SMLK
SMLK/4/MTLK_STATUS_LOG
SMLK/4/SMLK_CMD_LOG
Message
SMLK/4/SMLK_CMD_LOG:The [config-type] configuration on Smart Link group [smlkgroup-id] may cause traffic interruption.
Parameters
Parameter Name | Parameter Meaning |
---|---|
[smlkgroup-id] | SMLK group ID |
[config-type] | configuration type
|
SMLK/4/SMLK_FLUSH_LOG
SMLK/4/SMLK_FLUSH_LOG
SMLK/4/SMLK_STATUS_LOG
SMLK/6/SMLK_EVENT_LOG
Message
SMLK/6/SMLK_EVENT_LOG:Port [STRING]'s ifpdt memory has been clear from [STRING] group [ULONG] as [STRING] in [STRING].
Parameters
Parameter Name | Parameter Meaning |
---|---|
[STRING] | Indicates the port name. |
[STRING] | Indicates the smart link group name or monitor link group name. |
[ULONG] | Indicates the index of the smart link group or monitor link group. |
[STRING] | Indicates the interface status: master or slave for a smart link, and uplink or downlink for a monitor link. |
[STRING] | Indicates the function information. |
SMLK/6/SMLK_EVENT_LOG
Message
SMLK/6/SMLK_EVENT_LOG:Port [STRING]'s ifpdt memory has been set to [STRING] group [ULONG] as [STRING] in [STRING].
Parameters
Parameter Name | Parameter Meaning |
---|---|
[STRING] | Indicates the interface name. |
[STRING] | Indicates the smart link group name or monitor link group name. |
[ULONG] | Indicates the smart link group index or monitor link group index. |
[STRING] | Indicates the interface status: master or slave for a smart link, and uplink or downlink for a monitor link. |
[STRING] | Indicates the function information. |
SMLK/4/SMLK_ERROR_LOG
Description
During Smart Link configuration, error configurations or operation failures are recorded.
Parameters
Parameter Name | Parameter Meaning |
---|---|
[STRING] | Error configurations or operation failures are recorded. |
Procedure
- Run the display acl resource [ slot slot ] command to view information about ACL resources, including ACL4 and ACL6 resources.
- Run the display current-configuration command to check the current configuration on the switch.
- Check the services that occupy ACL resources based on ACL resource information and the current configuration as follows, and delete unnecessary services to release ACL resources.
- Check whether NAC, IPSG, MQC, and ACL-based simplified traffic policy services that occupy a large amount of ACL resources exist on the switch.
- Check the services that occupy ACL resources based on fields in the ACL resource information. For example, MQC, ACL-based simplified traffic policy, SVF, MPLS, and BFD for VPLS services occupy UDF ACL resources. If a large amount of UDF ACL resources are occupied, check these services first.
- If the fault persists, collect log information and configuration information, and then contact technical support personnel. You can collect diagnostic information using the display diagnostic-information command.
SMLK/6/SMLK_FSM_LOG
Message
SMLK/6/SMLK_FSM_LOG:The Smart link group [ULONG]'s current state is [STRING], triggering event is [STRING].
Parameters
Parameter Name | Parameter Meaning |
---|---|
[ULONG] | Indicates the index of the smart link group. |
[STRING] | IDLE/INIT/MASTER/SLAVE |
[STRING] | Smart Link Enable/Smart Link Disable/Master Link Down/Master Link Up/Slave Link Down/Slave Link Up/Add Master Port/Add Slave Port/Delete Master Port/Delete Slave Port/Undo Lock/Undo Force Lock/Force Manual/Timer Expired/Unkown cause |
[STRING] | Indicates the interface name. |
[STRING] | Indicates the smart link group name. |
[ULONG] | Indicates the index of the smart link group. |
[STRING] | Indicates the interface status: master or slave. |
[STRING] | Indicates the function name. |