HUAWEI-RSVPTE-MIB

1.3.6.1.4.1.2011.5.25.148.1.12.1.1

hwRsvpTeNbr

OCTET STRING (SIZE (4))

accessible-for-notify

IP address of an RSVP neighbor.

This object is implemented as defined in the corresponding MIB file.

1.3.6.1.4.1.2011.5.25.148.1.12.1.2

hwRsvpTeIfNbrCurrentCount

Integer32

Accessible-for-notify

The value of this object identifies the number of existing RSVP neighbors.

This object is implemented as defined in the corresponding MIB file.

1.3.6.1.4.1.2011.5.25.148.1.12.1.3

hwRsvpTeIfNbrThreshold

Integer32

Accessible-for-notify

The value of this object identifies the upper alarm threshold for proportion of configured RSVP neighbors to supported RSVP neighbor.

This object is implemented as defined in the corresponding MIB file.

1.3.6.1.4.1.2011.5.25.148.1.12.1.4

hwRsvpTeIfNbrTotalCount

Integer32

Accessible-for-notify

The value of this object identifies the maximum number of RSVP neighbors that a device supports.

This object is implemented as defined in the corresponding MIB file.

1.3.6.1.4.1.2011.5.25.148.1.12.1.5

hwRsvpTeIfName

OctetString

Accessible-for-notify

This object indicates the name of an RSVP interface.

This object is implemented as defined in the corresponding MIB file.

1.3.6.1.4.1.2011.5.25.148.1.1.1.1

hwRsvpTeSessionNumber

INTEGER (0..4294967295)

Not-accessible

The number of this session. This is for SNMP Indexing purposes only and has no relationship to any protocol value.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.148.1.1.1.2

hwRsvpTeSessionType

INTEGER{dnsSession(1),finrstSession(2),fragSession(3),ftpSession(4),ftpDataSession(5),h225Session(6),h245Session(7),h323rtcpSession(8),h323rtpSession(9),h323t120Session(10),httpSession(11),hwccSession(12),icmpSession(13),ilsSession(14),netbiosdataSession(15),netbiosnameSession(16),netbiosSession(17),rasSession(18),rtcpSession(19),rtpSession(20),rtspSession(21),smtpSession(22),synSession(23),tcpSession(24),telnetSession(25),pptpSession(26),udpSession(27),qqSession(28),msnSession(29),userdefineSession(30),sipSession(31),siprtpSession(32),siptrcpSession(33),greSesion(34)}

Read-only

The type of session (IPv4, IPv6, IPv6 with flow information, etc).

Only IPv4 is supported.

1.3.6.1.4.1.2011.5.25.148.1.1.1.3

hwRsvpTeSessionDestAddr

OCTET STRING

Read-only

The destination address used by all senders in this session.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.148.1.1.1.4

hwRsvpTeSessionDestAddrLength

Integer32

Read-only

The CIDR prefix length of the session address, which is 32 for IPv4 host and multicast addresses, and 128 for IPv6 addresses. This object may not be changed when the value of the RowStatus object is 'active'.

The value is always set as 32.

1.3.6.1.4.1.2011.5.25.148.1.1.1.5

hwRsvpTeSessionSenders

INTEGER (0..4294967295)

Read-only

The number of distinct senders currently known to be part of this session.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.148.1.1.1.6

hwRsvpTeSessionReceivers

INTEGER (0..4294967295)

Read-only

The number of reservations being requested of this system for this session.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.148.1.1.1.7

hwRsvpTeSessionRequests

INTEGER (0..4294967295)

Read-only

The number of reservation requests this system is sending upstream for this session.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.148.1.1.1.8

hwRsvpTeSessionTunnelId

Integer32

Read-only

A 16-bit identifier used in the SESSION that remains constant over the life of the tunnel.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.148.1.1.1.9

hwRsvpTeSessionTunnelExtId

OCTET STRING (SIZE (4))

Read-only

An identifier used in the SESSION that remains constant over the life of the tunnel. Normally the identifier is set to all zeros. Ingress nodes that wish to narrow the scope of a SESSION to the ingress-egress pair may place their IPv4 address here as a globally unique identifier.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.148.1.1.1.10

hwRsvpTeSessionLspsNumber

INTEGER (0..4294967295)

Read-only

The number of LSPs that belong to this session.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.148.1.1.1.11

hwRsvpTeSessionStyle

INTEGER

Read-only

An enumerable value to identify the treatment of reservations for different senders within the same session: WF 10001b, FF01010b, SE 10010b.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.148.1.2.1.1

hwRsvpTeSenderNumber

INTEGER (0..4294967295)

Not-accessible

The number of this sender. This is for SNMP Indexing purposes only and has no relationship to any protocol value.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.148.1.2.1.2

hwRsvpTeSenderType

INTEGER{dnsSession(1),finrstSession(2),fragSession(3),ftpSession(4),ftpDataSession(5),h225Session(6),h245Session(7),h323rtcpSession(8),h323rtpSession(9),h323t120Session(10),httpSession(11),hwccSession(12),icmpSession(13),ilsSession(14),netbiosdataSession(15),netbiosnameSession(16),netbiosSession(17),rasSession(18),rtcpSession(19),rtpSession(20),rtspSession(21),smtpSession(22),synSession(23),tcpSession(24),telnetSession(25),pptpSession(26),udpSession(27),qqSession(28),msnSession(29),userdefineSession(30),sipSession(31),siprtpSession(32),siptrcpSession(33),greSesion(34)}

Read-only

The type of session (IPv4, IPv6, IPv6 with flow information, etc).

Only IPv4 is supported.

1.3.6.1.4.1.2011.5.25.148.1.2.1.3

hwRsvpTeSenderDestAddr

OCTET STRING

Read-only

The destination address used by all senders in this session.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.148.1.2.1.4

hwRsvpTeSenderAddr

OCTET STRING

Read-only

The source address used by this sender in this session.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.148.1.2.1.5

hwRsvpTeSenderDestAddrLength

Integer32

Read-only

The length of the destination address in bits. This is the CIDR Prefix Length, which is 32 bits for IPv4 hosts and multicast addresses.

The value is always set as 32.

1.3.6.1.4.1.2011.5.25.148.1.2.1.6

hwRsvpTeSenderAddrLength

Integer32

Read-only

The length of the sender's address in bits. This is the CIDR Prefix Length, which is 32 bits for IPv4 hosts and multicast addresses.

The value is always set as 32.

1.3.6.1.4.1.2011.5.25.148.1.2.1.7

hwRsvpTeSenderHopAddr

OCTET STRING

Read-only

The address used by the previous RSVP hop (which may be the original sender).

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.148.1.2.1.8

hwRsvpTeSenderHopLih

Integer32

Read-only

The Logical Interface Handle used by the previous RSVP hop (which may be the original sender).

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.148.1.2.1.9

hwRsvpTeSenderInterface

integer32

Read-only

The ifIndex value of the interface on which this PATH message was most recently received.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.148.1.2.1.10

hwRsvpTeSenderTSpecRate

Unsigned32

Read-only

The Average Bit Rate of the senders data stream. Within a transmission burst, the arrival rate may be as fast as hwRsvpTeSenderTSpec-PeakRate (if supported by the service model); however, averaged across two or more burst intervals, the rate should not exceed hwRsvpTeSenderTSpecRate. Note that this is a prediction, often based on the general capability of a type of codec or particular encoding; the measured average rate may be significantly lower.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.148.1.2.1.11

hwRsvpTeSenderTSpecPeakRate

Unsigned32

Read-only

The Peak Bit Rate of the sender's data stream. Traffic arrival is not expected to exceed this rate at any time, apart from the effects of jitter in the network. If not specified in the TSpec, this returns zero or noSuchValue.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.148.1.2.1.12

hwRsvpTeSenderTSpecBurst

Integer32 (0..'7FFFFFFF'h)

Read-only

The size of the largest burst expected from the sender at a time.

The value is always set as constant.

1.3.6.1.4.1.2011.5.25.148.1.2.1.13

hwRsvpTeSenderTSpecMinTu

Integer32 (0..'7FFFFFFF'h)

Read-only

The minimum message size for this flow. The policing algorithm will treat smaller messages as though they are this size.

The value is always set as constant.

1.3.6.1.4.1.2011.5.25.148.1.2.1.14

hwRsvpTeSenderTSpecMaxTu

Integer32 (0..'7FFFFFFF'h)

Read-only

The maximum message size for this flow. The admission algorithm will reject TSpecs whose Maximum Transmission Unit, plus the interface headers, exceed the interface MTU.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.148.1.2.1.15

hwRsvpTeSenderInterval

Integer32

Read-only

The interval between refresh messages as advertised by the Previous Hop.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.148.1.2.1.16

hwRsvpTeSenderRsvpHop

INTEGER{true(1),false(2)}

Read-only

If TRUE, the node believes that the previous IP hop is an RSVP hop. If FALSE, the node believes that the previous IP hop may not be an RSVP hop.

The value is always set as True.

1.3.6.1.4.1.2011.5.25.148.1.2.1.18

hwRsvpTeSenderAdspecBreak

INTEGER{true(1),false(2)}

Read-only

The global break bit general characterization parameter from the ADSPEC. If TRUE, at least one non-IS hop was detected in the path. If FALSE, no non-IS hops were detected.

The value is always set as True.

1.3.6.1.4.1.2011.5.25.148.1.2.1.19

hwRsvpTeSenderAdspecHopCount

Integer32

Read-only

The hop count general characterization parameter from the ADSPEC. A return of zero or no Such Value indicates one of the following conditions: the invalid bit was set or the parameter was not present.

The value is always set as constant.

1.3.6.1.4.1.2011.5.25.148.1.2.1.20

hwRsvpTeSenderAdspecPathBw

Unsigned32

Read-only

The path bandwidth estimate general characterization parameter from the ADSPEC. A return of zero or noSuchValue indicates one of the following conditions: the invalid bit was set or the parameter was not present.

The value is always set as constant.

1.3.6.1.4.1.2011.5.25.148.1.2.1.21

hwRsvpTeSenderAdspecMinLatency

Integer32

Read-only

The minimum path latency general characterization parameter from the ADSPEC. A return of zero or noSuchValue indicates one of the following conditions: the invalid bit was set or the parameter was not present.

The value is always set as constant.

1.3.6.1.4.1.2011.5.25.148.1.2.1.22

hwRsvpTeSenderAdspecMtu

Integer32

Read-only

The composed maximum transmission unit, general characterization parameter from the ADSPEC. A return of zero or noSuchValue indicates one of the following conditions: the invalid bit was set or the parameter was not present.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.148.1.2.1.23

hwRsvpTeSenderAdspecGuaranteedSvc

INTEGER{true(1),false(2)}

Read-only

If TRUE, the ADSPEC contains a Guaranteed Service fragment. If FALSE, the ADSPEC does not contain a Guaranteed Service fragment.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.148.1.2.1.24

hwRsvpTeSenderAdspecGuaranteedBreak

INTEGER{true(1),false(2)}

Read-only

If TRUE, the Guaranteed Service fragment has its 'break' bit set, indicating that one or more nodes along the path do not support the guaranteed service. If FALSE, and hwRsvpTeSen-derAdspecGuaranteedSvc is TRUE, the 'break' bit is not set. If hwRsvpTeSenderAdspecGuaranteedSvc is FALSE, this returns FALSE or noSuchValue.

The value is always set as constant.

1.3.6.1.4.1.2011.5.25.148.1.2.1.25

hwRsvpTeSenderAdspecGuaranteedCtot

Integer32

Read-only

If hwRsvpTeSenderAdspecGuaranteedSvc is TRUE, this is the end-to-end composed value for the guaranteed service 'C' parameter. A return of zero or SuchValue indicates one of the following conditions: the invalid bit was set or the parameter was not present. If hwRsvpTeSenderAdspecGuaranteedSvc is FALSE, this returns zero or noSuchValue.

The value is always set as constant.

1.3.6.1.4.1.2011.5.25.148.1.2.1.26

hwRsvpTeSenderAdspecGuaranteedDtot

Integer32

Read-only

If hwRsvpTeSenderAdspecGuaranteedSvc is TRUE, this is the end-to-end composed value for the guaranteed service 'D' parameter. A return of zero or noSuchValue indicates one of the following conditions: the invalid bit was set or the parameter was not present. If hwRsvpTeSenderAdspecGuaranteedSvc is FALSE, this returns zero or noSuchValue.

The value is always set as constant.

1.3.6.1.4.1.2011.5.25.148.1.2.1.27

hwRsvpTeSenderAdspecGuaranteedCsum

Integer32

Read-only

If hwRsvpTeSenderAdspecGuaranteedSvc is TRUE, this is the composed value for the guaranteed service 'C' parameter since the last reshaping point. A return of zero or noSuchValue indicates one of the following conditions: the invalid bit was set or the parameter was not present. If hwRsvpTeSenderAdspecGuaranteedSvc is FALSE, this returns zero or noSuchValue.

The value is always set as constant.

1.3.6.1.4.1.2011.5.25.148.1.2.1.28

hwRsvpTeSenderAdspecGuaranteedDsum

Integer32

Read-only

If hwRsvpTeSenderAdspecGuaranteedSvc is TRUE, this is the composed value for the guaranteed service 'D' parameter since the last reshaping point. A return of zero or noSuchValue indicates one of the following conditions: the invalid bit was set or the parameter was not present. If hwRsvpTeSenderAdspecGuaranteedSvc is FALSE, this returns zero or noSuchValue.

The value is always set as constant.

1.3.6.1.4.1.2011.5.25.148.1.2.1.29

hwRsvpTeSenderAdspecGuaranteedHopCount

Integer32

Read-only

If hwRsvpTeSenderAdspecGuaranteedSvc is TRUE, this is the service-specific override of the hop count general characterization parameter from the ADSPEC. A return of zero or noSuchValue indicates one of the following conditions: the invalid bit was set or the parameter was not present. If hwRsvpTeSenderAdspecGuaranteedSvc is FALSE, this returns zero or noSuchValue.

The value is always set as constant.

1.3.6.1.4.1.2011.5.25.148.1.2.1.30

hwRsvpTeSenderAdspecGuaranteedPathBw

Unsigned32

Read-only

If hwRsvpTeSenderAdspecGuaranteedSvc is TRUE, this is the service-specific override of the path bandwidth estimate general characterization parameter from the ADSPEC. A return of zero or noSuchValue indicates one of the following conditions: the invalid bit was set or the parameter was not present. If hwRsvpTeSenderAdspecGuaranteedSvc is FALSE, this returns zero or noSuchValue.

The value is always set as constant.

1.3.6.1.4.1.2011.5.25.148.1.2.1.31

hwRsvpTeSenderAdspecGuaranteedMinLatency

Integer32

Read-only

If hwRsvpTeSenderAdspecGuaranteedSvc is TRUE, this is the service-specific override of the minimum path latency general characterization parameter from the ADSPEC.

A return of zero or noSuchValue indicates one of the following conditions: the invalid bit was set or the parameter was not present. If hwRsvpTeSenderAdspecGuaranteedSvc is FALSE, this returns zero or noSuchValue.

The value is always set as constant.

1.3.6.1.4.1.2011.5.25.148.1.2.1.32

hwRsvpTeSenderAdspecGuaranteedMtu

Integer32

Read-only

If hwRsvpTeSenderAdspecGuaranteedSvc is TRUE, this is the service-specific override of the com-posed Maximum Transmission Unit general characterization parameter from the ADSPEC. A return of zero or noSuchValue indicates one of the following conditions: the invalid bit was set or the parameter was not present. If hwRsvpTeSenderAdspecGuaranteedSvc is FALSE, this returns zero or noSuchValue.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.148.1.2.1.33

hwRsvpTeSenderAdspecCtrlLoadSvc

INTEGER{true(1),false(2)}

Read-only

If TRUE, the ADSPEC contains a Controlled Load Service fragment. If FALSE, the ADSPEC does not contain a Controlled Load Service fragment.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.148.1.2.1.34

hwRsvpTeSenderAdspecCtrlLoadBreak

INTEGER{true(1),false(2)}

Read-only

If TRUE, the Controlled Load Service fragment has its 'break' bit set, indicating that one or more nodes along the path do not support the controlled load service. If FALSE, and hwRsvpTeSenderAdspecCtrlLoadSvc is TRUE, the 'break' bit is not set. If hwRsvpTeSenderAdspecCtrlLoadSvc is FALSE, this returns FALSE or noSuchValue.

The value is always set as constant.

1.3.6.1.4.1.2011.5.25.148.1.2.1.35

hwRsvpTeSenderAdspecCtrlLoadHopCount

Integer32

Read-only

If hwRsvpTeSenderAdspecCtrlLoadSvc is TRUE, this is the service-specific override of the hop count general characterization parameter from the ADSPEC. A return of zero or noSuchValue indicates one of the following conditions: the invalid bit was set or the parameter was not present. If hwRsvpTeSenderAdspecCtrlLoadSvc is FALSE, this returns zero or noSuchValue.

The value is always set as constant.

1.3.6.1.4.1.2011.5.25.148.1.2.1.36

hwRsvpTeSenderAdspecCtrlLoadPathBw

Unsigned32

Read-only

If hwRsvpTeSenderAdspecCtrlLoadSvc is TRUE, this is the service-specific override of the path bandwidth estimate general characterization parameter from the ADSPEC. A return of zero or noSuchValue indicates one of the following conditions: the invalid bit was set or the parameter was not present. If hwRsvpTeSenderAdspecCtrlLoadSvc is FALSE, this returns zero or noSuchValue.

The value is always set as constant.

1.3.6.1.4.1.2011.5.25.148.1.2.1.37

hwRsvpTeSenderAdspecCtrlLoadMinLatency

Integer32

Read-only

If hwRsvpTeSenderAdspecCtrlLoadSvc is TRUE, this is the service-specific override of the minimum path latency general characterization parameter from the ADSPEC. A return of zero or noSuchValue indicates one of the following conditions: the invalid bit was set or the parameter was not present. If hwRsvpTeSenderAdspecCtrlLoadSvc is FALSE, this returns zero or noSuchValue.

The value is always set as constant.

1.3.6.1.4.1.2011.5.25.148.1.2.1.38

hwRsvpTeSenderAdspecCtrlLoadMtu

Integer32

Read-only

If hwRsvpTeSenderAdspecCtrlLoadSvc is TRUE, this is the service-specific override of the com- posed Maximum Transmission Unit general characterization parameter from the ADSPEC. A return of zero or noSuchValue indicates one of the following conditions: the invalid bit was set or the parameter was not present. If hwRsvpTeSenderAdspecCtrlLoadSvc is FALSE, this returns zero or noSuchValue.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.148.1.2.1.39

hwRsvpTeSenderTtl

Integer32

Read-only

The TTL value in the RSVP header that was last received.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.148.1.2.1.40

hwRsvpTeLspId

Integer32

Read-only

A 16-bit identifier used in the SENDER_TEMPLATE and the FILTER_SPEC that can be changed to allow a sender to share resources with itself.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.148.1.2.1.41

hwRsvpTeSenderMsgIdSndFlag

Integer32

Read-only

Indicates that the message sender requests the peer to send an acknowledgment for the message (1: ACK desired.).

The value is always set as constant.

1.3.6.1.4.1.2011.5.25.148.1.2.1.42

hwRsvpTeSenderMsgIdSndEpoch

INTEGER (0..4294967295)

Read-only

A value that indicates when the Message_Identifier sequence has been reset.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.148.1.2.1.43

hwRsvpTeSenderMsgIdSndNumber

INTEGER (0..4294967295)

Read-only

When combined with the message generator's IP address, the Message_Identifier field uniquely identifies a message. The values placed in this field change incrementally and only decrease when the Epoch changes or when the value wraps. A return of 0 indicates the absence of the MESSAGE_ID object to be sent.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.148.1.2.1.44

hwRsvpTeSenderMsgIdRcvFlag

Integer32

Read-only

The messageId flag of the message latest received. It is used to identify whether ACK is desired or not. And it can be extended. (1: ACK desired.)

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.148.1.2.1.45

hwRsvpTeSenderMsgIdRcvEpoch

INTEGER (0..4294967295)

Read-only

The messageId Epoch of the message latest received from the interface.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.148.1.2.1.46

hwRsvpTeSenderMsgIdRcvNumber

INTEGER (0..4294967295)

Read-only

The message ID number of the message latest received from the interface. A return of 0 indicates the absence of the MESSAGE_ID object received.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.148.1.2.1.47

hwRsvpTeSenderClassType

Integer32

Read-only

Indicates the class-type. A return of zero indicates the absence of the object.

It is always 0.

1.3.6.1.4.1.2011.5.25.148.1.2.1.48

hwRsvpTeSenderLabelRequestCtype

INTEGER

Read-only

The type of label request (without label range, with ATM label range, with frame relay label range, etc).

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.148.1.2.1.49

hwRsvpTeSenderLabelRequestL3pid

Integer32

Read-only

An identifier of the layer 3 protocol using this path. Standard Ethertype values are used.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.148.1.2.1.50

hwRsvpTeSenderLabelRequestAtmMinVpi

Integer32

Read-only

This 12 bit field specifies the lower bound of a block of Virtual Path Identifiers that is supported on the originating switch.

If the VPI is less than 12-bits it MUST be right justified in this field and preceding bits MUST be set to zero.

The value is always set as constant.

1.3.6.1.4.1.2011.5.25.148.1.2.1.51

hwRsvpTeSenderLabelRequestAtmMinVci

Integer32

Read-only

This 16 bit field specifies the lower bound of a block of Virtual Connection Identifiers that is supported on the originating switch.

If the VCI is less than 16-bits it MUST be right justified in this field and preceding bits MUST be set to zero.

The value is always set as constant.

1.3.6.1.4.1.2011.5.25.148.1.2.1.52

hwRsvpTeSenderLabelRequestAtmMaxVpi

Integer32

Read-only

This 12 bit field specifies the upper bound of a block of Virtual Path Identifiers that is supported on the originating switch.

If the VPI is less than 12-bits it MUST be right justified in this field and preceding bits MUST be set to zero.

The value is always set as constant.

1.3.6.1.4.1.2011.5.25.148.1.2.1.53

hwRsvpTeSenderLabelRequestAtmMaxVci

Integer32

Read-only

This 16 bit field specifies the upper bound of a block of Virtual Connection Identifiers that is supported on the originating switch.

If the VCI is less than 16-bits it MUST be right justified in this field and preceding bits MUST be set to zero.

The value is always set as constant.

1.3.6.1.4.1.2011.5.25.148.1.2.1.54

hwRsvpTeSenderLabelRequestFRMinDlci

Integer32

Read-only

This 23-bit field specifies the lower bound of a block of Data Link Connection Identifiers (DLCIs) that is supported on the originating switch.

The DLCI MUST be right justified in this field and unused bits MUST be set to 0.

The value is always set as constant.

1.3.6.1.4.1.2011.5.25.148.1.2.1.55

hwRsvpTeSenderLabelRequestFRMaxDlci

Integer32

Read-only

This 23-bit field specifies the upper bound of a block of Data Link Connection Identifiers (DLCIs) that is supported on the originating switch.

The DLCI MUST be right justified in this field and unused bits MUST be set to 0.

The value is always set as constant.

1.3.6.1.4.1.2011.5.25.148.1.2.1.56

hwRsvpTeSenderSessionAttrType

INTEGER

Read-only

The type of the session_attribute (without resource affinities or with resource affinities).

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.148.1.2.1.57

hwRsvpTeSenderSessionAttrSetupPrio

Integer32

Read-only

The priority of the session with respect to taking resources, in the range of 0 to 7.

The value 0 is the highest priority. The Setup Priority is used in deciding whether this session can preempt another session.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.148.1.2.1.58

hwRsvpTeSenderSessionAttrHoldPrio

Integer32

Read-only

The priority of the session with respect to holding resources, in the range of 0 to 7.

The value 0 is the highest priority. Holding Priority is used in deciding whether this session can be preempted by another session.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.148.1.2.1.59

hwRsvpTeSenderSessionAttrFlag

Integer32

Read-only

A mixed value.

1.3.6.1.4.1.2011.5.25.148.1.2.1.60

hwRsvpTeSenderSessionAttrName

OCTET STRING

Read-only

Session name, a null padded string of characters.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.148.1.2.1.61

hwRsvpTeSenderSessionAttrExcludeAny

INTEGER (0..4294967295)

Read-only

A 32-bit vector representing a set of attribute filters associated with a tunnel any of which renders a link unacceptable.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.148.1.2.1.62

hwRsvpTeSenderSessionAttrIncludeAny

INTEGER (0..4294967295)

Read-only

A 32-bit vector representing a set of attribute filters associated with a tunnel any of which renders a link acceptable (with respect to this test).

A null set (all bits set to zero) automatically passes.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.148.1.2.1.63

hwRsvpTeSenderSessionAttrIncludeAll

INTEGER (0..4294967295)

Read-only

A 32-bit vector representing a set of attribute filters associated with a tunnel all of which must be present for a link to be acceptable (with respect to this test).

A null set (all bits set to zero) automatically passes.

The value is always set as constant.

1.3.6.1.4.1.2011.5.25.148.1.2.1.64

hwRsvpTeSenderFrrSetupPrio

Integer32

Read-only

The priority of the backup path with respect to taking resources, in the range 0 to 7. The value 0 is the highest priority.

Setup Priority is used in deciding whether this session can preempt another session.

See [RSVP-TE] for the usage on priority.

FAST_REROUTE object only supports Auto-Frr.

1.3.6.1.4.1.2011.5.25.148.1.2.1.65

hwRsvpTeSenderFrrHoldPrio

Integer32

Read-only

The priority of the backup path with respect to holding resources, in the range 0 to 7. The value 0 is the highest priority.

Holding Priority is used in deciding whether this session can be preempted by another session.

FAST_REROUTE object only supports Auto-Frr.

1.3.6.1.4.1.2011.5.25.148.1.2.1.66

hwRsvpTeSenderFrrHopLimit

Integer32

Read-only

The maximum number of extra hops the backup path is allowed to take, from current node (a PLR) to an MP, with PLR and MP excluded from the count.

For example, hop-limit of 0 means that only direct links between PLR and MP can be considered.

The value is always set as constant.

1.3.6.1.4.1.2011.5.25.148.1.2.1.67

hwRsvpTeSenderFrrFlag

INTEGER

Read-only

An enumerable value to indicate the protection schema desired.

The value is always set as constant.

1.3.6.1.4.1.2011.5.25.148.1.2.1.68

hwRsvpTeSenderFrrBandwidth

Unsigned32

Read-only

Bandwidth estimate; 32-bit IEEE floating point integer, in bits per second.

FAST_REROUTE object only supports Auto-Frr.

1.3.6.1.4.1.2011.5.25.148.1.2.1.69

hwRsvpTeSenderFrrExcludeAny

INTEGER (0..4294967295)

Read-only

A 32-bit vector representing a set of attribute filters associated with a backup path, any of which renders a link unacceptable.

The value is always set as constant.

1.3.6.1.4.1.2011.5.25.148.1.2.1.70

hwRsvpTeSenderFrrIncludeAny

INTEGER (0..4294967295)

Read-only

A 32-bit vector representing a set of attribute filters associated with a backup path, any of which renders a link acceptable (with respect to this test).

A null set (all bits set to zero) automatically passes.

The value is always set as constant.

1.3.6.1.4.1.2011.5.25.148.1.2.1.71

hwRsvpTeSenderFrrIncludeAll

INTEGER (0..4294967295)

Read-only

A 32-bit vector representing a set of attribute filters associated with a backup path, all of which must be present for a link to be acceptable (with respect to this test).

A null set (all bits set to zero) automatically passes.

The value is always set as constant.

1.3.6.1.4.1.2011.5.25.148.1.2.1.72

hwRsvpTeSenderFrrInuseFlag

INTEGER

Read-only

An enumerable value to indicate the fast-reroute state of this sender (normal, PLR in use, MP in use, PLR in use and MP in use, under protection).

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.148.1.2.1.73

hwRsvpTeSenderDiffServPsc

Integer32

Read-only

This 16 bits field indicates a PHB Scheduling Class to be supported by the LSP.

The value is always set as 0.

1.3.6.1.4.1.2011.5.25.148.1.3.1.1

hwRsvpTeResvNumber

INTEGER (0..4294967295)

Not-accessible

The number of this reservation request. This is for SNMP Indexing purposes only and has no relationship to any protocol value.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.148.1.3.1.2

hwRsvpTeResvType

INTEGER{dnsSession(1),finrstSession(2),fragSession(3),ftpSession(4),ftpDataSession(5),h225Session(6),h245Session(7),h323rtcpSession(8),h323rtpSession(9),h323t120Session(10),httpSession(11),hwccSession(12),icmpSession(13),ilsSession(14),netbiosdataSession(15),netbiosnameSession(16),netbiosSession(17),rasSession(18),rtcpSession(19),rtpSession(20),rtspSession(21),smtpSession(22),synSession(23),tcpSession(24),telnetSession(25),pptpSession(26),udpSession(27),qqSession(28),msnSession(29),userdefineSession(30),sipSession(31),siprtpSession(32),siptrcpSession(33),greSesion(34)}

Read-only

The type of session (IPv4, IPv6, IPv6 with flow information, etc)

Only IPv4 is supported.

1.3.6.1.4.1.2011.5.25.148.1.3.1.3

hwRsvpTeResvDestAddr

OCTET STRING

Read-only

The destination address used by all senders in this session.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.148.1.3.1.4

hwRsvpTeResvSenderAddr

OCTET STRING

Read-only

The source address of the sender selected by this reservation.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.148.1.3.1.5

hwRsvpTeResvDestAddrLength

Integer32

Read-only

The length of the destination address in bits. This is the CIDR Prefix Length, which is 32 bits for IPv4 hosts and multicast addresses.

The value is always set as 32.

1.3.6.1.4.1.2011.5.25.148.1.3.1.6

hwRsvpTeResvSenderAddrLength

Integer32

Read-only

The length of the sender's address in bits. This is the CIDR Prefix Length, which is 32 bits for IPv4 hosts and multicast addresses.

The value is always set as 32.

1.3.6.1.4.1.2011.5.25.148.1.3.1.7

hwRsvpTeResvHopAddr

OCTET STRING

Read-only

The address used by the next RSVP hop (which may be the ultimate receiver)

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.148.1.3.1.8

hwRsvpTeResvHopLih

Integer32

Read-only

The Logical Interface Handle received from the previous RSVP hop (which may be the ultimate receiver).

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.148.1.3.1.9

hwRsvpTeResvInterface

Integer32

Read-only

The ifIndex value of the interface on which this RESV message was most recently received

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.148.1.3.1.10

hwRsvpTeResvService

INTEGER {bestEffort (1),guaranteedDelay (2),controlledLoad (5)}

Read-only

The QoS Service classification requested by the receiver.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.148.1.3.1.11

hwRsvpTeResvTSpecRate

Unsigned32

Read-only

The Average Bit Rate of the sender's data stream. Within a transmission burst, the arrival rate may be as fast as hwRsvpTeResvTSpecPeakRate (if supported by the service model); however, averaged across two or more burst intervals, the rate should not exceed hwRsvpTeResvTSpecRate.

Note that this is a prediction, often based on the general capability of a type of codec or particular encoding; the measured average rate may be significantly lower.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.148.1.3.1.12

hwRsvpTeResvTSpecPeakRate

Unsigned32

Read-only

The Peak Bit Rate of the sender's data stream. Traffic arrival is not expected to exceed this rate at any time, apart from the effects of jitter in the network. If not specified in the TSpec, this returns zero or noSuchValue.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.148.1.3.1.13

hwRsvpTeResvTSpecBurst

Integer32 (0..'7FFFFFFF'h)

Read-only

The size of the largest burst expected from the sender at a time. If this is less than the sender's advertised burst size, the receiver is asking the network to provide flow pacing beyond what would be provided under normal circumstances. Such pacing is at the network's option.

The value is always set as constant.

1.3.6.1.4.1.2011.5.25.148.1.3.1.14

hwRsvpTeResvTSpecMinTu

Integer32 (0..'7FFFFFFF'h)

Read-only

The minimum message size for this flow. The policing algorithm will treat smaller messages as though they are this size.

The value is always set as constant.

1.3.6.1.4.1.2011.5.25.148.1.3.1.15

hwRsvpTeResvTSpecMaxTu

Integer32 (0..'7FFFFFFF'h)

Read-only

The maximum message size for this flow. The admission algorithm will reject TSpecs whose Maximum Transmission Unit, plus the interface headers, exceed the interface MTU.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.148.1.3.1.16

hwRsvpTeResvRSpecRate

Unsigned32

Read-only

If the requested service is Guaranteed, as specified by hwRsvpTeResvService, this is the clearing rate that is being requested. Otherwise, it is zero, or the agent may return noSuchValue.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.148.1.3.1.17

hwRsvpTeResvRSpecSlack

Integer32

Read-only

If the requested service is Guaranteed, as specified by hwRsvpTeResvService, this is the delay slack. Otherwise, it is zero, or the agent may return noSuchValue.

The value is always set as constant.

1.3.6.1.4.1.2011.5.25.148.1.3.1.18

hwRsvpTeResvInterval

Integer32

Read-only

The interval between refresh messages as advertised by the Next Hop.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.148.1.3.1.20

hwRsvpTeResvShared

INTEGER{true(1),false(2)}

Read-only

If TRUE, a reservation shared among senders is requested. If FALSE, a reservation specific to this sender is requested.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.148.1.3.1.21

hwRsvpTeResvExplicit

INTEGER{true(1),false(2)}

Read-only

If TRUE, individual senders are listed using Filter Specifications. If FALSE, all senders are implicitly selected. The Scope Object will contain a list of senders that need to receive this reservation request for the purpose of routing the RESV message.

The value is always set as false.

1.3.6.1.4.1.2011.5.25.148.1.3.1.22

hwRsvpTeResvRsvpHop

INTEGER{true(1),false(2)}

Read-only

If TRUE, the node believes that the previous IP hop is an RSVP hop. If FALSE, the node believes that the previous IP hop may not be an RSVP hop.

The value is always set as true.

1.3.6.1.4.1.2011.5.25.148.1.3.1.24

hwRsvpTeResvTtl

Integer32

Read-only

The TTL value in the RSVP header that was last received.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.148.1.3.1.25

hwRsvpTeResvConfirm

OCTET STRING

Read-only

Receiver's address.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.148.1.4.1.1

hwRsvpTeResvFwdNumber

INTEGER (0..4294967295)

Not-accessible

The number of this reservation request. This is for SNMP Indexing purposes only and has no relationship to any protocol value.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.148.1.4.1.2

hwRsvpTeResvFwdType

INTEGER{dnsSession(1),finrstSession(2),fragSession(3),ftpSession(4),ftpDataSession(5),h225Session(6),h245Session(7),h323rtcpSession(8),h323rtpSession(9),h323t120Session(10),httpSession(11),hwccSession(12),icmpSession(13),ilsSession(14),netbiosdataSession(15),netbiosnameSession(16),netbiosSession(17),rasSession(18),rtcpSession(19),rtpSession(20),rtspSession(21),smtpSession(22),synSession(23),tcpSession(24),telnetSession(25),pptpSession(26),udpSession(27),qqSession(28),msnSession(29),userdefineSession(30),sipSession(31),siprtpSession(32),siptrcpSession(33),greSesion(34)}

Read-only

The type of session (IPv4, IPv6, IPv6 with flow information, etc).

Only IPv4 is supported.

1.3.6.1.4.1.2011.5.25.148.1.4.1.3

hwRsvpTeResvFwdDestAddr

OCTET STRING

Read-only

The destination address used by all senders in this session.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.148.1.4.1.4

hwRsvpTeResvFwdSenderAddr

OCTET STRING

Read-only

The source address of the sender selected by this reservation. The value of all zeroes indicates 'all senders'.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.148.1.4.1.5

hwRsvpTeResvFwdDestAddrLength

Integer32

Read-only

The length of the destination address in bits. This is the CIDR Prefix Length, which is 32 bits for IPv4 hosts and multicast addresses.

The value is 32.

1.3.6.1.4.1.2011.5.25.148.1.4.1.6

hwRsvpTeResvFwdSenderAddrLength

Integer32

Read-only

The length of the sender's address in bits. This is the CIDR Prefix Length, which for is 32 bits IPv4 hosts and multicast addresses.

The value is 32.

1.3.6.1.4.1.2011.5.25.148.1.4.1.7

hwRsvpTeResvFwdHopAddr

OCTET STRING

Read-only

The address of the (previous) RSVP that will receive this message.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.148.1.4.1.8

hwRsvpTeResvFwdHopLih

Integer32

Read-only

The Logical Interface Handle sent to the (previous) RSVP that will receive this message.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.148.1.4.1.9

hwRsvpTeResvFwdInterface

Integer32

Read-only

The ifIndex value of the interface on which this RESV message was most recently sent.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.148.1.4.1.10

hwRsvpTeResvFwdService

INTEGER {bestEffort (1),guaranteedDelay (2),controlledLoad (5)}

Read-only

The QoS Service classification requested.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.148.1.4.1.11

hwRsvpTeResvFwdTSpecRate

Unsigned32

Read-only

The Average Bit Rate of the sender's data stream. Within a transmission burst, the arrival rate may be as fast as hwRsvpTeResvFwdTSpec-PeakRate (if supported by the service model); however, averaged across two or more burst intervals, the rate should not exceed hwRsvpTeResvFwdTSpecRate.

Note that this is a prediction, often based on the general capability of a type of codec or particular encoding; the measured average rate may be significantly lower.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.148.1.4.1.12

hwRsvpTeResvFwdTSpecPeakRate

Unsigned32

Read-only

The Peak Bit Rate of the sender's data stream Traffic arrival is not expected to exceed this rate at any time, apart from the effects of jitter in the network. If not specified in the TSpec, this returns zero or noSuchValue.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.148.1.4.1.13

hwRsvpTeResvFwdTSpecBurst

INTEGER

Read-only

The size of the largest burst expected from the sender at a time. If this is less than the sender's advertised burst size, the receiver is asking the network to provide flow pacing beyond what would be provided under normal circumstances. Such pacing is at the network's option.

The value is always set as constant.

1.3.6.1.4.1.2011.5.25.148.1.4.1.14

hwRsvpTeResvFwdTSpecMinTu

Integer32 (0..'7FFFFFFF'h)

Read-only

The minimum message size for this flow. The policing algorithm will treat smaller messages as though they are this size.

The value is always set as constant.

1.3.6.1.4.1.2011.5.25.148.1.4.1.15

hwRsvpTeResvFwdTSpecMaxTu

Integer32 (0..'7FFFFFFF'h)

Read-only

The maximum message size for this flow. The admission algorithm will reject TSpecs whose Maximum Transmission Unit, plus the interface headers, exceed the interface MTU.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.148.1.4.1.16

hwRsvpTeResvFwdRSpecRate

Unsigned32

Read-only

If the requested service is Guaranteed, as specified by hwRsvpTeResvService, This is the clearing rate that is being requested. Otherwise, it is zero, or the agent may return noSuchValue.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.148.1.4.1.17

hwRsvpTeResvFwdRSpecSlack

Integer32

Read-only

If the requested service is Guaranteed, as specified by hwRsvpTeResvService, this is the delay slack. Otherwise, it is zero, or the agent may return noSuchValue.

The value is always set as constant.

1.3.6.1.4.1.2011.5.25.148.1.4.1.18

hwRsvpTeResvFwdInterval

Integer32

Read-only

The interval between refresh messages advertised to the Previous Hop.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.148.1.4.1.20

hwRsvpTeResvFwdShared

INTEGER{true(1),false(2)}

Read-only

If TRUE, a reservation shared among senders is requested. If FALSE, a reservation specific to this sender is requested.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.148.1.4.1.21

hwRsvpTeResvFwdExplicit

INTEGER{true(1),false(2)}

Read-only

If TRUE, individual senders are listed using Filter Specifications. If FALSE, all senders are implicitly selected. The Scope Object will contain a list of senders that need to receive this reservation request for the purpose of routing the RESV message.

The value is always set as false.

1.3.6.1.4.1.2011.5.25.148.1.4.1.22

hwRsvpTeResvFwdRsvpHop

INTEGER{true(1),false(2)}

Read-only

If TRUE, the node believes that the next IP hop is an RSVP hop. If FALSE, the node believes that the next IP hop may not be an RSVP hop.

The value is always set as true.

1.3.6.1.4.1.2011.5.25.148.1.4.1.24

hwRsvpTeResvFwdTtl

Integer32

Read-only

The TTL value in the RSVP header that was last received.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.148.1.4.1.25

hwRsvpTeResvFwdMsgIdFlag

Integer32

Read-only

Indicates that the message sender requests the peer to send an acknowledgment for the message (1: ACK desired.).

The value is always set as constant.

1.3.6.1.4.1.2011.5.25.148.1.4.1.26

hwRsvpTeResvFwdMsgIdEpoch

INTEGER (0..4294967295)

Read-only

A value that indicates when the Message_Identifier sequence has been reset.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.148.1.4.1.27

hwRsvpTeResvFwdMsgIdNumber

INTEGER (0..4294967295)

Read-only

When combined with the message generator's IP address, the Message_Identifier field uniquely identifies a message. The values placed in this field change incrementally and only decrease when the Epoch changes or when the value wraps.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.148.1.5.1.1

hwRsvpTeIfUdpNbrs

INTEGER (0..4294967295)

Read-only

The number of neighbors perceived to be using only the RSVP UDP Encapsulation.

The value is always set as 0.

1.3.6.1.4.1.2011.5.25.148.1.5.1.2

hwRsvpTeIfIpNbrs

INTEGER (0..4294967295)

Read-only

The number of neighbors perceived to be using only the RSVP IP Encapsulation.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.148.1.5.1.3

hwRsvpTeIfNbrs

INTEGER (0..4294967295)

Read-only

The number of neighbors currently perceived; this will exceed hwRsvpTeIfIpNbrs + hwRsvpTeIfUdpNbrs by the number of neighbors using both encapsulations.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.148.1.5.1.4

hwRsvpTeIfRefreshBlockadeMultiple

Integer32

Read-only

The value of the RSVP value 'Kb', Which is the minimum number of refresh intervals that blockade state will last once entered.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.148.1.5.1.5

hwRsvpTeIfRefreshMultiple

Integer32

Read-only

The value of the RSVP value 'K', which is the number of refresh intervals which must elapse (minimum) before a PATH or RESV message which is not being refreshed will be aged out.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.148.1.5.1.6

hwRsvpTeIfTtl

Integer32

Read-only

The value of SEND_TTL used on this interface for messages this node originates. If set to zero, the node determines the TTL via other means.

The value is always set as 16.

1.3.6.1.4.1.2011.5.25.148.1.5.1.7

hwRsvpTeIfRefreshInterval

INTEGER (0..2147483647)

Read-only

The value of the RSVP value 'R', which is the minimum period between refresh transmissions of a given PATH or RESV message on an interface.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.148.1.5.1.8

hwRsvpTeIfRouteDelay

INTEGER (0..2147483647)

Read-only

The approximate period from the time a route is changed to the time a resulting message appears on the interface.

The value is always set as 200.

1.3.6.1.4.1.2011.5.25.148.1.5.1.9

hwRsvpTeIfEnabled

INTEGER{true(1),false(2)}

Read-only

Its value is always TRUE, if RSVP is enabled on this Interface.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.148.1.5.1.10

hwRsvpTeIfUdpRequired

INTEGER{true(1),false(2)}

Read-only

If TRUE, manual configuration forces the use of UDP encapsulation on the interface. If FALSE, UDP encapsulation is only used if hwRsvpTeIfUdpNbrs is not zero.

The value is always set as false.

1.3.6.1.4.1.2011.5.25.148.1.5.1.11

hwRsvpTeIfStatus

INTEGER{active(1),notInService(2),notReady(3),createAndGo(4),createAndWait(5),destroy(6)}

Read-only

'Active' on interfaces that are configured for RSVP.

The value is always set as 1.

1.3.6.1.4.1.2011.5.25.148.1.5.1.12

hwRsvpTeIfHelloEnabled

INTEGER{true(1),false(2)}

Read-only

If TRUE, RSVPTE hello is enabled on this Interface. If FALSE, RSVPTE is not enabled on this interface.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.148.1.5.1.13

hwRsvpTeIfSrefreshEnabled

INTEGER{true(1),false(2)}

Read-only

If TRUE, Srefresh is enabled on this interface. If FALSE, Srefresh is not enabled on this interface.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.148.1.5.1.14

hwRsvpTeIfSrefreshInterval

INTEGER (0..2147483647)

Read-only

Interval between two updates.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.148.1.5.1.15

hwRsvpTeIfRetranIncDelta

Integer32

Read-only

Delta governs the speed with which the sender increases the retransmission interval. The ratio of two successive retransmission intervals is (1 + Delta).

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.148.1.5.1.16

hwRsvpTeIfRetranInterval

INTEGER (0..2147483647)

Read-only

The retransmission interval.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.148.1.5.1.17

hwRsvpTeIfAuthEnabled

INTEGER{true(1),false(2)}

Read-only

If TRUE, Authentication is enabled on this Interface. If FALSE, Authentication is not enabled on this interface.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.148.1.5.1.18

hwRsvpTeIfAuthEncrypted

INTEGER{true(1),false(2)}

Read-only

This states that Authentication key is encrypted or not.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.148.1.5.1.19

hwRsvpTeIfAuthHandshake

INTEGER{true(1),false(2)}

Read-only

Handshaking is enabled authentications.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.148.1.5.1.20

hwRsvpTeIfAuthLifeTime

INTEGER (0..2147483647)

Read-only

Authentication life time.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.148.1.5.1.21

hwRsvpTeIfAuthKey

OCTET STRING (SIZE (0..392))

Read-only

Authentication key, used for authentication processing. For security purposes, a get on this returns a zero length string.

Currently, the value range of 1 to 64 is supported.

1.3.6.1.4.1.2011.5.25.148.1.5.1.22

hwRsvpTeIfWindowSize

Integer32

Read-only

Administrators can specify a message window corresponding to the worst case reordering behavior. For example, one might specify that packets reordered within a 32 message window would be accepted. If no reordering can occur, the window is set to one. The maximum value is 64.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.148.1.6.1.1

hwRsvpTeNbrAddress

OCTET STRING

Not-accessible

The IPv4 or IPv6 Address used by this neighbor. This object may not be changed when the value of the Row Status object is 'active'.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.148.1.6.1.2

hwRsvpTeNbrProtocol

INTEGER

Read-only

The encapsulation being used by this neighbor.

The value is always set as 1.

1.3.6.1.4.1.2011.5.25.148.1.6.1.3

hwRsvpTeNbrStatus

INTEGER{active(1),notInService(2),notReady(3),createAndGo(4),createAndWait(5),destroy(6)}

Read-only

'Active' for all neighbors. This object may be used to configure neighbors. In the presence of configured neighbors, the implementation may (but is not required to) limit the set of valid neighbors to those configured.

The value is always set as 1.

1.3.6.1.4.1.2011.5.25.148.1.6.1.4

hwRsvpTeNbrSendersNumber

INTEGER (0..4294967295)

Read-only

The number of senders on the Neighbor.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.148.1.6.1.5

hwRsvpTeNbrReceiversNumber

INTEGER (0..4294967295)

Read-only

The number of receivers on the Neighbor.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.148.1.6.1.6

hwRsvpTeNbrHelloEnabled

INTEGER{true(1),false(2)}

Read-only

If TRUE hello is enabled on the neighbor.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.148.1.6.1.7

hwRsvpTeNbrHelloSrcInstance

INTEGER (0..4294967295)

Read-only

Source instance of the neighbor.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.148.1.6.1.8

hwRsvpTeNbrHelloDstInstance

INTEGER (0..4294967295)

Read-only

Destination instance of the neighbor.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.148.1.6.1.9

hwRsvpTeNbrHelloLostCounter

INTEGER (0..4294967295)

Read-only

The number of times the hello messages have been sent to the neighbor for which hello ACK has not received yet.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.148.1.6.1.10

hwRsvpTeNbrHelloType

INTEGER

Read-only

Hello type that is being sent to the neighbor.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.148.1.6.1.11

hwRsvpTeNbrGrCapability

Integer32

Read-only

Gives neighbor capability to support GR or undergo GR, in case of control plane restart. A mixed value.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.148.1.6.1.12

hwRsvpTeNbrGrRestartTime

TimeTicks

Read-only

Neighbor nodes GR restart time value.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.148.1.6.1.13

hwRsvpTeNbrGrRecoveryTime

TimeTicks

Read-only

Neighbor nodes GR recovery time value.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.148.1.6.1.14

hwRsvpTeNbrGrStatus

INTEGER

Read-only

Neighbor nodes GR status.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.148.1.6.1.15

hwRsvpTeNbrAuthKeyId

OCTET STRING

Read-only

Neighbor's authentication key, used for authentication processing. A return of null string indicates the absence of the item. For security purposes, a get on this returns a zero length string.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.148.1.6.1.16

hwRsvpTeNbrReductionEnabled

INTEGER{true(1),false(2)}

Read-only

If TRUE srefresh is enabled on the neighbor, else srefresh is not enabled on the neighbor.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.148.1.6.1.17

hwRsvpTeNbrReliabilityEnabled

INTEGER{true(1),false(2)}

Read-only

If TRUE reliability is enabled on the neighbor, else reliability is not enabled on the neighbor.

1.3.6.1.4.1.2011.5.25.148.1.7.1.1

hwRsvpTeMessageIdEpoch

INTEGER (0..4294967295)

Not-accessible

A value that indicates when the Message_Identifier sequence has been reset.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.148.1.7.1.2

hwRsvpTeMessageIdNumber

INTEGER (0..4294967295)

Not-accessible

When combined with the message generator's IP address, the Message_Identifier field uniquely identifies a message. The values placed in this field change incrementally and only decrease when the Epoch changes or when the value wraps.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.148.1.7.1.3

hwRsvpTeMessageIdFlag

INTEGER

Read-only

An enumerable value to indicate the type of this Message_Identifier.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.148.1.8.1.1

hwRsvpTeFilterSpecNumber

INTEGER (0..4294967295)

Not-accessible

The number of this Filter_Spec. This is for SNMP Indexing purposes only and has no relationship to any protocol value.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.148.1.8.1.2

hwRsvpTeFilterSpecLspId

Integer32

Read-only

A 16-bit identifier used in the SENDER_TEMPLATE and the FILTER_SPEC that can be changed to allow a sender to share resources with itself.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.148.1.8.1.3

hwRsvpTeFilterSpecIngressLsrId

OCTET STRING

Read-only

IP address for a sender node.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.148.1.8.1.4

hwRsvpTeFilterSpecLabel

INTEGER (0..4294967295)

Read-only

The value of the label arranged by next hop. A return of 4294967295 indicates the absence of the item.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.148.1.9.1.1

hwRsvpTeRroNumber

INTEGER (0..4294967295)

Not-accessible

The number of this RRO sub-object. This is for SNMP Indexing purposes only and has no relationship to any protocol value.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.148.1.9.1.2

hwRsvpTeRroType

INTEGER

Read-only

An enumerable value that indicates the type of this sub-object.

IPv4 and Label are supported. IPv6 is not supported.

1.3.6.1.4.1.2011.5.25.148.1.9.1.3

hwRsvpTeRroIpAddr

OCTET STRING

Read-only

IP address for this sub-object if the type is 'IPv4 address' of 'IPv6 address'. A return of null string indicates the absence of the item.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.148.1.9.1.4

hwRsvpTeRroIpPrefixLen

Integer32

Read-only

IP prefix length for this sub-object if the type is 'IPv4 address' of 'IPv6 address'. A return of 0 indicates the absence of the item.

Only IPv4 is supported.

1.3.6.1.4.1.2011.5.25.148.1.9.1.5

hwRsvpTeRroLabel

INTEGER (0..4294967295)

Read-only

The value of the label if the type is 'Label'. A return of 4294967295 indicates the absence of the item.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.148.1.9.1.6

hwRsvpTeRroFlag

Integer32

Read-only

If hwRsvpTeRroType is IPv4 or IPv6, it is a mixed value.

If hwRsvpTeRroType is Label, 0x01 means global label. A return of zero indicates no bit was set.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.148.1.10.1.1

hwRsvpTeEroNumber

INTEGER (0..4294967295)

Not-accessible

The number of this ERO sub-object. This is for SNMP Indexing purposes only and has no relationship to any protocol value.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.148.1.10.1.2

hwRsvpTeEroType

INTEGER

Read-only

An enumerable value that indicates the type of this sub-object.

Only IPv4 is supported.

1.3.6.1.4.1.2011.5.25.148.1.10.1.3

hwRsvpTeEroIpAddr

OCTET STRING

Read-only

IP address for this sub-object.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.148.1.10.1.4

hwRsvpTeEroIpPrefixLen

Integer32

Read-only

IP prefix length for this sub-object.

Only IPv4 is supported.

1.3.6.1.4.1.2011.5.25.148.1.12.2.1

hwRsvpTeHelloLost

hwRsvpTeNbr

Indicates neighbor of RSVP hello lost.

This object is implemented as defined in the corresponding MIB file.

1.3.6.1.4.1.2011.5.25.148.1.12.2.2

hwRsvpTeHelloLostRecovery

hwRsvpTeNbr

Indicates neighbor of RSVP hello lost recovery.

This object is implemented as defined in the corresponding MIB file.

1.3.6.1.4.1.2011.5.25.148.1.12.2.3

hwRsvpTeAuthFail

hwRsvpTeNbr

Indicates authentication of RSVP neighbor was wrong.

This object is implemented as defined in the corresponding MIB file.

1.3.6.1.4.1.2011.5.25.148.1.12.2.4

hwRsvpTeAuthSuccess

hwRsvpTeNbr

Indicates authentication of RSVP neighbor was ok.

This object is implemented as defined in the corresponding MIB file.

1.3.6.1.4.1.2011.5.25.148.1.12.2.5

hwRsvpTeIfNbrThresholdExceed

• hwRsvpTeIfName

• hwRsvpTeIfNbrCurrentCount

• hwRsvpTeIfNbrThreshold

• hwRsvpTeIfNbrTotalCount

This object indicates that the proportion of configured RSVP neighbors to RSVP neighbors supported by a device reaches the upper threshold.

This object is implemented as defined in the corresponding MIB file.

1.3.6.1.4.1.2011.5.25.148.1.12.2.6

hwRsvpTeIfNbrThresholdExceedClear

hwRsvpTeIfName

This object indicates that the proportion of configured RSVP neighbors to RSVP neighbors supported by a device falls below the lower threshold.

This object is implemented as defined in the corresponding MIB file.

1.3.6.1.4.1.2011.5.25.148.1.12.2.7

hwRsvpTeIfNbrTotalCountExceed

• hwRsvpTeIfName

• hwRsvpTeIfNbrTotalCount

This object indicates that the number of configured RSVP neighbors on a device reaches the maximum number of RSVP neighbors supported by the device.

This object is implemented as defined in the corresponding MIB file.

1.3.6.1.4.1.2011.5.25.148.1.12.2.8

hwRsvpTeIfNbrTotalCountExceedClear

hwRsvpTeIfName

This object indicates that the number of configured RSVP neighbors on a device falls below 95% of the maximum number of RSVP neighbors.

This object is implemented as defined in the corresponding MIB file.