No relevant resource is found in the selected language.
Enterprise
Worldwide
Huawei Global - English
Support Documentation
S7700 V200R019C10 Log Reference

This document provides the explanations, causes, and recommended actions of logs on the product.

Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
EFM

EFM

EFM/3/INVALID_ORGSPECIFICINFOTLV

Message

EFM/3/INVALID_ORGSPECIFICINFOTLV:Remote Organization Specific Information TLV was invalid. (InterfaceName=[STRING], ErrCode=[ULONG], TLVLength=[ULONG], RemoteState=[ULONG])

Description

The specific TLV of the manufacturer was invalid.

Parameters

Parameter Name Parameter Meaning

InterfaceName

Indicates the name of an interface.

ErrCode

Indicates the error code.

TLVLength

Indicates the length of the TLV.

RemoteState

Indicates the master/slave status of the peer device.

Possible Causes

EFM OAM resolved the specific TLV of the manufacturer and found it invalid.

Procedure

  1. Confirm the type of the error code.

    • If the error code is 1, it indicates that the organization TLV length is invalid.

    • If the error code is 2, it indicates that the organization TLV value is invalid.

  2. Query the configuration of the remote wireless equipment and consult the part describing EFM in the troubleshooting guide.
  3. Collect log information and configuration information, and then contact technical support personnel.

EFM/2/NONTHRESHOLD

Message

EFM/2/NONTHRESHOLD:Non-threshold-crossing event occurred. (InterfaceName=[STRING], EventLogIndex=[GAUGE], EventLogTimestamp=[TIMETICK], EventLogOui=[OPAQUE], EventLogType=[GAUGE], EventLogLocation=[INTEGER], EventLogRunningTotal=[COUNTER64])

Description

The non-threshold-crossing event occurred on the EOAM 3AH module.

Parameters

Parameter Name Parameter Meaning
InterfaceName Indicates the name of an interface.
EventLogIndex Indicates the index of an event.
EventLogTimestamp Indicates the time when the event occurs.
EventLogOui Indicates the unique identifier of a manufacturer.
EventLogType Indicates the log type.
  • 254 indicates the timeout.
  • 256 indicates that the local interface is shut down.
  • 257 indicates the DyingGasp event.
  • 258 indicates the CriticalLink event.
EventLogLocation Indicates the location (1 indicates local end, 2 indicates peer end) of the event.
EventLogRunningTotal Indicates the total of non-threshold-crossing events after the OAM is reset.

Possible Causes

The non-threshold-crossing event was detected.

Procedure

  1. An abnormality occurs on the local end or the peer end.

EFM/6/REMOTE_STATE_CHANGED

Message

EFM/6/REMOTE_STATE_CHANGED:Remote equipment's state changed from [State1] to [State2]. (InterfaceName=[STRING])

Description

The status of the peer device was changed from master to slave or from slave to master.

Parameters

Parameter Name Parameter Meaning
State1 Indicates the original master/slave status of the peer device:

171: Indicates the peer device is in the master state.

186: Indicates the peer device is in the slave state.

0: Indicates that packets from the peer device do not carry information about the master/slave status, or the master/slave status cannot be obtained.
State2 Indicates the current master/slave status of the peer device:

171: indicates the peer device is in the master state.

186: indicates the peer device is in the slave state.

0: indicates that packets from the peer device do not carry information about the master/slave status, or the master/slave status cannot be obtained.
InterfaceName Indicates the interface name.

Possible Causes

1. The status of the peer device was changed from master to slave or from slave to master.

2. The peer device changed from lacking of master/slave information to taking master/slave information.

3. The master/slave status of the peer device could not be obtained owing to link faults.

Procedure

  1. This log message is informational only, and no action is required.

EFM/3/THRESHOLD

Message

EFM/3/THRESHOLD:Threshold-crossing event occurred. (InterfaceName=[STRING], EventLogIndex=[GAUGE], EventLogTimestamp=[TIMETICK], EventLogOui=[OPAQUE], EventLogType=[GAUGE], EventLogLocation=[INTEGER], EventLogWindowHi=[GAUGE], EventLogWindowLo=[GAUGE], EventLogThresholdHi=[GAUGE], EventLogThresholdLo=[GAUGE], EventLogValue=[COUNTER64], EventLogRunningTotal=[COUNTER64], EventLogEventTotal=[GAUGE])

Description

The threshold-crossing event occurred on the EOAM 3AH module.

Parameters

Parameter Name Parameter Meaning
InterfaceName Indicates the name of an interface.
EventLogIndex Indicates the index of an event.
EventLogTimestamp Indicates the time when the event occurs.
EventLogOui Indicates the unique identifier of a manufacturer.
EventLogType Indicates the log type.
EventLogLocation Indicates the location (1 indicates local end, 2 indicates peer end) of the event.
EventLogWindowHi Indicates the higher 4-byte interval.
EventLogWindowLo Indicates the lower 4-byte interval.
EventLogThresholdHi Indicates the higher 4-byte threshold.
EventLogThresholdLo Indicates the lower 4-byte threshold.
EventLogValue Indicates the number of errors within the interval (error frames or error codes).
EventLogRunningTotal Indicates the total number of errors after OAM is reset.
EventLogEventTotal Indicates the total number of threshold-crossing events after OAM is reset.

Possible Causes

The events of error frames, error frame seconds, and error codes were detected. The number of link faults reached the set threshold within the set interval.

Procedure

  1. Check the link and the environment, and analyze the cause of excessive error frames and error codes.

EFM/4/TRIGGERIFNET

Message

EFM/4/TRIGGERIFNET:EFM trigger interface. (InterfaceName=[STRING], Result=[INTEGER])

Description

The service of interface was blocked by the EOAM 3AH module.

Parameters

Parameter Name Parameter Meaning

InterfaceName

Indicates the name of an interface.

Result

Indicates the Status of fault. The detailed information is as follows:

  • Trigger interface up means fault recovery

  • Trigger interface down means fault occurrence

Possible Causes

The interface service block function of 802.3AH was configured, and 802.3AH sense the fault.

Procedure

  1. Check the configurations at both ends of the link.

EFM/5/ISSUSTATUS

Message

EFM/5/ISSUSTATUS: The ISSU working status of EFM is [STRING]. (Time=[ULONG])

Description

The ISSU working status of the EFM module.

Parameters

Parameter Name Parameter Meaning
STRING The ISSU working status of the EFM module.

  • ISSU batch backup of main board in phase 1 started: The first phase for the ISSU batch backup of the main board started.

  • ISSU batch backup of main board in phase 1 over: The first phase for the ISSU batch backup of the main board was over.

  • ISSU batch backup of interface board in phase 1 started: The first phase for the ISSU batch backup of the interface board started.

  • ISSU batch backup of interface board in phase 1 over: The first phase for the ISSU batch backup of the interface board was over.

  • ISSU batch backup recovery of main board in phase 1 started: The first phase for the ISSU configuration recovery of the main board started.

  • ISSU batch backup recovery of main board in phase 1 over: The first phase for the ISSU configuration recovery of the main board was over.

  • ISSU batch backup recovery of interface board in phase 1 started: The first phase for the ISSU configuration recovery of the interface board started.

  • ISSU batch backup recovery of interface board in phase 1 over: The first phase for the ISSU configuration recovery of the interface board was over.
Time Period from the system startup to now, in milliseconds.

Possible Causes

Cause:

The EFM module was performing the ISSU.

Procedure

  1. This log message is informational only, and no action is required.
Translation
简体中文
Download
Updated: 2022-01-25

Document ID: EDOC1100126883

Views: 34724

Downloads: 18

Average rating:
This Document Applies to these Products

Related Version

Related Documents

Digital Signature File

Digital Signature Authentication Mode
Share
Previous Next
Huawei e+ App Huawei e+

Copyright © 2021 Huawei Technologies Co., Ltd. All rights reserved.

You are going to visit :