HUAWEI-PORT-MIB

1.3.6.1.4.1.2011.5.25.157.1.28.1

hwUUHashRiskReason

OctetString {(0,256)}

accessible-for-notify

The specific cause of packet loss or excess packets when some Eth-Trunks on the device are forwarding unknown unicast packets.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.157.1.1.1.1.1

hwEthernetIfIndex

INTEGER

Not-accessible

This object indicates the index of a current in-position interface.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.157.1.1.1.1.13

hwEthernetSpeedSet

INTEGER {

other(1),

speed10(2),

speed100(3),

speed1000(4),

speed10000(5),

speed40000(6),

speed20000(7),

speed100000(10),

speed25000(13)

}

Read-write

The value of this object identifies the transmission rate of an Ethernet interface.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.157.1.1.1.1.14

hwEthernetDuplex

INTEGER{

full(1),

half(2)

}

Read-write

This object indicates the duplex mode of an Ethernet interface.

Ethernet electrical interfaces can work in either half-duplex or full-duplex mode. Ethernet optical interfaces can only work in full-duplex mode.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.157.1.1.1.1.15

hwEthernetNegotiation

INTEGER{enabled(1),disabled(2)}

Read-write

The value of this object identifies the auto-negotiation mode on an Ethernet electrical interface. By default, the value is enable.

hwEthernetSpeedSet, hwEthernetDuplex, and hwEthernetNegotiation are associated with each other.

• If hwEthernetNegotiation is set to enable, the values of hwEthernetSpeedSet and hwEthernetDuplex are obtained through auto-negotiation.
• hwEthernetSpeedSet and hwEthernetDuplex can be set only when hwEthernetNegotiation is set to disable.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.157.1.1.1.1.37

hwEthernetJumboframeMaxLength

INTEGER32(1536..12288)

Read-write

The value of this object identifies the maximum frame length allowed by an Ethernet interface.

The value varies according to device models. For details, see jumboframe enable.

1.3.6.1.4.1.2011.5.25.157.1.1.1.1.38

hwEthernetComboType

INTEGER

1: auto(1)

2: copper(2)

3: fiber(3)

4: other(4)

Read-write

This object indicates the working mode of the combo interface.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.157.1.1.1.1.39

hwEthernetPortMode

INTEGER

1: copper(1)

2: fiber(2)

3: other(3)

Read-only

This object indicates the working mode of the interface.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.157.1.8.1.1.1

hwPhysicalPortIfIndex

INTEGER

accessible-for-notif

This object indicates the index of a physical interface on the switch.

This object is implemented as defined in the corresponding MIB file.

1.3.6.1.4.1.2011.5.25.157.1.8.1.1.4

hwPhysicalPortName

OCTET STRING

read-only

This object indicates the interface name.

This object is implemented as defined in the corresponding MIB file.

1.3.6.1.4.1.2011.5.25.157.1.8.1.1.20

hwInputRateChangeThresholdPercent

Integer32

read-write

This object indicates the trap threshold for a sudden traffic volume change in the inbound direction.

This object is implemented as defined in the corresponding MIB file.

1.3.6.1.4.1.2011.5.25.157.1.8.1.1.21

hwOutputRateChangeThresholdPercent

Integer32

read-write

This object indicates the trap threshold for a sudden traffic volume change in the outbound direction.

This object is implemented as defined in the corresponding MIB file.

1.3.6.1.4.1.2011.5.25.157.1.8.1.1.22

hwCurrentStatisticalPeriodRate

INTEGER (0..18446744073709551615)

read-only

This object indicates the interface rate in the current traffic statistics collection interval.

This object is implemented as defined in the corresponding MIB file.

1.3.6.1.4.1.2011.5.25.157.1.8.1.1.23

hwLastStatisticalPeriodRate

INTEGER (0..18446744073709551615)

read-only

This object indicates the interface rate in the previous traffic statistics collection interval.

This object is implemented as defined in the corresponding MIB file.

1.3.6.1.4.1.2011.5.25.157.1.8.1.1.41

hwInputDiscardEnable

INTEGER{enabled(1),disabled(2)}

read-write

This object indicates that the function of reporting an alarm if incoming packets are discarded due to a congestion is enabled.

This object is implemented as defined in the corresponding MIB file.

1.3.6.1.4.1.2011.5.25.157.1.8.1.1.42

hwInputDiscardThreshold

Unsigned 32 (100..4294967295)

read-write

This object indicates the alarm threshold for the number of discarded incoming packets due to a congestion.

This object is implemented as defined in the corresponding MIB file.

1.3.6.1.4.1.2011.5.25.157.1.8.1.1.43

hwInputDiscardInterval

Integer32

read-write

This object indicates the interval for reporting an alarm if incoming packets are discarded due to a congestion.

This object is implemented as defined in the corresponding MIB file.

1.3.6.1.4.1.2011.5.25.157.1.8.1.1.44

hwInputDiscardStatistics

INTEGER (0..18446744073709551615)

read-only

This object indicates the statistics collected on discarding incoming packets due to a congestion.

This object is implemented as defined in the corresponding MIB file.

1.3.6.1.4.1.2011.5.25.157.1.8.1.1.45

hwOutputDiscardEnable

INTEGER{enabled(1),disabled(2)}

read-write

This object indicates that the function of reporting an alarm if outgoing packets are discarded due to a congestion is enabled.

This object is implemented as defined in the corresponding MIB file.

1.3.6.1.4.1.2011.5.25.157.1.8.1.1.46

hwOutputDiscardThreshold

Unsigned 32 (100..4294967295)

read-write

This object indicates the alarm threshold for the number of discarded outgoing packets due to a congestion.

This object is implemented as defined in the corresponding MIB file.

1.3.6.1.4.1.2011.5.25.157.1.8.1.1.47

hwOutputDiscardInterval

Integer32

read-write

This object indicates the interval for reporting an alarm if outgoing packets are discarded due to a congestion.

This object is implemented as defined in the corresponding MIB file.

1.3.6.1.4.1.2011.5.25.157.1.8.1.1.48

hwOutputDiscardStatistics

INTEGER (0..18446744073709551615)

read-only

This object indicates the statistics collected on discarded outgoing packets due to a congestion.

This object is implemented as defined in the corresponding MIB file.

1.3.6.1.4.1.2011.5.25.157.1.14.1.1.1

hwPhysicalPortThrIfIndex

Integer32

accessible-for-notify

This object indicates the interface index.

This object is implemented as defined in the corresponding MIB file.

1.3.6.1.4.1.2011.5.25.157.1.14.1.1.2

hwPhysicalPortThrName

OCTET STRING

read-only

This object indicates the interface name.

This object is implemented as defined in the corresponding MIB file.

1.3.6.1.4.1.2011.5.25.157.1.14.1.1.60

hwInputBroadcastChangeThreshold

INTEGER (0..4294967295)

read-only

This object indicates the threshold of the broadcast packet rate change in the inbound direction of interfaces.

This object is implemented as defined in the corresponding MIB file.

1.3.6.1.4.1.2011.5.25.157.1.14.1.1.61

hwCurrentStatisticalInputBroadcast

INTEGER (0..18446744073709551615)

read-only

This object indicates the broadcast packet rate in the inbound direction of interfaces in the current traffic statistics collection interval.

This object is implemented as defined in the corresponding MIB file.

1.3.6.1.4.1.2011.5.25.157.1.14.1.1.63

hwPhysicalPortInputStatistics

INTEGER (0..18446744073709551615)

read-only

This object indicates the number of received packets on an interface.

This object is implemented as defined in the corresponding MIB file.

1.3.6.1.4.1.2011.5.25.157.1.14.1.1.64

hwPhysicalPortCrcErrorRatioInterval

INTEGER (0..4294967295)

read-write

This object indicates the interval for calculating the percentage of CRC packets against all the received packets on an interface. The value is an integer that ranges from 10 to 65535, in seconds.

This object is implemented as defined in the corresponding MIB file.

1.3.6.1.4.1.2011.5.25.157.1.14.1.1.62

hwBaseStatisticalInputBroadcast

INTEGER (0..18446744073709551615)

read-only

This object indicates the base broadcast packet rate in the inbound direction of interfaces.

This object is implemented as defined in the corresponding MIB file.

1.3.6.1.4.1.2011.5.25.157.1.16.1.1.1

hwPortProtectGroupId

Integer32

not-accessible

This object indicates the port protection group index on the device.

0~127

1.3.6.1.4.1.2011.5.25.157.1.16.1.1.2

hwPortProtectMasterIfIndex

Integer32

read-create

This object indicates the master port index added to the port group.

1

1.3.6.1.4.1.2011.5.25.157.1.16.1.1.3

hwPortProtectMasterStatus

INTEGER { work(1), protect(2), down(3) }

read-only

This object indicates the master port status.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.157.1.16.1.1.4

hwPortProtectSlaveIfIndex

Integer32

read-create

This object indicates the slave port index added to the port group.

1

1.3.6.1.4.1.2011.5.25.157.1.16.1.1.5

hwPortProtectSlaveStatus

INTEGER { work(1), rotect(2), down(3) }

read-only

This object indicates the slave port status.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.157.1.16.1.1.6

hwPortProtectRowStatus

RowStatus { active(1), notInService(2), notReady(3), createAndGo(4), createAndWait(5), destroy(6) }

read-create

This object indicates the row status of the port protection group.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.157.1.19.1.1.1

hwPortDescriptionIfIndex

Integer32

not-accessible

This object indicates the interface index.

This object is implemented as defined in the corresponding MIB file.

1.3.6.1.4.1.2011.5.25.157.1.19.1.1.2

hwPortDescriptionIfPortDescription

INTEGER { router(1), switch(2), phone(3), desktop (4), null(5) }

read-write

This object indicates type description of the object connected to the port.

This object is implemented as defined in the corresponding MIB file.

1.3.6.1.4.1.2011.5.25.157.1.18.2.1.1

hwIpIfStatsIPVersion

INTEGER

not-accessible

This object is implemented as defined in the corresponding MIB file.

1.3.6.1.4.1.2011.5.25.157.1.18.2.1.2

hwIpIfStatsIfIndex

Integer32

not-accessible

This object indicates the interface index.

This object is implemented as defined in the corresponding MIB file.

1.3.6.1.4.1.2011.5.25.157.1.18.2.1.3

hwIpIfInOctetRate

INTEGER (0..18446744073709551615)

read-only

This object indicates the rate of bytes in IP packets in the inbound direction of the interface.

This object is implemented as defined in the corresponding MIB file.

1.3.6.1.4.1.2011.5.25.157.1.18.2.1.4

hwIpIfInPktRate

INTEGER (0..18446744073709551615)

read-only

This object indicates the rate of IP packets in the inbound direction of the interface.

This object is implemented as defined in the corresponding MIB file.

1.3.6.1.4.1.2011.5.25.157.1.18.2.1.5

hwIpIfOutOctetRate

INTEGER (0..18446744073709551615)

read-only

This object indicates the rate of bytes in IP packets in the outbound direction of the interface.

This object is implemented as defined in the corresponding MIB file.

1.3.6.1.4.1.2011.5.25.157.1.18.2.1.6

hwIpIfOutPktRate

INTEGER (0..18446744073709551615)

read-only

This object indicates the rate of IP packets in the outbound direction of the interface.

This object is implemented as defined in the corresponding MIB file.

1.3.6.1.4.1.2011.5.25.157.1.18.2.1.7

hwIpIfInOctets

INTEGER (0..18446744073709551615)

read-only

This object indicates the number of bytes in IP packets in the inbound direction of the interface.

This object is implemented as defined in the corresponding MIB file.

1.3.6.1.4.1.2011.5.25.157.1.18.2.1.8

hwIpIfInPkts

INTEGER (0..18446744073709551615)

read-only

This object indicates the number of IP packets in the inbound direction of the interface.

This object is implemented as defined in the corresponding MIB file.

1.3.6.1.4.1.2011.5.25.157.1.18.2.1.9

hwIpIfOutOctets

INTEGER (0..18446744073709551615)

read-only

This object indicates the number of bytes in IP packets in the outbound direction of the interface.

This object is implemented as defined in the corresponding MIB file.

1.3.6.1.4.1.2011.5.25.157.1.18.2.1.10

hwIpIfOutPkts

INTEGER (0..18446744073709551615)

read-only

This object indicates the number of IP packets in the outbound direction of the interface.

This object is implemented as defined in the corresponding MIB file.

1.3.6.1.4.1.2011.5.25.157.2.247

hwBoardNotSupportAssignTrunk

entPhysicalName

The card on the device does not support Eth-Trunk specification extensions.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.157.2.300

hwInputDiscardNotice

• hwInputDiscardStatistics
• hwInputDiscardThreshold
• hwInputDiscardInterval
• hwPhysicalPortName

This object indicates that the number of discarded incoming packets on the interface exceeds the threshold.

This object is implemented as defined in the corresponding MIB file.

1.3.6.1.4.1.2011.5.25.157.2.301

hwOutputDiscardNotice

• hwOutputDiscardStatistics
• hwOutputDiscardThreshold
• hwOutputDiscardInterval
• hwPhysicalPortName

This object indicates that the number of discarded outgoing packets on the interface exceeds the threshold.

This object is implemented as defined in the corresponding MIB file.

1.3.6.1.4.1.2011.5.25.157.2.219

hwInputRateChangeOverThresholdNotice

• hwPhysicalPortName

• hwInputRateChangeThresholdPercent

• hwCurrentStatisticalPeriodRate

• hwLastStatisticalPeriodRate

This object indicates that the switch generates a trap when the sudden traffic volume change percentage in the inbound direction of interfaces exceeds the trap threshold.

This object is implemented as defined in the corresponding MIB file.

1.3.6.1.4.1.2011.5.25.157.2.220

hwOutputRateChangeOverThresholdNotice

• hwPhysicalPortName

• hwOutputRateChangeThresholdPercent

• hwCurrentStatisticalPeriodRate

• hwLastStatisticalPeriodRate

This object indicates that the switch generates a trap when the sudden traffic volume change percentage in the outbound direction of interfaces exceeds the trap threshold.

This object is implemented as defined in the corresponding MIB file.

1.3.6.1.4.1.2011.5.25.157.2.211

hwNotSameBoardInTrunk

hwPhysicalPortIfIndex

hwPhysicalPortName

During configuration restoration, interfaces on different types of cards join the same Eth-Trunk.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.157.2.157.21

hwPhysicalPortCrcRatioExceed

This object indicates that the percentage of received CRC packets on an interface against all the received packets exceeds the alarm threshold.

This object is implemented as defined in the corresponding MIB file.

1.3.6.1.4.1.2011.5.25.157.2.157.22

hwPhysicalPortCrcRatioResume

This object indicates that the percentage of received CRC packets on an interface against all the received packets is lower than the alarm threshold.

This object is implemented as defined in the corresponding MIB file.

1.3.6.1.4.1.2011.5.25.157.2.157.20

hwPhysicalPortInBroadcastRapidChange

hwPhysicalPortThrIfIndex

hwPhysicalPortThrName

hwInputBroadcastChangeThreshold

hwCurrentStatisticalInputBroadcast

hwBaseStatisticalInputBroadcast

This object indicates that the volume of broadcast traffic in the inbound direction of interfaces changes suddenly.

This object is implemented as defined in the corresponding MIB file.

1.3.6.1.4.1.2011.5.25.157.2.239

hwSubIfNumExceededSpecAlarm

hwSubIfSpecNum

This object indicates that the number of sub-interfaces on the switch exceeds the maximum value.

This object is implemented as defined in the corresponding MIB file.

1.3.6.1.4.1.2011.5.25.157.2.240

hwSubIfNumExceededSpecAlarmResume

hwSubIfSpecNum

This object indicates that the number of sub-interfaces on the switch is less than or equal to the maximum value.

This object is implemented as defined in the corresponding MIB file.

1.3.6.1.4.1.2011.5.25.157.2.305

hwTunnelIfNumExceededSpecAlarm

• hwTunnelIfSpecNum
• hwTunnelIfCurrentNum

The alarm is generated if the number of tunnel interfaces exceeds the upper limit.

This object is implemented as defined in the corresponding MIB file.

1.3.6.1.4.1.2011.5.25.157.2.280

hwVxlanTrunkHashNotSupport

• hwPhysicalPortThrIfIndex
• hwPhysicalPortThrName

This object indicates that the IP address-based load balancing mode configured on an Eth-Trunk does not take effect for VXLAN packets when the Eth-Trunk functions as the outbound interface of VXLAN packets.

This object is implemented as defined in the corresponding MIB file.

1.3.6.1.4.1.2011.5.25.157.2.293

hwTrunkUUHashRisk

hwUUHashRiskReason

This object indicates that packet loss or excess packets may occur when some Eth-Trunks on the device are forwarding unknown unicast packets.

This object is implemented as defined in the corresponding MIB file.