No relevant resource is found in the selected language.
Enterprise
Worldwide
Search
Support Documentation
S1700, S2720, S5700, and S6700 V200R019C10 Alarm Handling

This document provides the explanations, causes, and recommended actions of alarms on the product.

Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
LACP

LACP

LACP_1.3.6.1.4.1.2011.5.25.41.3.2 hwLacpNegotiateFailed

Description

LACP/2/MNCD:OID [oid] The member of LAG neither can take over PDU nor transmit PDUs. (TrunkIndex=[INTEGER], PortIfIndex=[INTEGER], TrunkId=[INTEGER], TrunkName=[OCTET], PortName=[OCTET])

Negotiations over member links failed.

Attribute

Alarm ID Alarm Severity Alarm Type
1.3.6.1.4.1.2011.5.25.41.3.2 Major operationalViolation(8)

Parameters

Name Meaning

oid

Indicates the MIB object ID of the alarm.

TrunkIndex

Indicates the index of a Trunk.

PortIfIndex

Indicates the index of a member interface.

TrunkId

Indicates the ID of a Trunk interface.

TrunkName

Indicates the name of a Trunk interface.

PortName

Indicates the name of a member interface.

Impact on the System

The link cannot transmit services.

Possible Causes

1.

An MNCD trap was generated when the link became Down.

2.

No LACP packet was received from the remote end when the timer expired.

3.

A member interface left the LAG.

4.

The interface received the LACP packet sent from the interfaces on the same device.

Procedure

  1. Run the display this interface command on the corresponding interface to check whether the interface is Down.

    • If so, go to Step 2.

    • If not, go to Step 4.

  2. Run the undo shutdown command to check whether the alarm is cleared.

    • If the alarm is cleared, go to Step 8.

    • If the alarm is not cleared, go to Step 3.

  3. Check whether the physical link is faulty.

    • If so, go to Step 6.

    • If not, go to Step 4.

  4. Run the display eth-trunk command to check whether there is an interface on the local or remote end of the link leaving the LAG.

    • If so, go to Step 5.

    • If not, go to Step 7.

  5. Check whether the interface leaves the LAG normally.

    • If so, go to Step 8.

    • If not, go to Step 7.

  6. Repair the physical link and then check whether the alarm is cleared.

    • If the alarm is cleared, go to Step 8.

    • If the alarm is not cleared, go to Step 4.

  7. Collect alarm information and configuration information, and then contact technical support personnel.
  8. End.

Related Information

None.

LACP_1.3.6.1.4.1.2011.5.25.41.3.3 hwLacpTotalLinkLoss

Description

LACP/2/TLL:OID [oid] Link bandwidth lost totally. (TrunkIndex=[INTEGER], TrunkIfIndex=[INTEGER], TrunkId=[INTEGER], TrunkName=[OCTET])

All the link bandwidths were lost.

Attribute

Alarm ID Alarm Severity Alarm Type
1.3.6.1.4.1.2011.5.25.41.3.3 Major operationalViolation(8)

Parameters

Name Meaning

oid

Indicates the MIB object ID of the alarm.

TrunkIndex

Indicates the index of a Trunk.

TrunkIfIndex

The value of this object identifies the index of a Trunk interface.

TrunkId

Indicates the ID of a Trunk interface.

TrunkName

Indicates the name of a Trunk interface.

Impact on the System

Services are interrupted.

Possible Causes

A TLL trap was generated when all links between two devices were disconnected and packets failed to be forwarded.

Procedure

  1. Run the display interface brief command to check whether the interface is Down.

    • If the alarm is cleared, go to Step 2

    • If the alarm is not cleared, go to Step 4

  2. Run the undo shutdown command to check whether the alarm is cleared.

    • If the alarm is cleared, go to Step 10.

    • If the alarm is not cleared, go to Step 3.

  3. Check whether the physical link is faulty.

    • If so, go to Step 7.

    • If not, go to Step 4.

  4. Run the display eth-trunk [ trunk-id [ interface interface-type interface-number | verbose ] ] command to check whether there are member interfaces in the LAG.

    • If so, go to Step 5.

    • If not, go to Step 8.

  5. Run the display trunkmembership eth-trunk trunk-id command to check whether the lower threshold of Eth-Trunk member links that can be Up in the LAG is correctly set. (An incorrect lower threshold causes the negotiation failure between the Eth-Trunk member interfaces.)

    • If so, go to Step 6.

    • If not, go to Step 9.

  6. In the Eth-Trunk interface view, run the least active-linknumber link-number command to correctly set the lower threshold of Trunk member links that can be Up. Then, check whether the fault is rectified.

    • If the alarm is cleared, go to Step 10.

    • If the alarm is cleared, go to Step 9.

  7. Repair the physical link and then check whether the alarm is cleared.

    • If the alarm is cleared, go to Step 10.

    • If the alarm is not cleared, go to Step 4.

  8. Run the eth-trunk trunk-id command in the interface view and add the current Ethernet interface to the Eth-Trunk interface as required. Then, check whether the alarm is cleared.

    • If the alarm is cleared, go to Step 10.

    • If the alarm is not cleared, go to Step 5.

  9. Collect alarm information and configuration information, and then contact technical support personnel.
  10. End.

Related Information

None.

LACP_1.3.6.1.4.1.2011.5.25.41.3.4 hwLacpPartialLinkLoss

Description

LACP/2/PLL:OID [OID] Link bandwidth lost partly. (TrunkIndex=[INTEGER], TrunkIfIndex=[INTEGER], TrunkId=[INTEGER], TrunkName=[OCTET])

The bandwidths of a link were partially lost.

Attribute

Alarm ID Alarm Severity Alarm Type
1.3.6.1.4.1.2011.5.25.41.3.4 Major operationalViolation(8)

Parameters

Name Meaning

oid

Indicates the MIB object ID of the alarm.

TrunkIndex

Indicates the index of a Trunk.

TrunkIfIndex

Indicates the index of a Trunk interface.

TrunkId

Indicates the ID of a Trunk interface.

TrunkName

Indicates the name of a Trunk interface.

Impact on the System

Part of services were interrupted.

Possible Causes

The number of the Eth-Trunk member links that were Up was smaller than the lower threshold value that was set, which caused the LAG to become Down. As a result, a PLL trap was generated.

Procedure

  1. Run the display interface brief command to check whether the interface is Down.

    • If so, go to Step 2.

    • If not, go to Step 4.

  2. Run the undo shutdown command to check whether the alarm is cleared.

    • If the alarm is cleared, go to Step 10.

    • If the alarm is not cleared, go to Step 3.

  3. Check whether the physical link is faulty.

    • If so, go to Step 7.

    • If not, go to Step 4.

  4. Run the display eth-trunk [ trunk-id [ interface interface-type interface-number | verbose ] ] command to check whether there are member interfaces in the LAG.

    • If so, go to Step 5.

    • If not, go to Step 8.

  5. Run the display trunkmembership eth-trunk trunk-id command to check whether the lower threshold for Eth-Trunk member links is set in the LAG; whether the number of Eth-Trunk member links that are successfully negotiated is smaller than the lower threshold for the Eth-Trunk member links that can be Up.

    • If so, go to Step 6.

    • If not, go to Step 9.

  6. In the Eth-Trunk interface view, run the least active-linknumber link-number command to correctly set the lower threshold of Trunk member links that can be Up. Then, check whether the alarm is cleared.

    • If the alarm is cleared, go to Step 10.

    • If the alarm is not cleared, go to Step 9.

  7. Repair the physical link and then check whether the alarm is cleared.

    • If the alarm is cleared, go to Step 10.

    • If the alarm is not cleared, go to Step 4.

  8. Run the eth-trunk trunk-id command in the interface view and add the current Ethernet interface to the Eth-Trunk interface as required. Then, check whether the alarm is cleared.

    • If the alarm is cleared, go to Step 10.

    • If the alarm is not cleared, go to Step 5.

  9. Collect alarm information and configuration information, and then contact technical support personnel.
  10. End.

Related Information

None.

LACP_1.3.6.1.4.1.2011.5.25.41.3.13 hwLacpNegotiateResume

Description

LACP/2/MNCR:OID [oid] Link negotiation failure is resumed. (TrunkIndex=[INTEGER], PortIfIndex=[INTEGER], TrunkId=[INTEGER], TrunkName=[OCTET], PortName=[OCTET])

It is the trap indicating the successful member link negotiation and is a matching trap of hwLacpNegotiateFailed.

Attribute

Alarm ID Alarm Severity Alarm Type
1.3.6.1.4.1.2011.5.25.41.3.13

Major

 operationalViolation(8)

Parameters

Name Meaning

oid

Indicates the MIB object ID of the alarm.

TrunkIndex

Indicates the index of a trunk.

PortIfIndex

Indicates the index of a member interface.

TrunkId

Indicates the ID of a trunk interface.

TrunkName

Indicates the name of a trunk interface.

PortName

Indicates the name of a member interface.

Impact on the System

The link can transmit services.

Possible Causes

1.

Member links negotiation succeeded for the first time.

2.

When the member link negotiation failed, the trap hwLacpNegotiateFailed was generated. After the fault was rectified, the trap hwLacpNegotiateResume was generated.

Procedure

  • This alarm message is informational only, and no action is required.

Related Information

LACP_1.3.6.1.4.1.2011.5.25.41.3.2 hwLacpNegotiateFailed

LACP_1.3.6.1.4.1.2011.5.25.41.3.14 hwLacpTotalLinkLossResume

Description

LACP/2/TLR:OID [oid] Link bandwidth lost totally is resumed. (TrunkIndex=[INTEGER], TrunkIfIndex=[INTEGER], TrunkId=[INTEGER], TrunkName=[OCTET])

It is a trap indicating the restoration of the total link bandwidth and is a matching trap of hwLacpTotalLinkLoss.

Attribute

Alarm ID Alarm Severity Alarm Type
1.3.6.1.4.1.2011.5.25.41.3.14

Major

 operationalViolation(8)

Parameters

Name Meaning

oid

Indicates the MIB object ID of the alarm.

TrunkIndex

Indicates the index of a trunk.

TrunkIfIndex

Indicates the index of a trunk interface.

TrunkId

Indicates the ID of a trunk interface.

TrunkName

Indicates the name of a trunk interface.

Impact on the System

Services are resumed.

Possible Causes

1.

The trap hwLacpTotalLinkLoss was generated when no interface was selected. When the fault was rectified, the trap hwLacpTotalLinkLossResume was generated.

Procedure

  • This alarm message is informational only, and no action is required.

Related Information

LACP_1.3.6.1.4.1.2011.5.25.41.3.3 hwLacpTotalLinkLoss

LACP_1.3.6.1.4.1.2011.5.25.41.3.15 hwLacpPartialLinkLossResume

Description

LACP/2/PLR:OID [oid] Link bandwidth lost partly is resumed. (TrunkIndex=[INTEGER], TrunkIfIndex=[INTEGER], TrunkId=[INTEGER], TrunkName=[OCTET])

It is a trap indicating the restoration of the partial link bandwidth and is a matching trap of hwLacpPartialLinkLoss.

Attribute

Alarm ID Alarm Severity Alarm Type
1.3.6.1.4.1.2011.5.25.41.3.15

Major

 operationalViolation(8)

Parameters

Name Meaning

oid

Indicates the MIB object ID of the alarm.

TrunkIndex

Indicates the index of a trunk.

TrunkIfIndex

Indicates the index of a trunk interface.

TrunkId

Indicates the ID of a trunk interface.

TrunkName

Indicates the name of a trunk interface.

Impact on the System

Part of services were resumed.

Possible Causes

1.

Because the number of trunk member links that could go Up through negotiation was below the minimum number of Up member links, the link aggregation group went Down, and thus the trap hwLacpPartialLinkLoss was generated. When the fault was rectified, the trap hwLacpPartialLinkLossResume was generated.

Procedure

  • This alarm message is informational only, and no action is required.

Related Information

LACP_1.3.6.1.4.1.2011.5.25.41.3.4 hwLacpPartialLinkLoss

LACP_1.3.6.1.4.1.2011.5.25.41.3.34 hwLacpPartnerExpiredLoss

Description

LACP/2/PEL:OID [oid] The member of LAG receive expired PDU from partner. (TrunkIndex=[INTEGER], PortIfIndex=[INTEGER], TrunkId=[INTEGER], TrunkName=[OCTET], PortName=[OCTET])

The local end received a timeout packet from the remote end.

Attribute

Alarm ID Alarm Severity Alarm Type

1.3.6.1.4.1.2011.5.25.41.3.34

Major

other(1)

Parameters

Name Meaning

oid

Indicates the MIB object ID of the alarm.

TrunkIndex

Index of an Eth-Trunk interface in static LACP mode

PortIfIndex

Index of an Eth-Trunk member interface in static LACP mode

TrunkId

ID of an Eth-Trunk interface in static LACP mode

TrunkName

Name of an Eth-Trunk interface in static LACP mode

PortName

Name of an Eth-Trunk member interface in static LACP mode

Impact on the System

Partial or all link bandwidth will lose, causing partial or all services to be interrupted.

Possible Causes

The remote end could not receive the LACP packet from the local end.

Procedure

  • If both local and remote ends are Huawei Datacom devices, see the troubleshooting procedures in LACP_1.3.6.1.4.1.2011.5.25.41.3.2 hwLacpNegotiateFailed.
    1. Check whether the interface is Down.

      • If so, go to Step 2.

      • If not, go to Step 4.

    2. Run the undo shutdown command to check whether the alarm is cleared.

      • If the alarm is cleared, go to Step 8.

      • If the alarm is not cleared, go to Step 3.

    3. Check whether the physical link is faulty.

      • If so, go to Step 6.

      • If not, go to Step 4.

    4. Check whether there is an interface on the local or remote end of the link leaving the LAG.

      • If so, go to Step 5.

      • If not, go to Step 7.

    5. Check whether the interface leaves the LAG normally.

      • If so, go to Step 8.

      • If not, go to Step 7.

    6. Repair the physical link and then check whether the alarm is cleared.

      • If the alarm is cleared, go to Step 8.

      • If the alarm is not cleared, go to Step 4.

    7. Collect alarm information and configuration information, and then contact technical support personnel.
    8. End.
  • If the local end is a Huawei Datacom device, but the remote end is a non-Huawei Datacom device, contact technical personnel from the device's manufacturer.

LACP_1.3.6.1.4.1.2011.5.25.41.3.35 hwLacpPDUChange

Description

LACP/2/PDUC: OID [oid] The LACP member interface's status changed from selected to unselected due to the PDU change. (TrunkIndex=[INTEGER], PortIfIndex=[INTEGER], TrunkId=[INTEGER], TrunkName=[OCTET], PortName=[OCTET], OldPduInfo=[OCTET], NewPduInfo=[OCTET], ReasonCode=[OCTET])

The status of a member interface of an Eth-Trunk interface in static LACP mode changed from selected to not selected due to an LACPDU change.

Attribute

Alarm ID Alarm Severity Alarm Type

1.3.6.1.4.1.2011.5.25.41.3.35

Major

other

Parameters

Name Meaning

oid

Indicates the MIB object ID of the alarm.

TrunkIndex

Index of an Eth-Trunk interface in static LACP mode.

PortIfIndex

Index of a member interface of an Eth-Trunk interface in static LACP mode.

TrunkId

ID of an Eth-Trunk interface in static LACP mode.

TrunkName

Name of an Eth-Trunk interface in static LACP mode.

PortName

Name of a member interface of an Eth-Trunk interface in static LACP mode.

OldPduInfo

Original LACPDU.

NewPduInfo

New LACPDU.

ReasonCode

Reason for the LACPDU change.

Impact on the System

The member link cannot carry services.

Possible Causes

Cause 1: Actor system ID changed in the received PDU

Procedure

  1. Run the display interface brief command to check whether the member interface is Down.

    • If the interface is Down, go to Step 2.

    • If the interface is Up, go to Step 4.

  2. Run the undo shutdown command and check whether the alarm is cleared.

    • If the alarm is cleared, go to Step 10.

    • If the alarm persists, go to Step 3.

  3. Check whether the physical link connecting to the member interface is faulty.

    • If the physical link is faulty, go to Step 7.

    • If the physical link is not faulty, go to Step 4.

  4. Run the display eth-trunk [ trunk-id [ interface interface-type interface-number | verbose ] ] command to check whether the remote Eth-Trunk has member interfaces.

    • If the remote Eth-Trunk has member interfaces, go to Step 5.

    • If the remote Eth-Trunk does not have member interface, go to Step 8.

  5. Run the display trunkmembership eth-trunk trunk-id command to check whether the minimum number of member interfaces that are in the Up state is configured and appropriate.

    • If the minimum number of member interfaces that are in the Up state is inappropriate, go to Step 6.

    • If the minimum number of member interfaces that are in the Up state is not configured, go to Step 9.

  6. Run the least active-linknumber link-number command in the Eth-Trunk interface view to configure an appropriate minimum number of member interfaces that are in the Up state. Then, check whether the alarm is cleared.

    • If the alarm is cleared, go to Step 10.

    • If the alarm persists, go to Step 9.

  7. Repair the physical link and check whether the alarm is cleared.

    • If the alarm is cleared, go to Step 10.

    • If the alarm persists, go to Step 4.

  8. Run the eth-trunk trunk-id command in an interface view to add the interface to the Eth-Trunk and check whether the alarm is cleared.

    • If the alarm is cleared, go to Step 10.

    • If the alarm persists, go to Step 5.

  9. Collect alarm information and configuration information, and then contact technical support personnel.
  10. End.

Related Information

LACP_1.3.6.1.4.1.2011.5.25.41.3.36 hwLacpPDUChangeResume

LACP_1.3.6.1.4.1.2011.5.25.41.3.36 hwLacpPDUChangeResume

Description

LACP/2/PDUR: OID [oid] The LACP member interface's status changed from unselected to selected. (TrunkIndex=[INTEGER], PortIfIndex=[INTEGER], TrunkId=[INTEGER], TrunkName=[OCTET], PortName=[OCTET])

The status of a member interface of an Eth-Trunk interface in static LACP mode changed from unselected to selected.

Attribute

Alarm ID Alarm Severity Alarm Type
1.3.6.1.4.1.2011.5.25.41.3.36 Major other

Parameters

Name Meaning
oid Indicates the MIB object ID of the alarm.
TrunkIndex Index of an Eth-Trunk interface in static LACP mode.
PortIfIndex Index of a member interface of an Eth-Trunk interface in static LACP mode.
TrunkId ID of an Eth-Trunk interface in static LACP mode.
TrunkName Name of an Eth-Trunk interface in static LACP mode.
PortName Name of a member interface of an Eth-Trunk interface in static LACP mode.

Impact on the System

The member link can carry services.

Possible Causes

Cause 1: Actor system ID changed in the received PDU.

Procedure

  • This alarm message is informational only, and no action is required.

Related Information

LACP_1.3.6.1.4.1.2011.5.25.41.3.35 hwLacpPDUChange

Translation
日本語 简体中文
Download
Updated: 2022-05-25

Document ID: EDOC1100127008

Views: 80694

Downloads: 335

Average rating:
This Document Applies to these Products

Related Version

Related Documents

Digital Signature File

Digital Signature Authentication Mode
Share
Previous Next

Copyright © 2023 Huawei Technologies Co., Ltd. All rights reserved.

You are going to visit :