HUAWEI-MPLSLDP-MIB

1.3.6.1.4.1.2011.5.25.143.1.1

hwMplsLdpProcessName

OCTET STRING

Read-only

This object indicates the process name of LDP running on the switch.

By default, the value is LDP.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.143.1.2

hwMplsLdpLspFec

OCTET STRING (SIZE (0..255))

Accessible-for-notify

This object indicates the destination address of an LSP.

The value is either a destination IP address or a prefix of an IP address.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.143.1.3

hwMplsLdpLspInLabel

INTEGER (0..4294967295)

Accessible-for-notify

This object indicates that labels are pushed into all the packets for direct MPLS forwarding.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.143.1.4

hwMplsLdpLspOutLabel

INTEGER (0..4294967295)

Accessible-for-notify

This object indicates that all the packets swap labels for MPLS forwarding.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.143.1.5

hwMplsLdpLspOutIfIndex

INTEGER

Accessible-for-notify

The value of this object identifies the index of the outgoing interface of the LSP.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.143.1.6

hwMplsLdpLspDownReason

INTEGER{routeDelete(1),lspmNotify(2),canNotRecoveryFromGr(3),recvReleaseMsg(4),recvWithdrawMsg(5),upStreamLost(6),downStreamLost(7),otherReason(8)}

Accessible-for-notify

This object indicates the cause why the LSP becomes Down.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.143.1.9

hwLdpCapabilityConfig

INTEGER{enabled(1),disabled(2)}

Read-write

This object indicates the global configuration or deletion of the LDP capability. Before enabling LDP capability, ensure that the MPLS capability is enabled globally.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.143.1.10

hwLdpLsrId

OCTET STRING (SIZE (4))

Read-write

This object indicates the way to change the LDP LSR ID. The default LDP LSR ID has the same value as the MPLS LSR ID. It is recommended not to change the LDP LSR ID unless necessary.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.143.1.11

hwLdpPropagateIpPrefix

OctetString

Read-write

This object indicates the configuration or deletion of the transit policy for the LDP. The object has a valid length ranging from 1 to 169 characters. The length 0 bytes shows that the transit policy is deleted.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.143.1.12

hwLdpGlobalRemotePwe3

INTEGER{enabled(1),disabled(2)}

Read-write

This object indicates the configuration or deletion of the policy for the LDP remote session. When the object is enabled, do not send mapping message to the remote peer. By default, the policy is disabled, which means that there is no limitation to send mapping message to the remote peer.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.143.1.13

hwLdpMtuSignaling

INTEGER{enabled(1),disabled(2)}

Read-write

This object indicates the configuration or deletion of the MTU signaling function. By default, the MTU signaling function is enabled, and the MTU TLV type in the LDP message is 0x900.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.143.1.14

hwLdpMtuApplyTlv

INTEGER{enabled(1),disabled(2)}

Read-write

This object conflicts with the object hwLdpMtuSignaling. If the object is enabled, it indicates that the MTU TLV type in the LDP message is 0x601 according to the RFC 3988.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.143.1.15

hwLdpGrCapabilityConfig

INTEGER{enabled(1),disabled(2)}

Read-write

This object indicates the configuration or deletion of the LDP GR capability.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.143.1.16

hwLdpGrNeighborLivenessTimer

Integer32

Read-write

This object indicates the way to change the value of GR neighbor liveness timer. By default, the value of the timer is 600 seconds.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.143.1.17

hwLdpGrReconnectTimer

Integer32

Read-write

This object indicates the way to change the value of GR reconnect timer. By default, the value of the timer is 300 seconds.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.143.1.18

hwLdpGrRecoveryTimer

Integer32

Read-write

This object indicates the way to change the value of GR recovery timer. By default, the value of the timer is 300 seconds.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.143.1.30

hwLdpLongestMatch

INTEGER{enabled(1),disabled(2)}

Read-write

This object indicates that the LDP is enabled with the function of searching for routes according to the longest match rule to establish LSPs. By default, the longest match is disabled.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.143.1.37

hwLdpRemotePeerAutoDodRequest

INTEGER{enabled(1),disabled(2)}

Read-write

The value of this object identifies whether the device is globally enabled with the capability of automatically sending Label Mapping messages to remote peers in DoD mode.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.143.1.19

hwMplsLspTrigger

INTEGER{all(1),none(2),host(3),ipprefix(4)}

Read-write

This object indicates the way to configure the LDP policy for the ingress LSP and egress LSP. The default value is host.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.143.1.20

hwMplsLspTriggerIpPrefix

OctetString

Read-write

This object indicates the IP prefix when configuring the LDP policy for the ingress LSP and egress LSP.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.143.1.23

hwLdpReset

INTEGER{reset(1),resetall(2),ready(3)}

Read-write

This object indicates the reset of the LDP protocol.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.143.1.24

hwLdpOutBoundSplitHorizonAll

INTEGER{enabled(1),disabled(2)}

Read-write

This object indicates the way to set the flag of global split horizon. The default value is disabled.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.143.1.25

hwLdpDeleteGtsmAll

INTEGER{delete(1),ready(2)}

Read-write

This object indicates the deletion of the GTSM configurations for all LDP peers.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.143.1.26

hwMplsFrrLspTrigger

INTEGER{all(1),none(2),host(3),ip-prefix(4)}

Read-write

This object indicates the way to configure the LDP policy of global instance for LDP Auto FRR. The default value is host.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.143.1.27

hwMplsFrrLspTriggerIpPrefix

OctetString

Read-write

This object indicates the IP prefix when configuring LDP Auto FRR for the public network instance.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.143.1.21

hwMplsLspTriggerBgpRoute

INTEGER{enabled(1),disabled(2)}

Read-write

This object indicates the policy of triggering the BGP labeled route to create the LDP LSP. The default value is disabled.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.143.1.22

hwMplsLspTriggerBgpRouteIpPrefix

OctetString

Read-write

This object indicates the IP prefix when triggering the BGP labeled route to create the LDP LSP.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.143.1.28

hwLdpBackOffTimerInit

Integer32 (5..2147483)

Read-write

This object indicates the initial value of backoff timer. The default value is 15.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.143.1.29

hwLdpBackOffTimerMax

Integer32 (5..2147483)

Read-write

This object indicates the maximum value of backoff timer. The default value is 120.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.143.1.63

hwLdpInBoundPolicyPeerAllRange

INTEGER{ all(1), none(2), ipprefix(3), host(4) }

Read-write

This object indicates the range of routes for a global inbound LDP policy. The default value is all.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.143.1.64

hwLdpInBoundPolicyPeerAllIpPrefix

OCTET STRING

Read-write

This object indicates the IP prefix list name of routes for a global inbound LDP policy. The default value is NULL.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.143.1.73.1

hwLdpLocalOperationalSessionNumber

Integer32

Read-only

This object indicates the number of local LDP sessions working in the Operational state.

This object is implemented as defined in the corresponding MIB file.

1.3.6.1.4.1.2011.5.25.143.1.73.2

hwLdpRemoteOperationalSessionNumber

Integer32

Read-only

This object indicates the number of remote LDP sessions working in the Operational state.

This object is implemented as defined in the corresponding MIB file.

1.3.6.1.4.1.2011.5.25.143.1.73.3

hwLdpLocalAndRemoteOperationalSessionNumber

Integer32

Read-only

This object indicates the number of coexistent local and remote LDP sessions working in the Operational state.

This object is implemented as defined in the corresponding MIB file.

1.3.6.1.4.1.2011.5.25.143.1.73.4

hwLdpTotalOperationalSessionNumber

Integer32

Read-only

This object indicates the total number of LDP sessions working in the Operational state.

This object is implemented as defined in the corresponding MIB file.

1.3.6.1.4.1.2011.5.25.143.1.7.1.1

hwMplsLdpSessionPeerLsrId

OCTET STRING (SIZE (6))

Not-accessible

This object indicates the LSR ID of the peer in a session.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.143.1.7.1.2

hwMplsLdpSessionIfIndex

Integer32

Accessible-for-notify

This object indicates the index of the interface on which the session is established.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.143.1.7.1.3

hwMplsLdpSessionDownReason

INTEGER{sessionUp(0),

helloHoldTimerExp(1),

ssnHoldTimerExp(2),

resetMplsLdp(3),

undoMplsLdp(4),

undoMpls(5),

undoMplsLdpRemotePeer(6),

modifyGRConfig(7),

modifyGRTimer(8),

modifyKeepaliveTimer(9),

modifyMD5Config(10),

ssnRoleSwitch(11),

modifyMTUConfig(12),

modifyTransportAddress(13),

modifyLDPLsrID(14),

recvNotification(15),

transportAddressNotMatch(16),

protocolGR(17),

ifStatusChanged(18),

tcpDown(19),

otherReason(20),

sentNotification(21),

canntBuildSessionRelation(22),

receiveErrorMessageFromPeer(23),

receiveSocketError(24),

sessionDelete(25),

modifyCapabilityAnnouncementConfig(26)

, modifyLocalLsrID(27)

, modifyP2MP(28)

, modifyMp2mp(29)

}

Accessible-for-notify

This object indicates the cause why the session becomes Down.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.143.1.7.1.4

hwMplsLdpSessionAge

INTEGER (0..4294967295)

Read-only

This object indicates the duration since the session is set up.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.143.1.8.1.1

hwMplsLdpSessionPeerId

OCTET STRING (SIZE (6))

Not-accessible

This object indicates the LSR ID of the LDP peer to which the session is connected.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.143.1.8.1.2

hwMplsLdpSessionLsrId

OCTET STRING (SIZE (6))

Read-only

This object indicates the ID of the local LSR.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.143.1.8.1.3

hwMplsLdpSessionTcpConnectionState

OctetString

Read-only

This object indicates the TCP link status of the session.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.143.1.8.1.4

hwMplsLdpSessionState

OctetString

Read-only

This object indicates the current status of the session.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.143.1.8.1.5

hwMplsLdpSessionRole

OctetString

Read-only

This object indicates the session roles.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.143.1.8.1.6

hwMplsLdpSessionFtFlag

OctetString

Read-only

This object indicates whether the FT of the session is enabled.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.143.1.8.1.7

hwMplsLdpSessionMd5Flag

OctetString

Read-only

This object indicates whether the MD5 is enabled for the peer.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.143.1.8.1.8

hwMplsLdpSessionReconnectTimer

INTEGER (0..4294967295)

Read-only

This object indicates the value of the GR reconnection timer after the negotiation.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.143.1.8.1.9

hwMplsLdpSessionRecoveryTimer

INTEGER (0..4294967295)

Read-only

This object indicates the value of the GR recovery timer after the negotiation.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.143.1.8.1.10

hwMplsLdpSessionKeepAliveTimer

INTEGER (0..4294967295)

Read-only

This object indicates the value of the KeepAlive timer after the negotiation.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.143.1.8.1.11

hwMplsLdpSessionKeepAliveMsgReceived

INTEGER (0..4294967295)

Read-only

This object indicates the number of the KeepAlive messages that the session obtains.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.143.1.8.1.12

hwMplsLdpSessionKeepAliveMsgSent

INTEGER (0..4294967295)

Read-only

This object indicates the number of the KeepAlive messages that the session sends.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.143.1.8.1.13

hwMplsLdpSessionLabelAdvMode

OctetString

Read-only

This object indicates the label distribution mode of the session.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.143.1.8.1.14

hwMplsLdpSessionLocalLabelResourceStatus

OctetString

Read-only

This object indicates the status of the local label resources of the session.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.143.1.8.1.15

hwMplsLdpSessionPeerLabelResourceStatus

OctetString

Read-only

This object indicates the status of the label resources of the LDP peer.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.143.1.8.1.16

hwMplsLdpSessionAgeStatus

INTEGER (0..4294967295)

Read-only

This object indicates the existence time of the session.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.143.1.51.1.1

hwLdpRemoteName

OCTET STRING (SIZE (1..64))

Not-accessible

This object indicates the name of the LDP remote peer. The valid length of the name ranges from 1 to 32 characters.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.143.1.51.1.11

hwLdpRemoteIp

OCTET STRING (SIZE (4))

Read-create

This object indicates the creation of the remote peer LSR ID. If being set, the ID cannot be modified. To modify the ID, delete the original ID and create a new one. If the ID is set as 0.0.0.0, it indicates that the ID is deleted.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.143.1.51.1.12

hwLdpRemotePwe3

INTEGER{enabled(1),disabled(2)}

Read-create

This object indicates the configuration or deletion of the policy for the remote LSR ID. When the object is enabled, do not send the mapping message to the remote peer. By default, the object is disabled, which means that there is no limitation on sending the mapping message to remote peer.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.143.1.51.1.13

hwLdpRemoteKeepaliveTimer

Integer32 (30..65535)

Read-create

This object indicates the value of LDP Keepalive timer. By default, the value of the timer is 45 seconds.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.143.1.51.1.14

hwLdpRemoteHelloTimer

Integer32 (3..65535)

Read-create

This object indicates the value of LDP Hello hold timer. By default, the value of the timer is 45 seconds.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.143.1.51.1.15

hwLdpRemoteKeepaliveSendTimer

Integer32 (0..65535)

Read-create

This object indicates the value of LDP Keepalive send timer. By default, the value of the timer is 0, configuration does not take effect.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.143.1.51.1.16

hwLdpRemoteHelloSendTimer

Integer32 (0..65535)

Read-create

This object indicates the value of LDP Hello send timer. By default, the value of the timer is 0, configuration does not take effect.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.143.1.51.1.17

hwLdpRemoteIgpSyncTimer

Integer32 (0..65535)

Read-create

This object indicates the value of IGP-Sync timer. By default, the timer is set to 10 seconds.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.143.1.51.1.18

hwLdpRemoteIpAutoDoDRequest

INTEGER{enabled(1),disabled(2)}

Read-create

This object identifies whether the remote peer is enabled with the capability of automatically sending a DoD request.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.143.1.51.1.19

hwLdpRemoteIpAutoDoDRequestBlock

INTEGER{enabled(1),disabled(2)}

Read-create

This object indicates whether a single remote peer is disabled from the capability of automatically sending a DoD request.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.143.1.51.1.20

hwLdpRemoteLabelAdvertisementMode

INTEGER { dod(1), du(2) }

Read-create

This object indicates the label distribution mode. The value includes:

• 1: indicates that the label distribution mode is dod.

• 2: indicates that the label distribution mode is du.

The label distribution mode is du by default.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.143.1.51.1.51

hwLdpRemoteRowStatus

INTEGER{active(1),notInService(2),notReady(3),createAndGo(4),createAndWait(5),destroy(6)}

Read-create

This object indicates whether one entry of hwLdpRemoteEntityTable is created or destroyed. The value of this object can be CreatAndGo or Destroy. When the value of the object is set as CreatAndGo, and the entry is correctly created, the status of the object is changed into active.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.143.1.52.1.1

hwLdpPeerLsrId

OCTET STRING (SIZE (4))

Not-accessible

This object indicates the LSR ID of the LDP peer.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.143.1.52.1.11

hwLdpPeerMd5Type

INTEGER{cipher(1),plain(2),null(3)}

Read-create

This object indicates the Md5 type.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.143.1.52.1.12

hwLdpPeerMd5Password

OctetString

Read-create

This object indicates the MD5 password of LDP neighbor. To delete the password, set the password length as zero. When read, it always returns an Octet string with the length of zero.

When a user reads MD5 password of LDP neighbor, this node always returns an Octet string with the length of 0.

1.3.6.1.4.1.2011.5.25.143.1.52.1.13

hwLdpPeerGtsmHops

Integer32

Read-create

This object indicates number of GTSM hops. The valid number of GTSM hops ranges from 1 to 255. When the number of GTSM hops is 0, it indicates that the number is not specified.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.143.1.52.1.14

hwLdpPeerSplitHorizon

INTEGER{enabled(1),disabled(2)}

Read-create

This object indicates the way to set the flag of split horizon for the specified LDP peer. The default value is disabled.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.143.1.52.1.15

hwLdpPeerReset

INTEGER{reset(1),ready(2)}

Read-create

This object indicates the reset of the neighbor services.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.143.1.52.1.18

hwLdpPeerKeychainName

OCTET STRING

Read-create

This object indicates the keychain name. To cancel the Keychain authentication, set the Keychain name length as 0.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.143.1.52.1.23

hwLdpPeerInBoundPolicyRange

OCTET STRING

Read-create

This object indicates the IP prefix list name for the inbound policy.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.143.1.52.1.51

hwLdpPeerRowStatus

INTEGER{active(1),notInService(2),notReady(3),createAndGo(4),createAndWait(5),destroy(6)}

Read-create

This object indicates whether one entry of hwLdpPeerTable is created or destroyed. The value of this object can be CreatAndGo or Destroy. When the value of the object is set as CreatAndGo, and the entry is correctly created, the status of the object is changed into active.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.143.1.53.1.1

hwLdpVpnPeerLsrId

OCTET STRING (SIZE (4))

Not-accessible

This object indicates the LSR ID of the LDP peer.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.143.1.53.1.11

hwLdpVpnPeerMd5Type

INTEGER{cipher(1),plain(2),null(3)}

Read-create

This object indicates the Md5 type.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.143.1.53.1.12

hwLdpVpnPeerMd5Password

OctetString

Read-create

This object indicates the MD5 password of VPN LDP neighbor. To delete the password, set the password length as zero. When read, it always returns an Octet string with the length of zero.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.143.1.53.1.13

hwLdpVpnPeerSplitHorizon

INTEGER{enabled(1),disabled(2)}

Read-create

This object indicates the way to set the flag of split horizon for the specified LDP peer. The default value is disabled.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.143.1.53.1.14

hwLdpVpnPeerReset

INTEGER{reset(1),ready(2)}

Read-create

This object indicates the reset of the neighbor services.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.143.1.53.1.17

hwLdpVpnPeerKeychainName

OctetString

Read-create

This object indicates the keychain name. To cancel the Keychain authentication, set the Keychain name length as 0.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.143.1.53.1.51

hwLdpVpnPeerRowStatus

INTEGER{active(1),notInService(2),notReady(3),createAndGo(4),createAndWait(5),destroy(6)}

Read-create

This object indicates whether one entry of hwLdpVpnPeerTable is created or destroyed. The value of this object can be CreatAndGo or Destroy. When the value of the object is set as CreatAndGo, and the entry is correctly created, the status of the object is changed into active.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.143.1.54.1.1

hwLdpInterfaceIndex

INTEGER

Not-accessible

This object indicates the interface index. You can get the correct interface index based on ifIndex of ifTable.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.143.1.54.1.12

hwLdpKeepAliveTimer

Integer32 (30..65535)

Read-create

This object indicates the value of Keepalive timer. By default, the value of the timer is 45 seconds.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.143.1.54.1.13

hwLdpIgpSyncTimer

Integer32 (0..65535)

Read-create

This object indicates the value of IGP-Sync timer. By default, the timer is set to 10 seconds.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.143.1.54.1.14

hwLdpHelloTimer

Integer32 (3..65535)

Read-create

This object indicates the value of Hello hold timer. By default, the value of the timer is 15 seconds.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.143.1.54.1.15

hwLdpTransportAddressIfIndex

Integer32 (0..2147483647)

Read-create

This object indicates the way to specify the interface that the Transport Address is assigned to. Value: 0..2147483647 The default value of the object for the public interface is the interface that the LDP LSR ID is assigned to. If the LDP LSR ID is not assigned to any interface, then the value of the object is 0, and 0 cannot be set. The default value of the object for the public interface is the interface that the LDP LSR ID is assigned to. The default value of the object for the private interface is the private interface itself. Based on mplsL3VpnIfConfRowStatus of mplsL3VpnIfConfTable, you can find which interface belongs to the VPN. The interface must be bound with the same VPN instance.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.143.1.54.1.16

hwLdpKeepAliveSendTimer

Integer32 (0..65535)

Read-create

This object indicates the value of LDP Keepalive send timer. By default, the value of the timer is 0, configuration does not take effect.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.143.1.54.1.17

hwLdpHelloSendTimer

Integer32 (0..65535)

Read-create

This object indicates the value of LDP Hello send timer. By default, the value of the timer is 0, configuration does not take effect.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.143.1.54.1.51

hwLdpInterfaceRowStatus

INTEGER{active(1),notInService(2),notReady(3),createAndGo(4),createAndWait(5),destroy(6)}

Read-create

This object indicates whether one entry of hwLdpInterfaceTable is created or destroyed. The value of this object can be CreatAndGo or Destroy. When the value of the object is set as CreatAndGo, and the entry is correctly created, the status of the object is changed into active.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.143.1.58.1.1

hwLdpPeerGroupName

OCTET STRING

Not-accessible

This object indicates the name of a peer group.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.143.1.58.1.51

hwLdpPeerGroupRowStatus

INTEGER{active(1),notInService(2),notReady(3),createAndGo(4),createAndWait(5),destroy(6)}

Read-create

This object indicates whether one entry of hwLdpPolicyPeerGroupTable is created or destroyed. The value of this object is CreatAndGo or Destroy. When the value of the object is set to CreatAndGo, and the entry is correctly created, the status of the object will change into active.

This object is implemented as defined in the corresponding MIB files.