Single-mode fiber: 80 km
Transmit power (dBm)	0 to 5.0
Maximum receiver sensitivity (dBm)	-28.0
Overload power (dBm)	-9.0
Extinction ratio (dB)	8.5
Operating temperature	0°C to 70°C (32°F to 158°F)
Part number	02312AXK

CWDM-SFPGE-1611

Table 1-30 Technical specifications

Item	Description
Transceiver form factor	eSFP
Transmission speed	GE
Center wavelength (nm)	1611
Standards compliance	GE-CWDM
Connector type	LC
Applicable cable and maximum transmission distance	Single-mode fiber: 80 km
Transmit power (dBm)	0 to 5.0
Maximum receiver sensitivity (dBm)	-28.0
Overload power (dBm)	-9.0
Extinction ratio (dB)	8.5
Operating temperature	0°C to 70°C (32°F to 158°F)
Part number	02310LPJ

GE-CWDM eSFP Optical Modules (Used Only in the OADM scenario)

CWDM-SFPGE-1271

Table 1-31 Technical specifications

Item	Description
Transceiver form factor	eSFP
Transmission speed	GE
Center wavelength (nm)	1271
Standards compliance	GE-CWDM
Connector type	LC
Applicable cable and maximum transmission distance	Single-mode fiber: 80 km
Transmit power (dBm)	0 to 5.0
Maximum receiver sensitivity (dBm)	-28.0
Overload power (dBm)	-9.0
Extinction ratio (dB)	8.5
Operating temperature	-5°C to +75°C (23°F to 167°F)
Part number	02312AXC

CWDM-SFPGE-1291

Table 1-32 Technical specifications

Item	Description
Transceiver form factor	eSFP
Transmission speed	GE
Center wavelength (nm)	1291
Standards compliance	GE-CWDM
Connector type	LC
Applicable cable and maximum transmission distance	Single-mode fiber: 80 km
Transmit power (dBm)	0 to 5.0
Maximum receiver sensitivity (dBm)	-28.0
Overload power (dBm)	-9.0
Extinction ratio (dB)	8.5
Operating temperature	-5°C to +75°C (23°F to 167°F)
Part number	02312AXB

CWDM-SFPGE-1311

Table 1-33 Technical specifications

Item	Description
Transceiver form factor	eSFP
Transmission speed	GE
Center wavelength (nm)	1311
Standards compliance	GE-CWDM
Connector type	LC
Applicable cable and maximum transmission distance	Single-mode fiber: 80 km
Transmit power (dBm)	0 to 5.0
Maximum receiver sensitivity (dBm)	-28.0
Overload power (dBm)	-9.0
Extinction ratio (dB)	8.5
Operating temperature	-5°C to +75°C (23°F to 167°F)
Part number	02312AXA

CWDM-SFPGE-1331

Table 1-34 Technical specifications

Item	Description
Transceiver form factor	eSFP
Transmission speed	GE
Center wavelength (nm)	1331
Standards compliance	GE-CWDM
Connector type	LC
Applicable cable and maximum transmission distance	Single-mode fiber: 80 km
Transmit power (dBm)	0 to 5.0
Maximum receiver sensitivity (dBm)	-28.0
Overload power (dBm)	-9.0
Extinction ratio (dB)	8.5
Operating temperature	-5°C to +75°C (23°F to 167°F)
Part number	02312AWY

CWDM-SFPGE-1351

Table 1-35 Technical specifications

Item	Description
Transceiver form factor	eSFP
Transmission speed	GE
Center wavelength (nm)	1351
Standards compliance	GE-CWDM
Connector type	LC
Applicable cable and maximum transmission distance	Single-mode fiber: 80 km
Transmit power (dBm)	0 to 5.0
Maximum receiver sensitivity (dBm)	-28.0
Overload power (dBm)	-9.0
Extinction ratio (dB)	8.5
Operating temperature	-5°C to +75°C (23°F to 167°F)
Part number	02312AWX

CWDM-SFPGE-1371

Table 1-36 Technical specifications

Item	Description
Transceiver form factor	eSFP
Transmission speed	GE
Center wavelength (nm)	1371
Standards compliance	GE-CWDM
Connector type	LC
Applicable cable and maximum transmission distance	Single-mode fiber: 80 km
Transmit power (dBm)	0 to 5.0
Maximum receiver sensitivity (dBm)	-28.0
Overload power (dBm)	-9.0
Extinction ratio (dB)	8.5
Operating temperature	-5°C to +75°C (23°F to 167°F)
Part number	02312AWW

CWDM-SFPGE-1391

Table 1-37 Technical specifications

Item	Description
Transceiver form factor	eSFP
Transmission speed	GE
Center wavelength (nm)	1391
Standards compliance	GE-CWDM
Connector type	LC
Applicable cable and maximum transmission distance	Single-mode fiber: 80 km
Transmit power (dBm)	0 to 5.0
Maximum receiver sensitivity (dBm)	-28.0
Overload power (dBm)	-9.0
Extinction ratio (dB)	8.5
Operating temperature	-5°C to +75°C (23°F to 167°F)
Part number	02312AWV

CWDM-SFPGE-1411

Table 1-38 Technical specifications

Item	Description
Transceiver form factor	eSFP
Transmission speed	GE
Center wavelength (nm)	1411
Standards compliance	GE-CWDM
Connector type	LC
Applicable cable and maximum transmission distance	Single-mode fiber: 80 km
Transmit power (dBm)	0 to 5.0
Maximum receiver sensitivity (dBm)	-28.0
Overload power (dBm)	-9.0
Extinction ratio (dB)	8.5
Operating temperature	-5°C to +75°C (23°F to 167°F)
Part number	02312AWU

CWDM-SFPGE-1431

Table 1-39 Technical specifications

Item	Description
Transceiver form factor	eSFP
Transmission speed	GE
Center wavelength (nm)	1431
Standards compliance	GE-CWDM
Connector type	LC
Applicable cable and maximum transmission distance	Single-mode fiber: 80 km
Transmit power (dBm)	0 to 5.0
Maximum receiver sensitivity (dBm)	-28.0
Overload power (dBm)	-9.0
Extinction ratio (dB)	8.5
Operating temperature	-5°C to +75°C (23°F to 167°F)
Part number	02312AWT

CWDM-SFPGE-1451

Table 1-40 Technical specifications

Item	Description
Transceiver form factor	eSFP
Transmission speed	GE
Center wavelength (nm)	1451
Standards compliance	GE-CWDM
Connector type	LC
Applicable cable and maximum transmission distance	Single-mode fiber: 80 km
Transmit power (dBm)	0 to 5.0
Maximum receiver sensitivity (dBm)	-28.0
Overload power (dBm)	-9.0
Extinction ratio (dB)	8.5
Operating temperature	-5°C to +75°C (23°F to 167°F)
Part number	02312AWS

CWDM-SFPGE-1471

Table 1-41 Technical specifications

Item	Description
Transceiver form factor	eSFP
Transmission speed	GE
Center wavelength (nm)	1471
Standards compliance	GE-CWDM
Connector type	LC
Applicable cable and maximum transmission distance	Single-mode fiber: 80 km
Transmit power (dBm)	0 to 5.0
Maximum receiver sensitivity (dBm)	-28.0
Overload power (dBm)	-9.0
Extinction ratio (dB)	8.5
Operating temperature	0°C to 70°C (32°F to 158°F)
Part number	02310LPN

CWDM-SFPGE-1491

Table 1-42 Technical specifications

Item	Description
Transceiver form factor	eSFP
Transmission speed	GE
Center wavelength (nm)	1491
Standards compliance	GE-CWDM
Connector type	LC
Applicable cable and maximum transmission distance	Single-mode fiber: 80 km
Transmit power (dBm)	0 to 5.0
Maximum receiver sensitivity (dBm)	-28.0
Overload power (dBm)	-9.0
Extinction ratio (dB)	8.5
Operating temperature	0°C to 70°C (32°F to 158°F)
Part number	02310LPK

CWDM-SFPGE-1511

Table 1-43 Technical specifications

Item	Description
Transceiver form factor	eSFP
Transmission speed	GE
Center wavelength (nm)	1511
Standards compliance	GE-CWDM
Connector type	LC
Applicable cable and maximum transmission distance	Single-mode fiber: 80 km
Transmit power (dBm)	0 to 5.0
Maximum receiver sensitivity (dBm)	-28.0
Overload power (dBm)	-9.0
Extinction ratio (dB)	8.5
Operating temperature	0°C to 70°C (32°F to 158°F)
Part number	02310LPH

CWDM-SFPGE-1531

Table 1-44 Technical specifications

Item	Description
Transceiver form factor	eSFP
Transmission speed	GE
Center wavelength (nm)	1531
Standards compliance	GE-CWDM
Connector type	LC
Applicable cable and maximum transmission distance	Single-mode fiber: 80 km
Transmit power (dBm)	0 to 5.0
Maximum receiver sensitivity (dBm)	-28.0
Overload power (dBm)	-9.0
Extinction ratio (dB)	8.5
Operating temperature	0°C to 70°C (32°F to 158°F)
Part number	02310LPL

CWDM-SFPGE-1551

Table 1-45 Technical specifications

Item	Description
Transceiver form factor	eSFP
Transmission speed	GE
Center wavelength (nm)	1551
Standards compliance	GE-CWDM
Connector type	LC
Applicable cable and maximum transmission distance	Single-mode fiber: 80 km
Transmit power (dBm)	0 to 5.0
Maximum receiver sensitivity (dBm)	-28.0
Overload power (dBm)	-9.0
Extinction ratio (dB)	8.5
Operating temperature	0°C to 70°C (32°F to 158°F)
Part number	02312AXN

CWDM-SFPGE-1571

Table 1-46 Technical specifications

Item	Description
Transceiver form factor	eSFP
Transmission speed	GE
Center wavelength (nm)	1571
Standards compliance	GE-CWDM
Connector type	LC
Applicable cable and maximum transmission distance	Single-mode fiber: 80 km
Transmit power (dBm)	0 to 5.0
Maximum receiver sensitivity (dBm)	-28.0
Overload power (dBm)	-9.0
Extinction ratio (dB)	8.5
Operating temperature	0°C to 70°C (32°F to 158°F)
Part number	02312AXM

CWDM-SFPGE-1591

Table 1-47 Technical specifications

Item	Description
Transceiver form factor	eSFP
Transmission speed	GE
Center wavelength (nm)	1591
Standards compliance	GE-CWDM
Connector type	LC
Applicable cable and maximum transmission distance	Single-mode fiber: 80 km
Transmit power (dBm)	0 to 5.0
Maximum receiver sensitivity (dBm)	-28.0
Overload power (dBm)	-9.0
Extinction ratio (dB)	8.5
Operating temperature	0°C to 70°C (32°F to 158°F)
Part number	02312AXK

CWDM-SFPGE-1611

Table 1-48 Technical specifications

Item	Description
Transceiver form factor	eSFP
Transmission speed	GE
Center wavelength (nm)	1611
Standards compliance	GE-CWDM
Connector type	LC
Applicable cable and maximum transmission distance	Single-mode fiber: 80 km
Transmit power (dBm)	0 to 5.0
Maximum receiver sensitivity (dBm)	-28.0
Overload power (dBm)	-9.0
Extinction ratio (dB)	8.5
Operating temperature	0°C to 70°C (32°F to 158°F)
Part number	02310LPJ

GE-DWDM eSFP Optical Modules

DWDM-SFPGE-1560-61

Table 1-49 Technical specifications

Item	Description
Transceiver form factor	eSFP
Transmission speed	GE
Center wavelength (nm)	1560.61
Standards compliance	GE-DWDM
Connector type	LC
Applicable cable and maximum transmission distance	Single-mode fiber: 120 km
Transmit power (dBm)	0 to 4.0
Maximum receiver sensitivity (dBm)	-28.0
Overload power (dBm)	-8.0
Extinction ratio (dB)	8.2
Operating temperature	0°C to 70°C (32°F to 158°F)
Part number	02310LLE

10GE SFP+ Optical Modules

SFP-10G-USR

Table 1-50 Technical specifications

Item	Description
Transceiver form factor	SFP+
Transmission speed	10GE
Center wavelength (nm)	850
Standards compliance	10GBASE-USR (non-standard)
Connector type	LC
Applicable cable and maximum transmission distance	Multimode fiber (OM3): 0.1 km
Transmit power (dBm)	-7.3 to -1.0
Maximum receiver sensitivity (dBm)	-10.7
Overload power (dBm)	0.5
Extinction ratio (dB)	3.0
Operating temperature	0°C to 70°C (32°F to 158°F)
Part number	02310MNW

OSXD22N00

Table 1-51 Technical Specifications

Item	Description
Transceiver form factor	SFP+
Transmission speed	10GE
Center wavelength (nm)	1310
Standards compliance	10GBASE-LRM
Connector type	LC
Applicable cable and maximum transmission distance	Multimode fiber (with modal bandwidth of 400 MHzkm and diameter of 50 μm): 0.1 km Multimode fiber (with modal bandwidth of 500 MHzkm and diameter of 62.5 μm): 0.22 km Multimode fiber (OM1, OM2, OM3): 0.22 km
Transmit power (dBm)	-6.5 to +0.5
Maximum receiver sensitivity (dBm)	-6.5
Overload power (dBm)	1.5
Extinction ratio (dB)	3.5
Operating temperature	0°C to 70°C (32°F to 158°F)
Part number	02310CRM

OMXD30000

Table 1-52 Technical Specifications

Item	Description
Transceiver form factor	SFP+
Transmission speed	10GE
Center wavelength (nm)	850
Standards compliance	10GBASE-SR
Connector type	LC
Applicable cable and maximum transmission distance	Multimode fiber (with modal bandwidth of 160 MHzkm and diameter of 62.5 μm): 0.026 km Multimode fiber (OM1): 0.033 km Multimode fiber (with modal bandwidth of 400 MHzkm and diameter of 50 μm): 0.066 km Multimode fiber (OM2): 0.082 km Multimode fiber (OM3): 0.3 km Multimode fiber (OM4): 0.4 km
Transmit power (dBm)	-7.3 to -1.0
Maximum receiver sensitivity (dBm)	-11.1
Overload power (dBm)	-1.0
Extinction ratio (dB)	3.0
Operating temperature	0°C to 70°C (32°F to 158°F)
Part number	02318169

SFP-10G-iLR

Table 1-53 Technical specifications

Item	Description
Transceiver form factor	SFP+
Transmission speed	10GE
Center wavelength (nm)	1310
Standards compliance	10GBASE-iLR (non-standard)
Connector type	LC
Applicable cable and maximum transmission distance	Single-mode fiber: 1.4 km
Transmit power (dBm)	-8.2 to +0.5
Maximum receiver sensitivity (dBm)	-14.4
Overload power (dBm)	0.5
Extinction ratio (dB)	3.5
Operating temperature	-40°C to +85°C (-40°F to +185°F)
Part number	02311BJJ

This module can only be used on a switch running V200R008C00 or a later version. A switch running an earlier version may fail to obtain information about this module.

OSX010000

Table 1-54 Technical Specifications

Item	Description
Transceiver form factor	SFP+
Transmission speed	10GE
Center wavelength (nm)	1310
Standards compliance	10GBASE-LR
Connector type	LC
Applicable cable and maximum transmission distance	Single-mode fiber: 10 km
Transmit power (dBm)	-8.2 to +0.5
Maximum receiver sensitivity (dBm)	-12.6
Overload power (dBm)	0.5
Extinction ratio (dB)	3.5
Operating temperature	0°C to 70°C (32°F to 158°F)
Part number	02318170

OSX040N01

Table 1-55 Technical Specifications

Item	Description
Transceiver form factor	SFP+
Transmission speed	10GE
Center wavelength (nm)	1550
Standards compliance	10GBASE-ER
Connector type	LC
Applicable cable and maximum transmission distance	Single-mode fiber: 40 km
Transmit power (dBm)	-4.7 to +4.0
Maximum receiver sensitivity (dBm)	-14.1
Overload power (dBm)	-1.0
Extinction ratio (dB)	3.0
Operating temperature	0°C to 70°C (32°F to 158°F)
Part number	02310CNF

SFP-10G-ER-1310

Table 1-56 Technical Specifications

Item	Description
Transceiver form factor	SFP+
Transmission speed	10GE
Center wavelength (nm)	1310
Standards compliance	Non-standard and compatible with the 10Gbase-ER
Connector type	LC
Applicable cable and maximum transmission distance	Single-mode fiber: 40 km
Transmit power (dBm)	-2.0 to +4.0
Maximum receiver sensitivity (dBm)	-20
Overload power (dBm)	-7.0
Extinction ratio (dB)	3.5
Operating temperature	0°C to 70°C (32°F to 158°F)
Part number	02311RLX

If the SFP-10G-ER-1310 is connected to a 10Gbase-ER standard optical module (1550nm, 10GE, 40km), the maximum transmission distance is only 20km due to different specifications such as wavelength and receiving sensitivity.

This module can only be used on a switch running V200R010C00 or a later version.

SFP-10G-ZR

Table 1-57 Technical specifications

Item	Description
Transceiver form factor	SFP+
Transmission speed	10GE
Center wavelength (nm)	1550
Standards compliance	10GBASE-ZR
Connector type	LC
Applicable cable and maximum transmission distance	Single-mode fiber: 80 km
Transmit power (dBm)	0 to 4.0
Maximum receiver sensitivity (dBm)	-24.0
Overload power (dBm)	-7.0
Extinction ratio (dB)	9
Operating temperature	0°C to 70°C (32°F to 158°F)
Part number	02310SNN

SFP-10G-BXU1 (Single-Fiber-Bidirectional Module)

Table 1-58 Technical specifications

Item	Description
Transceiver form factor	SFP+
Transmission speed	10GE
Center wavelength (nm)	Rx: 1330/Tx: 1270
Standards compliance	10GBASE-BX
Connector type	LC
Applicable cable and maximum transmission distance	Single-mode fiber: 10 km
Transmit power (dBm)	-8.2 to +0.5
Maximum receiver sensitivity (dBm)	-14.4
Overload power (dBm)	0.5
Extinction ratio (dB)	3.5
Operating temperature	-40°C to +85°C (-40°F to +185°F)
Part number	02310QBJ

Single-fiber bidirectional (BIDI) optical modules must be used in pairs. For example, SFP-10G-BXU1 must be used with SFP-10G-BXD1.

SFP-10G-BXD1 (Single-Fiber-Bidirectional Module)

Table 1-59 Technical specifications

Item	Description
Transceiver form factor	SFP+
Transmission speed	10GE
Center wavelength (nm)	Rx: 1270/Tx: 1330
Standards compliance	10GBASE-BX
Connector type	LC
Applicable cable and maximum transmission distance	Single-mode fiber: 10 km
Transmit power (dBm)	-8.2 to +0.5
Maximum receiver sensitivity (dBm)	-14.4
Overload power (dBm)	0.5
Extinction ratio (dB)	3.5
Operating temperature	-40°C to +85°C (-40°F to +185°F)
Part number	02310QDT

Single-fiber bidirectional (BIDI) optical modules must be used in pairs. For example, SFP-10G-BXD1 must be used with SFP-10G-BXU1.

SFP-10G-ER-SM1330-BIDI (Single-Fiber-Bidirectional Module)

Table 1-60 Technical specifications

Item	Description
Transceiver form factor	SFP+
Transmission speed	10GE
Center wavelength (nm)	Rx: 1270/Tx: 1330
Standards compliance	10GBASE-BX
Connector type	LC
Applicable cable and maximum transmission distance	Single-mode fiber: 40 km
Transmit power (dBm)	0 to 5
Maximum receiver sensitivity (dBm)	-18
Overload power (dBm)	-9
Extinction ratio (dB)	3.5
Operating temperature	0°C to 70°C (32°F to 158°F)
Part number	02311BJB

This module can only be used on a switch running V200R009C00 or a later version. A switch running an earlier version may fail to obtain information about this module.

Single-fiber bidirectional (BIDI) optical modules must be used in pairs. For example, SFP-10G-ER-SM1330-BIDI must be used with SFP-10G-ER-SM1270-BIDI.

SFP-10G-ER-SM1270-BIDI (Single-Fiber-Bidirectional Module)

Table 1-61 Technical specifications

Item	Description
Transceiver form factor	SFP+
Transmission speed	10GE
Center wavelength (nm)	Rx: 1330/Tx: 1270
Standards compliance	10GBASE-BX
Connector type	LC
Applicable cable and maximum transmission distance	Single-mode fiber: 40 km
Transmit power (dBm)	0 to 5
Maximum receiver sensitivity (dBm)	-18
Overload power (dBm)	-9
Extinction ratio (dB)	3.5
Operating temperature	0°C to 70°C (32°F to 158°F)
Part number	02311BJC

This module can only be used on a switch running V200R009C00 or a later version. A switch running an earlier version may fail to obtain information about this module.

Single-fiber bidirectional (BIDI) optical modules must be used in pairs. For example, SFP-10G-ER-SM1270-BIDI must be used with SFP-10G-ER-SM1330-BIDI.

10GE XFP Optical Modules

XFP-SX-MM850

Table 1-62 Technical specifications

Item	Description
Transceiver type	XFP
Transmission speed	10GE
Center wavelength (nm)	850
Standards compliance	10GBASE-SR
Connector type	LC
Applicable cable and maximum transmission distance	Multimode fiber (with modal bandwidth of 160 MHzkm and diameter of 62.5 μm): 0.026 km Multimode fiber (OM1): 0.033 km Multimode fiber (with modal bandwidth of 400 MHzkm and diameter of 50 μm): 0.066 km Multimode fiber (OM2): 0.082 km Multimode fiber (OM3): 0.3 km Multimode fiber (OM4): 0.4 km
Transmit power (dBm)	-7.3 to -1.3
Maximum receiver sensitivity (dBm)	-7.5
Overload power (dBm)	-1
Extinction ratio (dB)	3
Operating temperature	0°C to 70°C (32°F to 158°F)
Part number	02315176

XFP-STM64-LX-SM1310

Table 1-63 Technical specifications

Item	Description
Transceiver type	XFP
Transmission speed	10GE
Center wavelength (nm)	1310
Standards compliance	10GBASE-LR
Connector type	LC
Applicable cable and maximum transmission distance	Single-mode fiber: 10 km
Transmit power (dBm)	-6.0 to -1.0
Maximum receiver sensitivity (dBm)	-14.4
Overload power (dBm)	0.5
Extinction ratio (dB)	6
Operating temperature	0°C to 70°C (32°F to 158°F)
Part number	02315208

XFP-STM64-LH40-SM1550

Table 1-64 Technical specifications

Item	Description
Transceiver type	XFP
Transmission speed	10GE
Center wavelength (nm)	1550
Standards compliance	10GBASE-ER
Connector type	LC
Applicable cable and maximum transmission distance	Single-mode fiber: 40 km
Transmit power (dBm)	-1 to +2
Maximum receiver sensitivity (dBm)	-15
Overload power (dBm)	-1
Extinction ratio (dB)	8.2
Operating temperature	0°C to 70°C (32°F to 158°F)
Part number	02315209

XFP-STM64-SM1550-80km

Table 1-65 Technical specifications

Item	Description
Transceiver type	XFP
Transmission speed	10GE
Center wavelength (nm)	1550
Standards compliance	10GBASE-ZR
Connector type	LC
Applicable cable and maximum transmission distance	Single-mode fiber: 80 km
Transmit power (dBm)	0 to 4
Maximum receiver sensitivity (dBm)	-24
Overload power (dBm)	-7
Extinction ratio (dB)	9
Operating temperature	0°C to 70°C (32°F to 158°F)
Part number	02315143

10GE-CWDM SFP+ Optical Modules

SFP-10G-ZCW1471

Table 1-66 Technical specifications

Item	Description
Transceiver form factor	SFP+
Transmission speed	10GE
Center wavelength (nm)	1471
Standards compliance	10G-CWDM
Connector type	LC
Applicable cable and maximum transmission distance	Single-mode fiber: 70 km
Transmit power (dBm)	0 to 4.0
Maximum receiver sensitivity (dBm)	-23.0
Overload power (dBm)	-7.0
Extinction ratio (dB)	8.2
Operating temperature	0°C to 70°C (32°F to 158°F)
Part number	02310SSG

SFP-10G-ZCW1491

Table 1-67 Technical specifications

Item	Description
Transceiver form factor	SFP+
Transmission speed	10GE
Center wavelength (nm)	1491
Standards compliance	10G-CWDM
Connector type	LC
Applicable cable and maximum transmission distance	Single-mode fiber: 70 km
Transmit power (dBm)	0 to 4.0
Maximum receiver sensitivity (dBm)	-23.0
Overload power (dBm)	-7.0
Extinction ratio (dB)	8.2
Operating temperature	0°C to 70°C (32°F to 158°F)
Part number	02310SSF

SFP-10G-ZCW1511

Table 1-68 Technical specifications

Item	Description
Transceiver form factor	SFP+
Transmission speed	10GE
Center wavelength (nm)	1511
Standards compliance	10G-CWDM
Connector type	LC
Applicable cable and maximum transmission distance	Single-mode fiber: 70 km
Transmit power (dBm)	0 to 4.0
Maximum receiver sensitivity (dBm)	-23.0
Overload power (dBm)	-7.0
Extinction ratio (dB)	8.2
Operating temperature	0°C to 70°C (32°F to 158°F)
Part number	02310SSE

SFP-10G-ZCW1531

Table 1-69 Technical specifications

Item	Description
Transceiver form factor	SFP+
Transmission speed	10GE
Center wavelength (nm)	1531
Standards compliance	10G-CWDM
Connector type	LC
Applicable cable and maximum transmission distance	Single-mode fiber: 70 km
Transmit power (dBm)	0 to 4.0
Maximum receiver sensitivity (dBm)	-23.0
Overload power (dBm)	-7.0
Extinction ratio (dB)	8.2
Operating temperature	0°C to 70°C (32°F to 158°F)
Part number	02310SSD

SFP-10G-ZCW1551

Table 1-70 Technical specifications

Item	Description
Transceiver form factor	SFP+
Transmission speed	10GE
Center wavelength (nm)	1551
Standards compliance	10G-CWDM
Connector type	LC
Applicable cable and maximum transmission distance	Single-mode fiber: 70 km
Transmit power (dBm)	0 to 4.0
Maximum receiver sensitivity (dBm)	-23.0
Overload power (dBm)	-7.0
Extinction ratio (dB)	8.2
Operating temperature	0°C to 70°C (32°F to 158°F)
Part number	02310SSC

SFP-10G-ZCW1571

Table 1-71 Technical specifications

Item	Description
Transceiver form factor	SFP+
Transmission speed	10GE
Center wavelength (nm)	1571
Standards compliance	10G-CWDM
Connector type	LC
Applicable cable and maximum transmission distance	Single-mode fiber: 70 km
Transmit power (dBm)	0 to 4.0
Maximum receiver sensitivity (dBm)	-23.0
Overload power (dBm)	-7.0
Extinction ratio (dB)	8.2
Operating temperature	0°C to 70°C (32°F to 158°F)
Part number	02310SSB

SFP-10G-ZCW1591

Table 1-72 Technical specifications

Item	Description
Transceiver form factor	SFP+
Transmission speed	10GE
Center wavelength (nm)	1591
Standards compliance	10G-CWDM
Connector type	LC
Applicable cable and maximum transmission distance	Single-mode fiber: 70 km
Transmit power (dBm)	0 to 4.0
Maximum receiver sensitivity (dBm)	-23.0
Overload power (dBm)	-7.0
Extinction ratio (dB)	8.2
Operating temperature	0°C to 70°C (32°F to 158°F)
Part number	02310SSA

SFP-10G-ZCW1611

Table 1-73 Technical specifications

Item	Description
Transceiver form factor	SFP+
Transmission speed	10GE
Center wavelength (nm)	1611
Standards compliance	10G-CWDM
Connector type	LC
Applicable cable and maximum transmission distance	Single-mode fiber: 70 km
Transmit power (dBm)	0 to 4.0
Maximum receiver sensitivity (dBm)	-23.0
Overload power (dBm)	-7.0
Extinction ratio (dB)	8.2
Operating temperature	0°C to 70°C (32°F to 158°F)
Part number	02310SRY

10GE-CWDM XFP Optical Modules

CWDM-XFP10G-1471

Table 1-74 Technical specifications

Item	Description
Transceiver form factor	XFP
Transmission speed	10GE
Center wavelength (nm)	1471
Standards compliance	10G-CWDM
Connector type	LC
Applicable cable and maximum transmission distance	Single-mode fiber: 70 km
Transmit power (dBm)	0 to 3
Maximum receiver sensitivity (dBm)	-21
Overload power (dBm)	-9
Extinction ratio (dB)	8.2
Operating temperature	0°C to 70°C (32°F to 158°F)
Part number	02310LQS

CWDM-XFP10G-1491

Table 1-75 Technical specifications

Item	Description
Transceiver form factor	XFP
Transmission speed	10GE
Center wavelength (nm)	1491
Standards compliance	10G-CWDM
Connector type	LC
Applicable cable and maximum transmission distance	Single-mode fiber: 70 km
Transmit power (dBm)	0 to 3
Maximum receiver sensitivity (dBm)	-21
Overload power (dBm)	-9
Extinction ratio (dB)	8.2
Operating temperature	0°C to 70°C (32°F to 158°F)
Part number	02310LQU

CWDM-XFP10G-1511

Table 1-76 Technical specifications

Item	Description
Transceiver form factor	XFP
Transmission speed	10GE
Center wavelength (nm)	1511
Standards compliance	10G-CWDM
Connector type	LC
Applicable cable and maximum transmission distance	Single-mode fiber: 70 km
Transmit power (dBm)	0 to 3
Maximum receiver sensitivity (dBm)	-21
Overload power (dBm)	-9
Extinction ratio (dB)	8.2
Operating temperature	0°C to 70°C (32°F to 158°F)
Part number	02310LQV

CWDM-XFP10G-1531

Table 1-77 Technical specifications

Item	Description
Transceiver form factor	XFP
Transmission speed	10GE
Center wavelength (nm)	1531
Standards compliance	10G-CWDM
Connector type	LC
Applicable cable and maximum transmission distance	Single-mode fiber: 70 km
Transmit power (dBm)	0 to 3
Maximum receiver sensitivity (dBm)	-21
Overload power (dBm)	-9
Extinction ratio (dB)	8.2
Operating temperature	0°C to 70°C (32°F to 158°F)
Part number	02310LQX

CWDM-XFP10G-1551

Table 1-78 Technical specifications

Item	Description
Transceiver form factor	XFP
Transmission speed	10GE
Center wavelength (nm)	1551
Standards compliance	10G-CWDM
Connector type	LC
Applicable cable and maximum transmission distance	Single-mode fiber: 70 km
Transmit power (dBm)	0 to 3
Maximum receiver sensitivity (dBm)	-21
Overload power (dBm)	-9
Extinction ratio (dB)	8.2
Operating temperature	0°C to 70°C (32°F to 158°F)
Part number	02310LQY

CWDM-XFP10G-1571

Table 1-79 Technical specifications

Item	Description
Transceiver form factor	XFP
Transmission speed	10GE
Center wavelength (nm)	1571
Standards compliance	10G-CWDM
Connector type	LC
Applicable cable and maximum transmission distance	Single-mode fiber: 70 km
Transmit power (dBm)	0 to 3
Maximum receiver sensitivity (dBm)	-21
Overload power (dBm)	-9
Extinction ratio (dB)	8.2
Operating temperature	0°C to 70°C (32°F to 158°F)
Part number	02310LRB

CWDM-XFP10G-1591

Table 1-80 Technical specifications

Item	Description
Transceiver form factor	XFP
Transmission speed	10GE
Center wavelength (nm)	1591
Standards compliance	10G-CWDM
Connector type	LC
Applicable cable and maximum transmission distance	Single-mode fiber: 70 km
Transmit power (dBm)	0 to 3
Maximum receiver sensitivity (dBm)	-21
Overload power (dBm)	-9
Extinction ratio (dB)	8.2
Operating temperature	0°C to 70°C (32°F to 158°F)
Part number	02310LRC

CWDM-XFP10G-1611

Table 1-81 Technical specifications

Item	Description
Transceiver form factor	XFP
Transmission speed	10GE
Center wavelength (nm)	1611
Standards compliance	10G-CWDM
Connector type	LC
Applicable cable and maximum transmission distance	Single-mode fiber: 70 km
Transmit power (dBm)	0 to 3
Maximum receiver sensitivity (dBm)	-21
Overload power (dBm)	-9
Extinction ratio (dB)	8.2
Operating temperature	0°C to 70°C (32°F to 158°F)
Part number	02310LRE

10GE-DWDM SFP+ Optical Modules

SFP-10G-ZDWT

Table 1-82 Technical specifications

Item	Description
Transceiver form factor	SFP+
Transmission speed	10GE
Center wavelength (nm)	1529.16 to 1560.61
Standards compliance	10GBASE-DWDM
Connector type	LC
Applicable cable and maximum transmission distance	Single-mode fiber: 60 km
Transmit power (dBm)	-1 to +3
Maximum receiver sensitivity (dBm)	-24
Overload power (dBm)	-1
Extinction ratio (dB)	8.2
Operating temperature	0°C to 70°C (32°F to 158°F)
Part number	02310YUT

This module can only be used on a switch running V200R009C00 or a later version. A switch running an earlier version may fail to obtain information about this module.

The optical module takes a long time to start. Therefore, a low optical power alarm may be generated when such an optical module is installed on a switch.

10GE-DWDM XFP Optical Modules

DWDM-XFP10G-1533-47

Table 1-83 Technical specifications

Item	Description
Transceiver form factor	XFP
Transmission speed	10GE
Center wavelength (nm)	1533.47
Standards compliance	10G-DWDM
Connector type	LC
Applicable cable and maximum transmission distance	Single-mode fiber: 80 km
Transmit power (dBm)	-1 to +3
Maximum receiver sensitivity (dBm)	-24
Overload power (dBm)	-9
Extinction ratio (dB)	8.2
Operating temperature	0°C to 70°C (32°F to 158°F)
Part number	02310LRN

DWDM-XFP10G-1534-25

Table 1-84 Technical specifications

Item	Description
Transceiver form factor	XFP
Transmission speed	10GE
Center wavelength (nm)	1534.25
Standards compliance	10G-DWDM
Connector type	LC
Applicable cable and maximum transmission distance	Single-mode fiber: 80 km
Transmit power (dBm)	-1 to +3
Maximum receiver sensitivity (dBm)	-24
Overload power (dBm)	-9
Extinction ratio (dB)	8.2
Operating temperature	0°C to 70°C (32°F to 158°F)
Part number	02310LRM

DWDM-XFP10G-1535-04

Table 1-85 Technical specifications

Item	Description
Transceiver form factor	XFP
Transmission speed	10GE
Center wavelength (nm)	1535.04
Standards compliance	10G-DWDM
Connector type	LC
Applicable cable and maximum transmission distance	Single-mode fiber: 80 km
Transmit power (dBm)	-1 to +3
Maximum receiver sensitivity (dBm)	-24
Overload power (dBm)	-9
Extinction ratio (dB)	8.2
Operating temperature	0°C to 70°C (32°F to 158°F)
Part number	02310LRL

DWDM-XFP10G-1552-52

Table 1-86 Technical specifications

Item	Description
Transceiver form factor	XFP
Transmission speed	10GE
Center wavelength (nm)	1552.52
Standards compliance	10G-DWDM
Connector type	LC
Applicable cable and maximum transmission distance	Single-mode fiber: 80 km
Transmit power (dBm)	-1 to +3
Maximum receiver sensitivity (dBm)	-24
Overload power (dBm)	-9
Extinction ratio (dB)	8.2
Operating temperature	0°C to 70°C (32°F to 158°F)
Part number	02310LRK

DWDM-XFP10G-1553-33

Table 1-87 Technical specifications

Item	Description
Transceiver form factor	XFP
Transmission speed	10GE
Center wavelength (nm)	1553.33
Standards compliance	10G-DWDM
Connector type	LC
Applicable cable and maximum transmission distance	Single-mode fiber: 80 km
Transmit power (dBm)	-1 to +3
Maximum receiver sensitivity (dBm)	-24
Overload power (dBm)	-9
Extinction ratio (dB)	8.2
Operating temperature	0°C to 70°C (32°F to 158°F)
Part number	02310LRJ

DWDM-XFP10G-1554-13

Table 1-88 Technical specifications

Item	Description
Transceiver form factor	XFP
Transmission speed	10GE
Center wavelength (nm)	1554.13
Standards compliance	10G-DWDM
Connector type	LC
Applicable cable and maximum transmission distance	Single-mode fiber: 80 km
Transmit power (dBm)	-1 to +3
Maximum receiver sensitivity (dBm)	-24
Overload power (dBm)	-9
Extinction ratio (dB)	8.2
Operating temperature	0°C to 70°C (32°F to 158°F)
Part number	02310LRH

DWDM-XFP10G-1530-33

Table 1-89 Technical specifications

Item	Description
Transceiver form factor	XFP
Transmission speed	10GE
Center wavelength (nm)	1530.33
Standards compliance	10G-DWDM
Connector type	LC
Applicable cable and maximum transmission distance	Single-mode fiber: 80 km
Transmit power (dBm)	-1 to +3
Maximum receiver sensitivity (dBm)	-24
Overload power (dBm)	-9
Extinction ratio (dB)	8.2
Operating temperature	0°C to 70°C (32°F to 158°F)
Part number	02310LPW

DWDM-XFP10G-1549-32

Table 1-90 Technical specifications

Item	Description
Transceiver form factor	XFP
Transmission speed	10GE
Center wavelength (nm)	1549.32
Standards compliance	10G-DWDM
Connector type	LC
Applicable cable and maximum transmission distance	Single-mode fiber: 80 km
Transmit power (dBm)	-1 to +3
Maximum receiver sensitivity (dBm)	-24
Overload power (dBm)	-9
Extinction ratio (dB)	8.2
Operating temperature	0°C to 70°C (32°F to 158°F)
Part number	02310LPV

DWDM-XFP10G-1531-12

Table 1-91 Technical specifications

Item	Description
Transceiver form factor	XFP
Transmission speed	10GE
Center wavelength (nm)	1531.12
Standards compliance	10G-DWDM
Connector type	LC
Applicable cable and maximum transmission distance	Single-mode fiber: 80 km
Transmit power (dBm)	-1 to +3
Maximum receiver sensitivity (dBm)	-24
Overload power (dBm)	-9
Extinction ratio (dB)	8.2
Operating temperature	0°C to 70°C (32°F to 158°F)
Part number	02310LPU

DWDM-XFP10G-1531-90

Table 1-92 Technical specifications

Item	Description
Transceiver form factor	XFP
Transmission speed	10GE
Center wavelength (nm)	1531.90
Standards compliance	10G-DWDM
Connector type	LC
Applicable cable and maximum transmission distance	Single-mode fiber: 80 km
Transmit power (dBm)	-1 to +3
Maximum receiver sensitivity (dBm)	-24
Overload power (dBm)	-9
Extinction ratio (dB)	8.2
Operating temperature	0°C to 70°C (32°F to 158°F)
Part number	02310LPS

DWDM-XFP10G-1550-12

Table 1-93 Technical specifications

Item	Description
Transceiver form factor	XFP
Transmission speed	10GE
Center wavelength (nm)	1550.12
Standards compliance	10G-DWDM
Connector type	LC
Applicable cable and maximum transmission distance	Single-mode fiber: 80 km
Transmit power (dBm)	-1 to +3
Maximum receiver sensitivity (dBm)	-24
Overload power (dBm)	-9
Extinction ratio (dB)	8.2
Operating temperature	0°C to 70°C (32°F to 158°F)
Part number	02310LPQ

DWDM-XFP10G-1550-92

Table 1-94 Technical specifications

Item	Description
Transceiver form factor	XFP
Transmission speed	10GE
Center wavelength (nm)	1550.92
Standards compliance	10G-DWDM
Connector type	LC
Applicable cable and maximum transmission distance	Single-mode fiber: 80 km
Transmit power (dBm)	-1 to +3
Maximum receiver sensitivity (dBm)	-24
Overload power (dBm)	-9
Extinction ratio (dB)	8.2
Operating temperature	0°C to 70°C (32°F to 158°F)
Part number	02310LPP

DWDM-XFP10G-1532-68

Table 1-95 Technical specifications

Item	Description
Transceiver form factor	XFP
Transmission speed	10GE
Center wavelength (nm)	1532.68
Standards compliance	10G-DWDM
Connector type	LC
Applicable cable and maximum transmission distance	Single-mode fiber: 80 km
Transmit power (dBm)	-1 to +3
Maximum receiver sensitivity (dBm)	-24
Overload power (dBm)	-9
Extinction ratio (dB)	8.2
Operating temperature	0°C to 70°C (32°F to 158°F)
Part number	02310LQP

DWDM-XFP10G-1551-72

Table 1-96 Technical specifications

Item	Description
Transceiver form factor	XFP
Transmission speed	10GE
Center wavelength (nm)	1551.72
Standards compliance	10G-DWDM
Connector type	LC
Applicable cable and maximum transmission distance	Single-mode fiber: 80 km
Transmit power (dBm)	-1 to +3
Maximum receiver sensitivity (dBm)	-24
Overload power (dBm)	-9
Extinction ratio (dB)	8.2
Operating temperature	0°C to 70°C (32°F to 158°F)
Part number	02310LQN

DWDM-XFP10G-1529-55

Table 1-97 Technical specifications

Item	Description
Transceiver form factor	XFP
Transmission speed	10GE
Center wavelength (nm)	1529.55
Standards compliance	10G-DWDM
Connector type	LC
Applicable cable and maximum transmission distance	Single-mode fiber: 80 km
Transmit power (dBm)	-1 to +3
Maximum receiver sensitivity (dBm)	-24
Overload power (dBm)	-9
Extinction ratio (dB)	8.2
Operating temperature	0°C to 70°C (32°F to 158°F)
Part number	02310LQL

DWDM-XFP10G-1548-51

Table 1-98 Technical specifications

Item	Description
Transceiver form factor	XFP
Transmission speed	10GE
Center wavelength (nm)	1548.51
Standards compliance	10G-DWDM
Connector type	LC
Applicable cable and maximum transmission distance	Single-mode fiber: 80 km
Transmit power (dBm)	-1 to +3
Maximum receiver sensitivity (dBm)	-24
Overload power (dBm)	-9
Extinction ratio (dB)	8.2
Operating temperature	0°C to 70°C (32°F to 158°F)
Part number	02310LQK

40GE QSFP+ Optical Modules

QSFP-40G-SR4

Table 1-99 Technical specifications

Item	Description
Transceiver form factor	QSFP+
Transmission speed	40GE
Center wavelength (nm)	850
Standards compliance	40GBASE-SR4
Connector type	MPO/PC (8-strand or 12-strand, type B, female connector)
Applicable cable and maximum transmission distance	Multimode fiber (OM3): 0.1 km Multimode fiber (OM4): 0.15 km
Transmit power (dBm)	-7.6 to +2.4
Maximum receiver sensitivity (dBm)	-5.4
Overload power (dBm)	2.4
Extinction ratio (dB)	3.0
Operating temperature	0°C to 70°C (32°F to 158°F)
Part number	02310MHQ

QSFP-40G-iSR4

Table 1-100 Technical specifications

Item	Description
Transceiver form factor	QSFP+
Transmission speed	40GE
Center wavelength (nm)	850
Standards compliance	40GBASE-SR4 40GBASE-iSR4 (non-standard)
Connector type	MPO/PC (8-strand or 12-strand, type B, female connector)
Applicable cable and maximum transmission distance	Multimode fiber (OM3): 0.1 km Multimode fiber (OM4): 0.15 km
Transmit power (dBm)	-7.6 to +0.5
Maximum receiver sensitivity (dBm)	-9.5
Overload power (dBm)	2.4
Extinction ratio (dB)	3.0
Operating temperature	0°C to 70°C (32°F to 158°F)
Part number	02310MHR

This module can connect a 40GE port to four 10GE ports using a 1-to-4 cable.

QSFP-40G-eSR4

Table 1-101 Technical specifications

Item	Description
Transceiver form factor	QSFP+
Transmission speed	40GE
Center wavelength (nm)	850
Standards compliance	40GBASE-eSR4 (non-standard)
Connector type	MPO/PC (8-strand or 12-strand, type B, female connector)
Applicable cable and maximum transmission distance	Multimode fiber (with modal bandwidth of 160 MHzkm and diameter of 62.5 μm): 0.026 km Multimode fiber (OM1): 0.033 km Multimode fiber (with modal bandwidth of 400 MHzkm and diameter of 50 μm): 0.066 km Multimode fiber (OM2): 0.082 km Multimode fiber (OM3): 0.3 km Multimode fiber (OM4): 0.4 km
Transmit power (dBm)	-7.6 to +0.5
Maximum receiver sensitivity (dBm)	-5.4
Overload power (dBm)	2.4
Extinction ratio (dB)	3.0
Operating temperature	0°C to 70°C (32°F to 158°F)
Part number	02310RMB

This module can connect a 40GE port to four 10GE ports using a 1-to-4 cable.

QSFP-40G-iSM4

Table 1-102 Technical specifications

Item	Description
Transceiver form factor	QSFP+
Transmission speed	40GE
Center wavelength (nm)	1310
Standards compliance	40GBASE-iSM4 (non-standard)
Connector type	MPO/APC (8-strand or 12-strand, type B, female connector)
Applicable cable and maximum transmission distance	Single-mode fiber: 1.4 km
Transmit power (dBm)	-8.2 to +0.5
Maximum receiver sensitivity (dBm)	-11.5
Overload power (dBm)	0.5
Extinction ratio (dB)	3.5
Operating temperature	0°C to 70°C (32°F to 158°F)
Part number	02311DRW

This module can connect a 40GE port to four 10GE ports using a 1-to-4 cable.

This module can only be used on a switch running V200R009C00 or a later version. A switch running an earlier version may fail to obtain information about this module.

QSFP-40G-eSM4

Table 1-103 Technical specifications

Item	Description
Transceiver form factor	QSFP+
Transmission speed	40GE
Center wavelength (nm)	1310
Standards compliance	40GBASE-eSM4 (non-standard)
Connector type	MPO/APC (8-strand or 12-strand, type B, female connector)
Applicable cable and maximum transmission distance	Single-mode fiber: 10 km
Transmit power (dBm)	-8.2 to +0.5
Maximum receiver sensitivity (dBm)	-12.6
Overload power (dBm)	0.5
Extinction ratio (dB)	3.5
Operating temperature	0°C to 70°C
Part number	02311DTR

This module can connect a 40GE port to four 10GE ports using a 1-to-4 cable.

This module can only be used on a switch running V200R010C00 or a later version. A switch running an earlier version may fail to obtain information about this module.

QSFP-40G-LX4

Table 1-104 Technical specifications

Item	Description
Transceiver form factor	QSFP+
Transmission speed	40GE
Center wavelength (nm)	1271, 1291, 1311, 1331
Standards compliance	40GBASE-LX4
Connector type	LC
Applicable cable and maximum transmission distance	Single-mode fiber: 2 km Multimode fiber (OM3): 0.15 km
Transmit power (dBm)	-7.0 to +2.3
Maximum receiver sensitivity (dBm)	-11.5
Overload power (dBm)	2.3
Extinction ratio (dB)	3.5
Operating temperature	0°C to 70°C (32°F to 158°F)
Part number	02311HNP

When QSFP-40G-LX4 optical modules use multimode fibers, the fibers cannot be connected through multiple optical distribution frames (ODFs).

This module can only be used on a switch running V200R009C00 or a later version. A switch running an earlier version may fail to obtain information about this module.

QSFP-40G-LR4

Table 1-105 Technical specifications

Item	Description
Transceiver form factor	QSFP+
Transmission speed	40GE
Center wavelength (nm)	1271, 1291, 1311, 1331
Standards compliance	40GBASE-LR4
Connector type	LC
Applicable cable and maximum transmission distance	Single-mode fiber: 10 km
Transmit power (dBm)	-7.0 to +2.3
Maximum receiver sensitivity (dBm)	-11.5
Overload power (dBm)	3.3
Extinction ratio (dB)	3.5
Operating temperature	0°C to 70°C (32°F to 158°F)
Part number	02310MHS

QSFP-40G-ER4

Table 1-106 Technical specifications

Item	Description
Transceiver form factor	QSFP+
Transmission speed	40GE
Center wavelength (nm)	1271, 1291, 1311, 1331
Standards compliance	40GBASE-ER4
Connector type	LC
Applicable cable and maximum transmission distance	Single-mode fiber: 40 km
Transmit power (dBm)	-2.7 to +4.5
Maximum receiver sensitivity (dBm)	-19.5
Overload power (dBm)	-4.5
Extinction ratio (dB)	5.5
Operating temperature	0°C to 70°C (32°F to 158°F)
Part number	02311BKT

This module can only be used on a switch running V200R008C00 or a later version. A switch running an earlier version may fail to obtain information about this module.

QSFP-40G-SR-BD

Table 1-107 Technical specifications

Item	Description
Transceiver form factor	QSFP+
Transmission speed	40GE
Center wavelength (nm)	850, 900
Standards compliance	40GBASE-BIDI (non-standard)
Connector type	LC
Applicable cable and maximum transmission distance	Multimode fiber (OM3): 0.1 km Multimode fiber (OM4): 0.15 km
Transmit power (dBm)	-4 to +5
Maximum receiver sensitivity (dBm)	-4.5
Overload power (dBm)	5
Extinction ratio (dB)	4.5
Operating temperature	10°C to 70°C (50°F to 158°F) NOTICE: Temporary interruption or packet loss may occur on ports of the switch if the operating temperature is below 10°C (50°F).
Part number	02311FPA

QSFP-40G-SR-BD optical modules cannot be used for CSS or stack connection and do not support some digital diagnostic monitoring (DDM) function.

This module can only be used on a switch running V200R009C00 or a later version. A switch running an earlier version may fail to obtain information about this module.

QSFP-40G-SDLC-PAM

Table 1-108 Technical specifications

Item	Description
Transceiver form factor	QSFP+
Transmission speed	40GE
Center wavelength (nm)	850
Standards compliance	40GBASE-PAM4 (non-standard)
Connector type	LC
Applicable cable and maximum transmission distance	Multimode fiber (OM3): 100 m Multimode fiber (OM4): 150 m
Transmit power (dBm)	-2.5 to +2.4
Maximum receiver sensitivity (dBm)	-8.0
Overload power (dBm)	2.4
Extinction ratio (dB)	3
Operating temperature	0°C to 70°C (32°F to 158°F)
Part number	02311PUU

This module can only be used on a switch running V200R011C10 or a later version.

QSFP-40G-eSDLC-PAM

Table 1-109 Technical specifications

Item	Description
Transceiver form factor	QSFP+
Transmission speed	40GE
Center wavelength (nm)	850
Standards compliance	40GBASE-ePAM4 (non-standard)
Connector type	LC
Applicable cable and maximum transmission distance	Multimode fiber (OM3): 100 m Multimode fiber (OM4): 300 m
Transmit power (dBm)	-2 to +2.4
Maximum receiver sensitivity (dBm)	-8.0
Overload power (dBm)	2.4
Extinction ratio (dB)	3
Operating temperature	0°C to 70°C (32°F to 158°F)
Part number	02311QTR

This module can only be used on a switch running V200R011C10 or a later version.

40GE CFP Optical Modules

CFP-40G-SR4

Table 1-110 Technical specifications

Item	Description
Transceiver form factor	CFP
Transmission speed	40GE
Center wavelength (nm)	850
Standards compliance	40GBASE-SR4
Connector type	MPO/PC (8-strand or 12-strand, type B, female connector)
Applicable cable and maximum transmission distance	Multimode fiber (OM3): 0.1 km Multimode fiber (OM4): 0.15 km
Transmit power (dBm)	-7.6 to +2.4
Maximum receiver sensitivity (dBm)	-9.5
Overload power (dBm)	2.4
Extinction ratio (dB)	3
Operating temperature	0°C to 70°C (32°F to 158°F)
Part number	02311CXC

This module can connect a 40GE port to four 10GE ports using a 1-to-4 cable.

CFP-40G-LR4

Table 1-111 Technical specifications

Item	Description
Transceiver form factor	CFP
Transmission speed	40GE
Center wavelength (nm)	1271, 1291, 1311, 1331
Standards compliance	40GBASE-LR4
Connector type	LC
Applicable cable and maximum transmission distance	Single-mode fiber: 10 km
Transmit power (dBm)	-4 to +3.5
Maximum receiver sensitivity (dBm)	-11.5
Overload power (dBm)	3.5
Extinction ratio (dB)	3.5
Operating temperature	0°C to 70°C (32°F to 158°F)
Part number	02310YTF

CFP-40G-ER4

Table 1-112 Technical specifications

Item	Description
Transceiver form factor	CFP
Transmission speed	40GE
Center wavelength (nm)	1271, 1291, 1311, 1331
Standards compliance	40GBASE-ER4
Connector type	LC
Applicable cable and maximum transmission distance	Single-mode fiber: 40 km
Transmit power (dBm)	-1.1 to +3.8
Maximum receiver sensitivity (dBm)	-18
Overload power (dBm)	3.8
Extinction ratio (dB)	7
Operating temperature	0°C to 70°C (32°F to 158°F)
Part number	02310YTH

CFP-40G-ZR4

Table 1-113 Technical specifications

Item	Description
Transceiver form factor	CFP
Transmission speed	40GE
Center wavelength (nm)	1531.12, 1537.4, 1543.73, 1550.12
Standards compliance	40GBASE-ZR4
Connector type	LC
Applicable cable and maximum transmission distance	Single-mode fiber: 80 km
Transmit power (dBm)	0 to +4.5
Maximum receiver sensitivity (dBm)	-22
Overload power (dBm)	-7
Extinction ratio (dB)	9
Operating temperature	0°C to 70°C (32°F to 158°F)
Part number	02311KAH

This module can only be used on a switch running V200R009C00 or a later version. A switch running an earlier version may fail to obtain information about this module.

100GE CFP Optical Modules

CFP-100G-SR10

Table 1-114 Technical specifications

Item	Description
Transceiver form factor	CFP
Transmission speed	100GE
Center wavelength (nm)	850
Standards compliance	100GBASE-SR10
Connector type	MPO/PC (24-strand, type B, female connector)
Applicable cable and maximum transmission distance	Multimode fiber (OM2): 0.03 km Multimode fiber (OM3): 0.1 km Multimode fiber (OM4): 0.15 km
Transmit power (dBm)	-7.6 to +2.4
Maximum receiver sensitivity (dBm)	-5.4
Overload power (dBm)	2.4
Extinction ratio (dB)	3
Operating temperature	0°C to 70°C (32°F to 158°F)
Part number	02310YTB

This module can connect a 100GE port to two 40GE ports using a 1-to-2 cable or to ten 10GE ports using a 1-to-10 cable.

CFP-100G-LR4

Table 1-115 Technical specifications

Item	Description
Transceiver form factor	CFP

Enterprise

Huawei Cloud

Carrier

Consumer

Corporate

Optical Modules for Huawei S Series Switches

Important Notes About Using Optical Modules Certified for Huawei Switches

How to Identify Huawei-Certified Switch Optical Modules

10GE or Lower Speed Optical Modules

40GE and 100GE Optical Modules

Risks of Using Non-Huawei-Certified Switch Optical Modules

Understanding Optical Modules

What Is an Optical Module

Types of Optical Modules

Parameter Description

How to View Optical Module Parameters

Viewing the Hardware Description

Using a Command

Rules for Optical Module Interoperation

Interoperation Rules

Standards Description

Interoperability of 40GE and 100GE Optical Modules

Optical Modules Supported by Huawei S Series Switches

FE SFP/eSFP Optical Modules

SFP-FE-SX-MM1310

eSFP-FE-LX-SM1310

S-SFP-FE-LH40-SM1310

S-SFP-FE-LH80-SM1550

SFP-FE-LX-SM1310-BIDI (Single-Fiber-Bidirectional Module)

SFP-FE-LX-SM1550-BIDI (Single-Fiber-Bidirectional Module)

GE eSFP Optical Modules

eSFP-GE-SX-MM850

SFP-GE-LX-SM1310

S-SFP-GE-LH40-SM1310

S-SFP-GE-LH40-SM1550

S-SFP-GE-LH80-SM1550

eSFP-GE-ZX100-SM1550

SFP-GE-LX-SM1310-BIDI (Single-Fiber-Bidirectional Module)

SFP-GE-LX-SM1490-BIDI (Single-Fiber-Bidirectional Module)

LE2MGSC40DE0 (Single-Fiber-Bidirectional Module)

LE2MGSC40ED0 (Single-Fiber-Bidirectional Module)

SFP-GE-ZBXD1 (Single-Fiber-Bidirectional Module)

SFP-GE-ZBXU1 (Single-Fiber-Bidirectional Module)

SFP-GE-BXU1-SC (Single-Fiber-Bidirectional Module)

GE CSFP Optical Modules

CSFP-GE-FE-BXD1

CSFP-GE-FE-BIDI2

CSFP-GE-FE-BIDI4

GE-CWDM eSFP Optical Modules

CWDM-SFPGE-1471

CWDM-SFPGE-1491

CWDM-SFPGE-1511

CWDM-SFPGE-1531

CWDM-SFPGE-1551

CWDM-SFPGE-1571

CWDM-SFPGE-1591

CWDM-SFPGE-1611

GE-CWDM eSFP Optical Modules (Used Only in the OADM scenario)

CWDM-SFPGE-1271

CWDM-SFPGE-1291

CWDM-SFPGE-1311

CWDM-SFPGE-1331

CWDM-SFPGE-1351

CWDM-SFPGE-1371

CWDM-SFPGE-1391

CWDM-SFPGE-1411

CWDM-SFPGE-1431

CWDM-SFPGE-1451

CWDM-SFPGE-1471

CWDM-SFPGE-1491

CWDM-SFPGE-1511

CWDM-SFPGE-1531

CWDM-SFPGE-1551

CWDM-SFPGE-1571

CWDM-SFPGE-1591

CWDM-SFPGE-1611

GE-DWDM eSFP Optical Modules

DWDM-SFPGE-1560-61

10GE SFP+ Optical Modules

SFP-10G-USR