AP Wired Port Profile

Procedure

• Create an AP wired port profile.
  1. Choose Configuration > Wireless Services > Profile > AP > AP Wired Port Profile. The AP Wired Port Profile List page is displayed.
  2. Click Create. The Create AP Wired Port Profile page is displayed.
  3. Enter the name of the new AP wired port profile in Profile name.

     To copy all parameters from another profile to the new profile, select the name of the profile in Copy parameters from other profiles. If None is selected, parameters are not copied from another profile.

  4. Click OK. The parameter setting page of the new AP wired port profile is displayed.
  5. Set parameters for creating an AP wired port profile. Table 9-32 describes the parameters for creating an AP wired port profile.

     
     
     

     Table 9-32 Parameters for creating an AP wired port profile

     Parameter		Description
     AP Wired Port Profile		Name of the AP wired port profile, which cannot be modified.
     Enable Eth-trunk		Whether to enable Eth-Trunk.
     Port description		Port description.
     Port mode		Operating mode of a wired interface. None: default mode Root: root mode Endpoint: endpoint mode Middle: middle mode
     User isolation mode		User isolation mode on a wired interface. This parameter can be configured only when Port mode is set to Endpoint.
     STP		Whether to enable STP on the wired interface.
     STP-triggered port shutdown		Whether STP-triggered port shutdown is enabled on the AP's wired interface. This parameter can be configured only when STP is set to ON.
     Port recovery time (s)		Auto-recovery interval for an AP's wired interface on which the STP-triggered port shutdown function is enabled. This parameter can be configured only when STP-triggered port shutdown is set to ON.
     DHCP trusted port		Whether to enable the DHCP trusted port function.
     ND trusted port		Whether to enable the ND trusted port function.
     IGMP Snooping		Whether to enable the IGMP Snooping function.
     MLD Snooping		Whether to enable the MLD Snooping function.
     Address learning		Whether terminal address learning is enabled on the AP's wired interface.
     IP packet binding check		Whether IP packet binding check is enabled on the AP's wired interface.
     ARP packet binding check		Whether dynamic ARP inspection (DAI) is enabled on the AP's wired interface.
     Port PVID		PVID of the wired interface. When receiving an untagged packet from a peer device, the AP's wired interface adds a VLAN tag to the packet. After the PVID is configured on the wired interface, the interface adds the PVID to all the received untagged packets.
     Added VLAN ID		ID of the VLAN to which the wired interface is added. An interface can join a VLAN in tagged or untagged mode.
     Packet Filtering
     Inbound ACL	Packet Filtering Type	Type of incoming packets (IPv4 or IPv6) to be filtered based on an ACL by an AP's wired interface.
     	IPv4/IPv6 ACL	ACL for filtering incoming packets. Click , and select a desired ACL from the inbound ACL list.
     Outbound ACL	Packet Filtering Type	Type of outgoing packets (IPv4 or IPv6) to be filtered based on an ACL by an AP's wired interface.
     	IPv4/IPv6 ACL	ACL for filtering outgoing packets. Click , and select a desired ACL from the outbound ACL list.
     Re-marking
     Re-marking Incoming Packets	Packet Re-marking Type	Type of incoming packets (IPv4 or IPv6) to be re-marked based on an ACL by an AP's wired interface.
     	IPv4/IPv6 ACL	ACL for re-marking incoming packets. Click , and select a desired ACL from the inbound ACL list.
     	Re-marking Type	Packet re-marking type.
     	Re-marking Packets	Preference of re-marked packets.
     Re-marking Outgoing Packets	Packet Re-marking Type	Type of outgoing packets (IPv4 or IPv6) to be re-marked based on an ACL by an AP's wired interface.
     	IPv4/IPv6 ACL	ACL for re-marking outgoing packets. Click , and select a desired ACL from the outbound ACL list.
     	Re-marking Type	Packet re-marking type.
     	Re-marking Packets	Preference of re-marked packets.
     Port Security Parameters in this area can be configured only when Port mode is set to Endpoint.
     Port security		Whether to enable the port security function.
     Maximum of sticky MAC addresses		Maximum number of secure MAC addresses that can be learned by an interface.
     Protection action		Port security action.
     Maintaining the MAC address after a reset		Whether to enable the MAC address reservation function after the reset.
     Storm Control
     Broadcast packet rate limit (pps)		Maximum broadcast traffic volume allowed on the AP's wired interface.
     Unicast packet rate limit (pps)		Maximum unknown unicast traffic volume allowed the AP's wired interface.
     Multicast packet rate limit (pps)		Maximum multicast traffic volume allowed on the AP's wired interface.

     By default, the working modes of APs' wired interfaces vary depending on the AP models.

     Table 9-33 Working modes of APs' wired interfaces

     AP Model	root	endpoint	middle
     Common APs (except AirEngine series APs)	GE port Eth-Trunk interface	Ethernet port	-
     Central APs (except AirEngine series APs)	Uplink 10GE/GE port	-	Downlink GE port
     R230D	Ethernet port	-	-
     R240D and AP2051DN-L-S	GE port	Ethernet port	-
     R250D, R250D-E, AP2050DN, AP5510-W-GP, AP2050DN-S, AP2050DN-E, AP2051DN, AP2051DN-S, AP2051DN-E, R251D, R251D-E	Uplink GE port	Downlink GE port	-
     R450D and AirEngine 5760-10	GE port	-	-
     AirEngine series indoor settled APs (except AirEngine 5760-10)	All interfaces (including Eth-Trunk interfaces)	-	-
     AirEngine series indoor settled APs (except AirEngine 5760-10)	All interfaces (including Eth-Trunk interfaces)	-	-
     AirEngine series outdoor APs	All interfaces (including Eth-Trunk interfaces)	-	-
     AirEngine series wall plate APs and RUs	Uplink port	Downlink port	-

  6. Click Apply. In the Info dialog box that is displayed, click OK.
• Modify an AP wired port profile.
  1. Choose Configuration > Wireless Services > Profile > AP > AP Wired Port Profile. The AP Wired Port Profile List page is displayed.
  2. Click the name of the AP wired port profile that you want to modify. The AP Wired Port Profile page is displayed.
  3. Modify parameters of the AP wired port profile. Table 9-32 describes the parameters for modifying an AP wired port profile.
  4. Click Apply. In the Info dialog box that is displayed, click OK.
• Delete an AP wired port profile.
  1. Choose Configuration > Wireless Services > Profile > AP > AP Wired Port Profile. The AP Wired Port Profile List page is displayed.
  2. Select the profile that you want to delete and click Delete. In the Confirm dialog box that is displayed, click OK.
• Display the profile reference relationship.
  1. Choose Configuration > Wireless Services > Profile > AP > AP Wired Port Profile. The AP Wired Port Profile List page is displayed.
  2. Select the profile of which you want to display the reference relationship and click Display Reference Relationship. The system displays the types and names of the objects that reference the profile.

     Click Hide Reference Relationship. The system hides the displayed results.

• Configure the profiles that are referenced by the AP wired port profile.
  1. Choose Configuration > Wireless Services > Profile > AP > AP Wired Port Profile. The AP Wired Port Profile List page is displayed. Click next to AP Wired Port Profile. The AP wired port profile name is displayed. Click next to the specified AP wired port profile to view the profiles that are referenced by the AP wired port profile.
  2. Click any profile referenced by the AP wired port profile. The configuration page of the referenced profile is displayed on the right. You can select another profile from the drop-down list and set the profile parameters. For descriptions of the profile parameters, see its configuration page.
  3. Click Apply. In the Info dialog box that is displayed, click OK.