Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document.
Note: Even the most advanced machine translation cannot match the quality of professional translators.
Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
DOT1X
DOT1X/4/ADD_ACL_FAILED
Procedure
- Run the display acl resource command to check whether ACL resources are sufficient.
- If not, release ACL resources and then run the display acl resource command to check whether ACL resources are successfully released.
- If so, ACLs fail to be delivered to the physical chip. Go to step 2.
- Collect log information and configuration information, and then contact technical support personnel.You can collect diagnostic information using the display diagnostic-information command.
DOT1X/5/QUIETTABLE_FULL
Message
DOT1X/5/QUIETTABLE_FULL:The user cannot be authenticated temporarily,because the number of entries in the quiet table exceeds the upper limit.(MAC Address=[STRING])
Procedure
- Check whether the device is attacked by packets. If so, process these attack packets first.
- The user can be authenticated after the quiet table is aged.
- Collect log information and configuration information, and then contact technical support personnel.You can collect diagnostic information using the display diagnostic-information command.
DOT1X/6/EAPOL_USER_QUIETTABLE_ADD
DOT1X/6/EAPOL_USER_QUIETTABLE_DEL
Message
DOT1X/6/EAPOL_USER_QUIETTABLE_DEL: The user is deleted from quiet-table.(MAC Address:[STRING])
DOT1X/3/MACAUTH_ACL_FAILED
Message
DOT1X/3/MACAUTH_ACL_FAILED: Failed to configure mac authentication because of insufficient resource.(SlotID=[STRING])
Description
MAC address authentication failed to be configured on a VLANIF interface because the ACL resource on the board was insufficient.
Procedure
- Run the display acl resource command to check whether ACL resources are sufficient.
- If not, release ACL resources and then run the display acl resource command to check whether ACL resources are successfully released.
- If so, ACLs fail to be delivered to the physical chip. Go to step 2.
- Collect log and configuration information, and contact technical support. You can collect diagnostic information using the display diagnostic-information command.
DOT1X/4/CONFIGURATE_DOT1X_FREE_IP_FAILED
Parameters
| Parameter Name | Parameter Meaning |
|---|---|
| [STRING] | The dot1x free-ip %s/%u is not supported
on slot %s. NOTE:
|
Procedure
- Run the display acl resource slot slot-number command to check whether ACL resources are sufficient.
- If not, release ACL resources and run the display acl resource slot slot-number command to check whether ACL resources are successfully released.
- If yes, the ACL fails to be delivered to the physical chip. Go to step 2.
- Collect log information and configuration information, and then contact technical support personnel.You can collect diagnostic information using the display diagnostic-information command.
DOT1X/4/CONFIGURATE_DOT1X_URL_FAILED
Parameters
| Parameter Name | Parameter Meaning |
|---|---|
[STRING] |
The redirect URL for 802.1X user authentication fails to be delivered. Value: The dot1x url is not supported on slot %s. NOTE:
%s identifies the ID of a slot. |
Procedure
- Run the display acl resource slot slot-number command to check whether ACL resources are sufficient.
- If not, release ACL resources and then run the display acl resource slot slot-number command to check whether ACL resources are successfully released.
- If so, ACLs fail to be delivered to the physical chip. Go to step 2.
- Collect log information and configuration information, and then contact technical support personnel.You can collect diagnostic information using the display diagnostic-information command.
DOT1X/4/COMMAND_EXECUTE_FAILED
Possible Causes
- The command failed to be delivered because it conflicted with another command configured on the interface.
- The command failed to be delivered due to resource restrictions.
- The command failed to be delivered because the interface was added to an Eth-Trunk.
Procedure
- Check whether the interface configuration is correct based
on logs.
- If so, go to step 2.
- If not, correct the configuration.
- Collect log information and configuration information, and then contact technical support personnel.You can collect diagnostic information using the display diagnostic-information command.
DOT1X/6/USER_EVENT_DOT1X_PROC
Message
DOT1X/6/USER_EVENT_DOT1X_PROC: dot1x authentication procedure. (DeviceMac=[DeviceMac], UserMac=[UserMac], Identify=[Identify], Result=[Result], Msg=[Msg], MsgType=[MsgType], TIME=[TIME], AUTHID=[AUTHID])