HUAWEI-MPLS-EXTEND-MIB

1.3.6.1.4.1.2011.5.25.121.1.11

hwStaticLspInIfIndex

OctetString

Accessible-for-notify

Indicates the inbound interface index of a static LSP/CR-LSP.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.1.12

hwStaticLspInIfName

OctetString

Accessible-for-notify

Indicates the name of an inbound interface of a static LSP/CR-LSP.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.2.2.10

hwMplsTunnelDownIfIpAddrType

INTEGER{unknown(0),ipv4(1),ipv6(2),ipv4z(3),ipv6z(4),dns(16)}

accessible-for-notify

The value of this object identifies the IP address type of the error interface on a tunnel.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.1.13

hwStaticLspDownReason

Integer32

Accessible-for-notify

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.2.2.3

hwMplsTunnelDownReason

INTEGER { other(1), staticLspDown(2), staticCrlspDown(3), outIfDown(4), resourcePreempted(5), rsvpMessageTimeout(6), rsvpNeighborLost(7), bypassTunnelDownOrUnbinded(8), cspfComputeFail(9), userShutdown(10), clear(100) }

Accessible-for-notify

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.2.2.4

hwMplsLspProtocol

INTEGER

accessible-for-notify

The value of this object identifies the protocol of the LSP which reaches the threshold or upper limit.

Options:

• 1: indicates the LSP is LDP LSP.

• 2: indicates the LSP is BGP LSP.

• 3: indicates the LSP is BGP IPv6 LSP.

• 4: indicates the LSP is LDP FRR LSP.

• 5: indicates the LSP is RSVP LSP.

• 6: indicates the value is the number of total LSPs.

• 7: indicates the value is the number of total CR-LSPs.

• 8: indicates the value is the number of ingress LDP LSPs.

• 9: indicates the value is the number of transit LDP LSPs.

• 10: indicates the value is the number of egress LDP LSPs.

• 11: indicates the value is the number of ingress BGP LSPs.

• 12: indicates the value is the number of egress BGP LSPs.

• 13: indicates the value is the number of ingress BGP IPv6 LSPs.

• 14: indicates the value is the number of egress BGP IPv6 LSPs.

• 15: indicates the value is the number of ingress RSVP LSPs.

• 16: indicates the value is the number of transit RSVP LSPs.

• 17: indicates the value is the number of egress RSVP LSPs.

• 18: indicates the value is the number of total ingress LSPs.

• 19: indicates the value is the number of total transit LSPs.

• 20: indicates the value is the number of total egress LSPs.

• 21: indicates the value is the number of total ingress CR-LSPs.

• 22: indicates the value is the number of total transit CR-LSPs.

• 23: indicates the value is the number of total egress CR-LSPs.

• 24: indicates the value is the number of total ingress and transit LSPs in public instance.

• 25: indicates the value is the number of total transit and egress LSPs in public instance.

• 26: indicates the value is the number of BGP LSPs in VPN instance.

• 100: indicates the LSP type is unknown.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.2.2.5

hwMplsLspThreshold

Integer32

accessible-for-notify

The value of this object identifies the threshold of the LSPs.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.2.2.6

hwMplsLspTotalCount

Integer32

accessible-for-notify

The value of this object identifies the total permit count of LSPs.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.2.2.7

hwMplsLspCurrentCount

Integer32

accessible-for-notify

The value of this object identifies the current count of the LSPs.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.2.2.8

hwMplsTunnelDownLSRID

OCTET STRING (SIZE (16))

accessible-for-notify

The value of this object identifies the LSR ID of the error node on a tunnel.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.2.2.9

hwMplsTunnelDownIfIpAddr

OCTET STRING (SIZE (0..255))

accessible-for-notify

The value of this object identifies the IP address of the error interface on a tunnel.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.3.1

hwMplsGlobalWorkMode

INTEGER{standard(1),nonstandard(2)}

Read-only

The work mode of DS-TE system. The default mode is nonstandard.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.3.2

hwMplsGlobalBcModel

INTEGER{rdm(1),mam(2),extendMam(3)}

Read-only

Bandwidth Constraint Model currently used by this LSR.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.3.3

hwMplsDynamicLabelTotalCount

INTEGER (0..4294967295)

Read-only

The value of this object identifies the maximum number of dynamic labels.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.3.4

hwMplsDynamicLabelCurrentCount

INTEGER (0..4294967295)

Read-only

The value of this object identifies the current count of the dynamic label.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.3.5

hwMplsDynamicLabelThresholdUpperLimit

INTEGER (0..4294967295)

Read-only

The upper limit threshold value (%) of dynamic label. The default value is 80.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.3.6

hwMplsDynamicLabelThresholdLowerLimit

INTEGER (0..4294967295)

Read-only

The lower limit threshold value (%) of dynamic label. The default value is 70.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.2.2.11

hwMplsResourcetype

INTEGER

Accessible-for-notify

The value of this object identifies the type of MPLS resource, for which a threshold-crossing alarm is generated. The value can be:

• 1: Auto bypass tunnel interfaces

• 2: P2MP Auto bypass tunnel interfaces

• 3: Dynamic BFD sessions for TE

• 4: Dynamic BFD sessions for LDP

• 5: Total number of mLDP trees

• 6: Total number of mLDP branches

• 7: Total number of remote LDP adjacencies

• 8: Total number of out segment of LDP adjacencies

• 9: Total number of auto primary tunnel interfaces

• 10: Total number of the local LDP adjacency threshold-crossing

• 11: Total number of CSPF links

• 12: Total number of CSPF nodes

• 13: Total number of CSPF network LSAs

• 14: Total number of CSPF SRLGs

• 100: Unknown resources

This object is implemented as defined in the corresponding MIB file.

1.3.6.1.4.1.2011.5.25.121.2.2.12

hwMplsResourceCurrentCount

Integer32

Accessible-for-notify

The value of this object identifies the number of used MPLS resources.

This object is implemented as defined in the corresponding MIB file.

1.3.6.1.4.1.2011.5.25.121.2.2.13

hwMplsResourceThreshold

Integer32

Accessible-for-notify

The value of this object identifies the upper alarm threshold for the proportion (percent) of used MPLS resources to MPLS resources supported by a device.

This object is implemented as defined in the corresponding MIB file.

1.3.6.1.4.1.2011.5.25.121.2.2.14

hwMplsResourceTotalCount

Integer32

Accessible-for-notify

The value of this object identifies the maximum number of MPLS resources that a device supports.

This object is implemented as defined in the corresponding MIB file.

1.3.6.1.4.1.2011.5.25.121.2.2.1

hwMplsTunnelIfName

OCTET STRING{(0,255)}

accessible-for-notify

The Tunnel Interface name.

This object is implemented as defined in the corresponding MIB file.

1.3.6.1.4.1.2011.5.25.121.1.1.1.1

hwMplsTunnelIndex

Unsigned32 (0..65535)

Not-accessible

Uniquely identifies a set of tunnel instances between a pair of ingress and egress LSRs.

When the MPLS signaling protocol is rsvp(2), this value equals to the value signaled in the Tunnel ID of the SESSION object. When the MPLS signaling protocol is crldp(3), this value equals to the value signaled in the LSP ID. Reference to MPLS-TE-STD-MIB.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.1.1.1.2

hwMplsTunnelInstance

Unsigned32(0|1..65535|65536..4294967295)

Not-accessible

Uniquely identifies a particular instance of a tunnel between a pair of ingress and egress LSRs. It is used to identify multiple instances of tunnels for backup and parallel tunnels.

When the MPLS signaling protocol is rsvp(2), this value equals to the LSP ID of the Sender Template object. When the signaling protocol is crldp(3), there is no equivalent signaling object. Reference to MPLS-TE-STD-MIB.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.1.1.1.3

hwMplsTunnelIngressLSRId

Unsigned32(0..4294967295)

Not-accessible

Indicates the ingress LSR ID of this tunnel. When the MPLS signaling protocol is rsvp(2), this value equals to the Tunnel Sender Address in the Sender Template object and may equal to the Extended Tunnel ID in the SESSION object. When the MPLS signaling protocol is crldp(3), this value equals to the Ingress LSR Router ID in the LSPID TLV object. Reference to MPLS-TE-STD-MIB.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.1.1.1.4

hwMplsTunnelEgressLSRId

Unsigned32(0..4294967295)

Not-accessible

Indicates the egress LSR ID of this tunnel. Reference to MPLS-TE-STD-MIB.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.1.1.1.5

hwMplsTunnelClassType

INTEGER{bc0(1),bc1(2),invalidValue(3)}

read-only

Indicates the bandwidth type used by this tunnel. Options:

• 1: BC0

• 2: BC1

• 3: invalid value

This object is obsolete. Its value can only be 3.

1.3.6.1.4.1.2011.5.25.121.1.1.1.6

hwMplsTunnelBandwidth

Integer32

read-only

Indicates the bandwidth used by this tunnel.

This object is obsolete. Its value can only be the default invalid value.

1.3.6.1.4.1.2011.5.25.121.1.1.1.7

hwMplsTunnelAdminStatus

INTEGER{up(1),down(2),testing(3)}

Read-only

Indicates the management status of this tunnel. Reference to MPLS-TE-STD-MIB.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.1.1.1.8

hwMplsTunnelOperStatus

INTEGER{up(1),down(2),testing(3),unknown(4),dormant(5),notPresent(6),lowerLayerDown(7)}

Read-only

Indicates the actual operating status of this tunnel, which is but not limited to the status of this tunnel of a certain period. Reference to MPLS-TE-STD-MIB.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.1.1.1.9

hwMplsTunnelSessionAttr

BITS{localProtectionDesired(0),nodeProtectionDesired(1),bandwidthProtectionDesired(2)}

Read-only

Indicates protection types desired by the primary tunnel, such as node protection, link protection or bandwidth protection.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.1.1.1.10

hwMplsTunnelFrrSetupPrio

INTEGER (0..4294967295)

Read-only

Indicates the setup PRI of auto-bypass tunnel. The value ranges from 0 to 7. By default, the setup PRI of auto-bypass tunnel is not set.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.1.1.1.11

hwMplsTunnelFrrHoldingPrio

INTEGER (0..4294967295)

Read-only

Indicates the holding PRI of auto-bypass tunnel. The value ranges from 0 to 7. By default, the setup holding PRI of auto-bypass tunnel is not set.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.1.1.1.12

hwMplsTunnelFrrBandwidth

INTEGER (0..4294967295)

Read-only

Indicates the protecting bandwidth of aut-obypass tunnel. Its value is defined by the configuration on the primary tunnel.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.1.1.1.13

hwMplsTunnelFrrSwitchover

INTEGER (0..4294967295)

Read-only

Indicates FRR switching times.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.1.1.1.14

hwMplsTunnelFrrBypassTableIndex

INTEGER (0..4294967295)

Read-only

Indicates the index of the bypass tunnel table, that is, the LSP ID of the bypass tunnel. The bypass table shows interfaces protected by specified bypass tunnel.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.1.1.1.15

hwMplsTunnelFrrARHopTableIndex

INTEGER (0..4294967295)

Read-only

Indicates the table index of the protection type adopted by each hop of the primary tunnel.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.1.1.1.16

hwMplsTunnelName

OCTET STRING (SIZE (0..255))

Read-only

Indicates the tunnel name. The name can refer to the tunnel on the console port of the LSR. If mplsTunnelIsIf is set to True, the IfName of the interface corresponding to this tunnel should have a value equal to hwMplsTunnelName. Reference to the description of IfName in RFC 2863.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.1.1.1.17

hwMplsTunnelIfIndex

INTEGER (0..4294967295)

Read-only

Indicates the interface index of the tunnel. It uniquely identifies the tunnel name.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.1.1.1.18

hwMplsTunnelPreBandwidth

INTEGER (0..4294967295)

Read-only

The value of this object identifies the original tunnel bandwidth (in kbit/s) after a tunnel is changed.

This object is implemented as defined in the corresponding MIB file.

1.3.6.1.4.1.2011.5.25.121.1.1.1.19

hwMplsTunnelNextBandwidth

INTEGER (0..4294967295)

Read-only

The value of this object identifies the changed tunnel bandwidth (in kbit/s) after a tunnel is changed.

This object is implemented as defined in the corresponding MIB file.

1.3.6.1.4.1.2011.5.25.121.1.1.1.20

hwMplsTunnelCt0Bandwidth

INTEGER (0..4294967295)

Read-only

The bandwidth of Class-Type 0 (CT0) in this tunnel, in Kbit/sec.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.1.1.1.21

hwMplsTunnelCt1Bandwidth

INTEGER (0..4294967295)

Read-only

The bandwidth of Class-Type 1 (CT1) in this tunnel, in Kbit/sec.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.1.1.1.22

hwMplsTunnelCt2Bandwidth

INTEGER (0..4294967295)

Read-only

The bandwidth of Class-Type 2 (CT2) in this tunnel, in Kbit/sec.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.1.1.1.23

hwMplsTunnelCt3Bandwidth

INTEGER (0..4294967295)

Read-only

The bandwidth of Class-Type 3 (CT3) in this tunnel, in Kbit/sec.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.1.1.1.24

hwMplsTunnelCt4Bandwidth

INTEGER (0..4294967295)

Read-only

The bandwidth of Class-Type 4 (CT4) in this tunnel, in Kbit/sec.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.1.1.1.25

hwMplsTunnelCt5Bandwidth

INTEGER (0..4294967295)

Read-only

The bandwidth of Class-Type 5 (CT5) in this tunnel, in Kbit/sec.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.1.1.1.26

hwMplsTunnelCt6Bandwidth

INTEGER (0..4294967295)

Read-only

The bandwidth of Class-Type 6 (CT6) in this tunnel, in Kbit/sec.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.1.1.1.27

hwMplsTunnelCt7Bandwidth

INTEGER (0..4294967295)

Read-only

The bandwidth of Class-Type 7 (CT7) in this tunnel, in Kbit/sec.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.1.1.1.28

hwMplsTunnelLspType

INTEGER { invalid(0), primary(1), primary-modifing(2), hot-standby(3), hot-standby-modifing(4), ordinary(5), ordinary-modifing(6), best-effort(7), best-effort-modifing(8) }

Read-only

1. This object is meaningful only at the ingress of the tunnel.

2. It indicates LSP types:

• 0: indicates that the LSP type is invalid, the possible cause is that the LSP is not created at an ingress.

• 1: indicates the primary LSP.

• 2: indicates the LSP that will replace the primary LSP.

• 3: indicates the hot-standby LSP.

• 4: indicates the LSP that will replace the hot-standby LSP.

• 5: indicates the ordinary LSP.

• 6: indicates the LSP that will replace the ordinary LSP.

• 7: indicates the Best-Effort LSP.

• 8: indicates the LSP that will replace the Best-Effort LSP.

3. Modifying LSPs are created when users modify the make-before-break attribute of the corresponding LSP types. After being created, modifying LSPs replace the corresponding LSPs to transmit traffic.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.1.1.1.29

hwMplsTunnelInterfaceName

OCTET STRING (SIZE (0..255))

Read-only

Indicates the tunnel interface name. The object is only valid at the ingress.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.1.1.1.30

hwMplsTunnelSignalProto

INTEGER { rsvpTE(1), static(2), staticCR(3) }

read-only

Indicates the signal protocol of this tunnel.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.1.1.1.31

hwMplsTunnelType

INTEGER { invalid(1), primaryTunnel(2), bypassTunnel(3) }

read-only

This object is meaningful only at the ingress of the tunnel. It indicates tunnel types:

• 1: indicates that the tunnel type is invalid, the possible cause is that it is not ingress node of this tunnel.

• 2: indicates that this is a primary tunnel.

• 3: indicates that this is a bypass tunnel.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.1.2.1.1

hwTunnelFrrBypassListIndex

INTEGER (0..4294967295)

Not-accessible

Indicates the index of the bypass tunnel table, that is, the LSP ID of the bypass tunnel.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.1.2.1.2

hwTunnelFrrBypassIndex

INTEGER (0..4294967295)

Not-accessible

Indicates the index of the bypass tunnel interface.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.1.2.1.3

hwTunnelFrrBypassProtIfIndex

INTEGER (0..4294967295)

Read-only

Indicates the index of the interface protected by the bypass tunnel.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.1.3.1.1

hwTunnelFrrARHopListIndex

INTEGER (0..4294967295)

Not-accessible

Indicates the table index of each hop along the primary tunnel.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.1.3.1.2

hwTunnelFrrARHopIndex

INTEGER (0..4294967295)

Not-accessible

Indicates the index of each hop along the primary tunnel.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.1.3.1.3

hwTunnelFrrARHopProtDesired

BITS{localProtection(0),nodeProtection(1),bandwidthProtection(2)}

Read-only

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.1.3.1.4

hwTunnelFrrARHopProtActual

BITS{localProtection(0),nodeProtection(1),bandwidthProtection(2),protectionInuse(3)}

Read-only

Indicates the actual FRR protection types of the primary tunnel interface, including:

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.1.4.1.1

hwTunnelFrrRouteDBTunnelIndex

INTEGER (0..4294967295)

Not-accessible

Identifies the index of the primary. Manager obtains new index values for row creation in this table by reading mplsTunnelIndexNext. When the MPLS signaling protocol is rsvp(2), this value equals to the value signaled in the Tunnel ID of the SESSION object. When the MPLS signaling protocol is crldp(3), this value equals to the value signaled in the LSP ID. Reference to MPLS-TE-STD-MIB.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.1.4.1.2

hwTunnelFrrRouteDBTunnelInstance

INTEGER (0..4294967295)

Not-accessible

Uniquely identifies a particular instance of a tunnel between a pair of ingress and egress LSRs. The object identifies multiple instances of tunnels for the purposes of backup and parallel tunnels.

When the MPLS signaling protocol is rsvp(2), this value equals to the LSP Id of the Sender Template object. When the signaling protocol is crldp(3), there is no equivalent signaling object. Reference to MPLS-TE-STD-MIB.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.1.4.1.3

hwTunnelFrrRouteDBTunnelIngressLSRId

INTEGER (0..4294967295)

Not-accessible

Identifies the ingress LSR ID of the primary tunnel. When the MPLS signaling protocol is rsvp(2), LSR ID equals to the Tunnel Sender Address in the Sender Template object or the Extended Tunnel ID in the SESSION object. When the MPLS signaling protocol is crldp(3), LSR ID equals to the Ingress LSR Router ID in the LSPID TLV object.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.1.4.1.4

hwTunnelFrrRouteDBTunnelEngressLSRId

INTEGER (0..4294967295)

Not-accessible

Identifies the egress LSR ID of the primary tunnel. Reference to MPLS-TE-STD-MIB.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.1.4.1.5

hwTunnelFrrRouteDBBypassIfIndex

INTEGER (0..4294967295)

Read-only

Indicates the interface index of the bypass tunnel.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.1.4.1.6

hwTunnelFrrRouteDBInnerLabel

INTEGER (0..4294967295)

Read-only

Indicates the inner label of the primary tunnel and bypass tunnel.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.1.5.1.1

hwStaticLspIndex

OCTET STRING (SIZE(1..24))

Not-accessible

Indicates the index of the static LSP. If the string is 0x00, it means that the index is invalid.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.1.5.1.2

hwStaticLspInSegmentIndex

OCTET STRING (SIZE(1..24))

Not-accessible

Indicates the incoming label index of the static LSP/CR-LSP. If the string is 0x00, it means that the index is invalid. In this case, no corresponding mplsInSegmentEntry exists. Reference to MPLS-LSR-STD-MIB.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.1.5.1.3

hwStaticLspOutSegmentIndex

OCTET STRING (SIZE(1..24))

Not-accessible

Indicates the outgoing index of the static LSP/CR-LSP.

If the entry is used to identify the incoming node or intermediate node of the LSP, this object cannot be set to the string 0x00, because corresponding mplsOutSegmentEntry exists.

If the entry is used to identify the outgoing node of the LSP, this object must be set to the string 0x00. Because no corresponding mplsOutSegmentEntry exists. Reference to MPLS-LSR-STD-MIB.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.1.5.1.4

hwStaticLspOwner

INTEGER{static(1),crstatic(2),other(3)}

Read-only

Denotes the entity that creates and manages the static LSP. This column is automatically filled when the agent is creating rows. The value can be:

Reference to MPLS-LSR-STD-MIB.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.1.5.1.5

hwStaticLspName

OCTET STRING (SIZE (0..255))

Read-only

Indicates the name of the static LSP or CR-LSP. The name is appointed when the static LSP or CR-LSP is created.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.1.5.1.6

hwStaticLspStatus

INTEGER{up(1),down(2),testing(3)}

Read-only

Indicates the actual operating status of the static LSP/CR-LSP. When the static LSP/CR-LSP is in Up state, the value is 1; in Down state, the value is 2; in Testing state, the value is reserved.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.1.5.1.7

hwStaticLspClassType

INTEGER {ct0(1),ct1(2),ct2(3),ct3(4),ct4(5),ct5(6),ct6(7),ct7(8)}

Read-only

The Class-Type of this static LSP.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.1.5.1.8

hwStaticLspBandwidth

INTEGER (0..4294967295)

Read-only

The bandwidth of this static LSP, in Kbit/sec.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.1.7.1.1

hwMplsIfMaxResvBandwidth

INTEGER (0..4294967295)

Read-only

The maximum reservable bandwidth on this interface, in Kbit/sec.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.1.7.1.2

hwMplsIfBc0Bandwidth

INTEGER (0..4294967295)

Read-only

The bandwidth of Class-Type 0 (CT0) in this tunnel, in Kbit/sec.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.1.7.1.3

hwMplsIfBc1Bandwidth

INTEGER (0..4294967295)

Read-only

The bandwidth of Class-Type 1 (CT1) in this tunnel, in Kbit/sec.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.1.7.1.4

hwMplsIfBc2Bandwidth

INTEGER (0..4294967295)

Read-only

The bandwidth of Class-Type 2 (CT2) in this tunnel, in Kbit/sec.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.1.7.1.5

hwMplsIfBc3Bandwidth

INTEGER (0..4294967295)

Read-only

The bandwidth of Class-Type 3 (CT3) in this tunnel, in Kbit/sec.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.1.7.1.6

hwMplsIfBc4Bandwidth

INTEGER (0..4294967295)

Read-only

The bandwidth of Class-Type 4(CT4) in this tunnel, in Kbit/sec.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.1.7.1.7

hwMplsIfBc5Bandwidth

INTEGER (0..4294967295)

Read-only

The bandwidth of Class-Type 5(CT5) in this tunnel, in Kbit/sec.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.1.7.1.8

hwMplsIfBc6Bandwidth

INTEGER (0..4294967295)

Read-only

The bandwidth of Class-Type 6(CT6) in this tunnel, in Kbit/sec.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.1.7.1.9

hwMplsIfBc7Bandwidth

INTEGER (0..4294967295)

Read-only

The bandwidth of Class-Type 7(CT7) in this tunnel, in Kbit/sec.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.1.8.1.1

hwStaticLspTnlName

OCTET STRING (SIZE (0..255))

Not-accessible

Indicates the name of the Static Lsp.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.1.8.1.2

hwStaticLspTnlToken

INTEGER (0..4294967295)

Read-only

Indicates the token of the Static Lsp.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.1.9.1.1

hwMplsTnlID

INTEGER (0..4294967295)

Not-accessible

The value of this object identifies the TE tunnel ID.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.1.9.1.2

hwMplsTeVpnMaxBandwidth

INTEGER (0..4294967295)

Read-only

The value of this object identifies the bandwidth the TE tunnel can provide for VPN QoS, in kbit/s.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.1.9.1.3

hwMplsTeVpnAllocatedBandwidth

INTEGER (0..4294967295)

Read-only

The value of this object identifies the bandwidth used by VPN QoS, in kbit/s.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.4.1.1.1

hwMplsLspStatisticsLspType

INTEGER {ipv4full (0),ipv6full (1),ipv4mask (2),ipv6mask (3),dpi (4),tcp (5),ipv4comp (6),ipv6comp (7),ipv4dyn (8),ipv6dyn (9)}

Not-accessible

This object indicates the LSP type.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.4.1.1.2

hwMplsLspStatisticsIngressLspCount

INTEGER (0..4294967295)

Read-only

This object indicates the number of ingress LSPs of a specified type.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.4.1.1.3

hwMplsLspStatisticsTransitLspCount

INTEGER (0..4294967295)

Read-only

This object indicates the number of transit LSPs of a specified type.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.4.1.1.4

hwMplsLspStatisticsEgressLspCount

INTEGER (0..4294967295)

Read-only

This object indicates the number of egress LSPs of a specified type.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.4.1.1.5

hwMplsLspStatisticsTotalLspCount

INTEGER (0..4294967295)

Read-only

This object indicates the total number of the ingress LSPs, transit LSPs, and egress LSP of specified types.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.2.1.1

hwMplsStaticLspUp

Trap information is output when the status of static LSP changes to Up.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.2.1.2

hwMplsStaticLspDown

Trap information is output when the status of static LSP changes to Down.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.2.1.3

hwMplsStaticCRLspUp

Trap information is output when the status of static CR-LSP changes to Up.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.2.1.4

hwMplsStaticCRLspDown

Trap information is output when the status of static CR-LSP changes to Down.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.2.1.5

hwMplsTeFrrProtAval

For TE FRR notification. Trap information is output when the primary tunnel is bound to bypass tunnel.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.2.1.6

hwMplsTeFrrProtNotAval

hwTunnelFrrRouteDBBypassIfIndex

For TE FRR notification. Trap information is output when the primary tunnel is unbound to bypass tunnel.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.2.1.7

hwMplsTeFrrSwitch

For TE FRR notification. Trap information is output when the primary tunnel switches to the bypass tunnel.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.2.1.8

hwMplsTeFrrResume

For TE FRR notification. Trap information is output when the bypass tunnel is switched back from the primary tunnel.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.2.1.9

hwMplsTunnelHSBSwitch

For Hot Standby notification. The data is switched from the primary CR-LSP to the backup CR-LSP.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.2.1.10

hwMplsTunnelHSBResume

For Hot Standby notification. The data is switched from the backup CR-LSP to the primary CR-LSP.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.2.1.11

hwMplsTunnelOBSwitch

For Ordinary Standby notification. The primary CR-LSP is down and the backup CR-LSP is up.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.2.1.12

hwMplsTunnelOBResume

For Ordinary Standby notification. The data is switched from the backup CR-LSP to the primary CR-LSP.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.2.1.15

hwMplsTunnelChangeBw

Trap information is output when the bandwidth of the tunnel is changed.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.2.1.46

hwMplsTunnelPrimaryUp

This notification indicates that the status of Tunnel Primary LSP changes to Up.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.2.1.47

hwMplsTunnelPrimaryDown

This notification indicates that the status of Tunnel Primary LSP changes to Down.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.2.1.48

hwMplsTunnelHotstandbyUp

This notification indicates that the status of Tunnel Hot-standby LSP changes to Up.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.2.1.49

hwMplsTunnelHotstandbyDown

This notification indicates that the status of Tunnel Hot-standby LSP changes to Down.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.2.1.50

hwMplsTunnelOrdinaryUp

This notification indicates that the status of Tunnel Ordinary LSP changes to Up.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.2.1.51

hwMplsTunnelOrdinaryDown

This notification indicates that the status of Tunnel Ordinary LSP changes to Down.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.2.1.52

hwMplsTunnelBesteffortUp

This notification indicates that the status of Tunnel Best-effort LSP changes to Up.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.2.1.53

hwMplsTunnelBesteffortDown

This notification indicates that the status of Tunnel Best-effort LSP changes to Down.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.2.1.54

hwMplsTeAutoTunnelDownClear

This notification indicates that the TE Auto tunnel Down alarm was cleared.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.2.1.55

hwMplsTeAutoTunnelPrimaryDownClear

hwMplsTunnelInterfaceName

This notification indicates that the Down alarm about the primary LSP in the TE Auto tunnel was cleared.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.2.1.58

hwMplsExtTunnelDown

This notification indicates that the status of te tunnel changes to Down.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.2.1.59

hwMplsExtTunnelDownClear

This notification indicates that the down alarm of te tunnel was cleared.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.2.1.56

hwMplsTunnelBBSwitch

• hwMplsTunnelAdminStatus

• hwMplsTunnelOperStatus

This notification indicates that the primary CR-LSP is Down and the Best-effort backup CR-LSP is Up.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.2.1.57

hwMplsTunnelBBResume

• hwMplsTunnelAdminStatus

• hwMplsTunnelOperStatus

This notification indicates that data is switched from the Best-effort backup CR-LSP to the primary CR-LSP.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.2.1.63

hwMplsLspThresholdExceed

• hwMplsLspProtocol

• hwMplsLspCurrentCount

• hwMplsLspThreshold

• hwMplsLspTotalCount

The number of LSPs reaches the upper threshold.

This object is implemented as defined in the corresponding MIB file.

1.3.6.1.4.1.2011.5.25.121.2.1.64

hwMplsLspThresholdExceedClear

• hwMplsLspProtocol

The number of LSPs falls below the lower threshold.

This object is implemented as defined in the corresponding MIB file.

1.3.6.1.4.1.2011.5.25.121.2.1.65

hwMplsLspTotalCountExceed

• hwMplsLspProtocol

• hwMplsLspTotalCount

The total number of LSPs reaches the upper limit.

This object is implemented as defined in the corresponding MIB file.

1.3.6.1.4.1.2011.5.25.121.2.1.66

hwMplsLspTotalCountExceedClear

• hwMplsLspProtocol

The total number of LSPs falls below 95% of the upper limit.

This object is implemented as defined in the corresponding MIB file.

1.3.6.1.4.1.2011.5.25.121.2.1.62

hwMplsTunnelDelete

• mplsTunnelAdminStatus

• mplsTunnelOperStatus

• hwMplsTunnelIfName

The MPLS TE tunnel was deleted.

This object is implemented as defined in the corresponding MIB file.

1.3.6.1.4.1.2011.5.25.121.2.1.60

hwMplsOamLocalLock

• hwMplsTunnelInterfaceName

• hwMplsTunnelSignalProto

This object indicates that traffic has been locked in the working tunnel.

This object is implemented as defined in the corresponding MIB file.

1.3.6.1.4.1.2011.5.25.121.2.1.61

hwMplsOamLocalLockRecovery

• hwMplsTunnelInterfaceName

• hwMplsTunnelSignalProto

This object indicates that the request for locking traffic in the working tunnel has been canceled.

This object is implemented as defined in the corresponding MIB file.

1.3.6.1.4.1.2011.5.25.121.2.1.67

hwMplsDynamicLabelThresholdExceed

• hwMplsDynamicLabelTotalCount

• hwMplsDynamicLabelCurrentCount

• hwMplsDynamicLabelThresholdUpperLimit

• hwMplsDynamicLabelThresholdLowerLimit

This object indicates that dynamic label usage reaches the upper Threshold.

This object is implemented as defined in the corresponding MIB file.

1.3.6.1.4.1.2011.5.25.121.2.1.68

hwMplsDynamicLabelThresholdExceedClear

• hwMplsDynamicLabelTotalCount

• hwMplsDynamicLabelCurrentCount

• hwMplsDynamicLabelThresholdUpperLimit

• hwMplsDynamicLabelThresholdLowerLimit

This object indicates that dynamic label usage falls below the lower threshold.

This object is implemented as defined in the corresponding MIB file.

1.3.6.1.4.1.2011.5.25.121.2.1.69

hwMplsDynamicLabelTotalCountExceed

• hwMplsDynamicLabelTotalCount

• hwMplsDynamicLabelCurrentCount

This object indicates that dynamic label usage reaches the upper limit.

This object is implemented as defined in the corresponding MIB file.

1.3.6.1.4.1.2011.5.25.121.2.1.70

hwMplsDynamicLabelTotalCountExceedClear

• hwMplsDynamicLabelTotalCount

• hwMplsDynamicLabelCurrentCount

This object indicates that dynamic label usages falls below 95% of the upper limit.

This object is implemented as defined in the corresponding MIB file.

1.3.6.1.4.1.2011.5.25.121.2.1.71

hwMplsResourceThresholdExceed

• hwMplsResourceType

• hwMplsResourceCurrentCount

• hwMplsResourceThreshold

• hwMplsResourceTotalCount

This object indicates that the proportion of used MPLS resources to supported MPLS resources reaches the upper alarm threshold.

This object is implemented as defined in the corresponding MIB file.

1.3.6.1.4.1.2011.5.25.121.2.1.72

hwMplsResourceThresholdExceedClear

hwMplsResourceType

This object indicates that the proportion of used MPLS resources to supported MPLS resources falls below the lower alarm threshold.

This object is implemented as defined in the corresponding MIB file.

1.3.6.1.4.1.2011.5.25.121.2.1.73

hwMplsResourceTotalCountExceed

• hwMplsResourceType

• hwMplsResourceTotalCount

This object indicates that the number of used MPLS resources reaches the maximum number of MPLS resources.

This object is implemented as defined in the corresponding MIB file.

1.3.6.1.4.1.2011.5.25.121.2.1.74

hwMplsResourceTotalCountExceedClear

hwMplsResourceType

This object indicates that the number of used MPLS resources falls below 95% of the maximum number of all MPLS resources.

This object is implemented as defined in the corresponding MIB file.

1.3.6.1.4.1.2011.5.25.121.2.1.77

hwMplsTunnelCommitLost

None

The configuration of an MPLS TE was not committed.

This object is implemented as defined in the corresponding MIB file.

1.3.6.1.4.1.2011.5.25.121.2.1.78

hwMplsTunnelCommitLostClear

None

The configurations of all MPLS TE tunnels were committed.

This object is implemented as defined in the corresponding MIB file.

1.3.6.1.4.1.2011.5.25.121.2.1.79

hwMplsTunnelHotstandbySwitch

For Hot Standby notification. The data is switched from the primary LSP to the backup LSP.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.2.1.80

hwMplsTunnelHotstandbyResume

For Hot Standby notification. The data is switched from the backup LSP to the primary LSP.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.2.1.83

hwMplsTeLspBfdDown

• hwMplsTunnelInterfaceName
• hwMplsTunnelLspType

This object indicates that an alarm is generated after BFD detects a TE LSP Down event.

This object is implemented as defined in the corresponding MIB file.

1.3.6.1.4.1.2011.5.25.121.2.1.84

hwMplsTeLspBfdDownClear

• hwMplsTunnelInterfaceName
• hwMplsTunnelLspType

This object indicates that a clear alarm is generated after BFD detects a TE LSP Up event.

This object is implemented as defined in the corresponding MIB file.