IFPDT

IFPDT/1/CRCRATEEXCEED: OID [OID] The interface CRC error rate exceeded the trap threshold, which may affect forwarding. Handle it as soon as possible. (InterfaceIndex=[INTEGER], InterfaceName=[OCTET], CrcRate=[OCTET], TrapThreshold=[OCTET])

The rate of receiving CRC error packets equals or exceeds 1000 packets per second.

IFPDT/1/ERRORRATEEXCEED: OID [OID] The interface rate of incoming error packets exceeded the trap threshold, which may affect forwarding. Handle it as soon as possible. (InterfaceIndex=[INTEGER], InterfaceName=[OCTET], ErrorRate=[OCTET], TrapThreshold=[OCTET])

The rate at which an interface received CRC, Giants, and Runts error packets equaled or exceeded 1000 packets per second.

IFPDT/4/PORT_INBRDCAST: OID [oid] The rapid-change of input broadcast exceeded the threshold. (IfIndex=[INTEGER], InterfaceName=[STRING], InputBroadcastChangeThreshold=[INTEGER]pps, CurrentInputBroadcastRate=[COUNTER64]pps, BaseInputBroadcastRate=[COUNTER64]pps)

The difference (increase or decrease) in the broadcast traffic volume change in the inbound direction of interfaces exceeded the threshold.

IFPDT/1/CRCRATIOEXCEED:OID [OID] The ratio of incoming CRC packets on the interface exceeds the threshold. (InterfaceIndex=[INTEGER], InterfaceName=[OCTET], Threshold=[OCTET], StatisticsInterval=[INTEGER], CRCPackets=[COUNTER64], TotalInPackets=[COUNTER64])

The percentage of received CRC packets on an interface against all the received packets exceeds the alarm threshold.

IFPDT/4/CRCRATIORESUME: OID [OID] The ratio of incoming CRC packets on the interface falls below the threshold. (InterfaceIndex=[INTEGER], InterfaceName=[OCTET], Threshold=[OCTET], StatisticsInterval=[INTEGER], CRCPackets=[COUNTER64], TotalInPackets=[COUNTER64])

The percentage of received CRC packets on an interface against all the received packets is lower than the alarm threshold.

IFPDT/4/PORT_INRATECHG: OID [OID] The input rate change ratio exceeded the threshold. (IfIndex=[INTEGER], InterfaceName=[STRING], ThresholdPercent=[INTEGER]%, CurrentStatisticalPeriodRate=[COUNTER64], LastStatisticalPeriodRate=[COUNTER64])

The sudden traffic volume change percentage in the inbound direction of interfaces exceeded the trap threshold.

IFPDT/4/PORT_OUTRATECHG: OID [oid] The output rate change ratio exceeded the threshold. (IfIndex=[INTEGER], InterfaceName=[STRING], ThresholdPercent=[INTEGER]%, CurrentStatisticalPeriodRate=[COUNTER64], LastStatisticalPeriodRate=[COUNTER64])

The sudden traffic volume change percentage in the outbound direction of interfaces exceeded the trap threshold.

IFPDT/3/SUBIFNUMOVERSPEC: OID [OID] The number of subinterfaces on the switch exceeds the limit, which may cause an exception on the switch. (SubIfSpec=[INTEGER])

The number of sub-interfaces on the switch exceeds the maximum value.

IFPDT/4/SUBIFNUMNORMAL: OID [OID] The number of subinterfaces on the switch falls below the limit. (SubIfSpec=[INTEGER])

The number of sub-interfaces on the switch is less than or equal to the maximum value.

IFPDT/4/NOSUPPORT_OEPORT:OID [oid] The 1000base-T optical/electrical module or optical module cannot be installed on the port when the port is used as a stack port. (EntityPhysicalIndex=[INTEGER], EntityIfIndex=[INTEGER], EntPhysicalName=[OCTET], hwEntityTrapFaultID=[INTEGER])

A copper module or GE optical module cannot be used on a stack port.

IFPDT/3/MEMSPEEDDIF: OID [OID] The active member ports in trunk have inconsistent bandwidth. (TrunkIfIndex=[INTEGER], TrunkName=[OCTET])

The rates of active interfaces of the Eth-Trunk are different.

IFPDT/4/MEMSPEEDSAME: OID [OID] The active member ports in trunk have consistent bandwidth. (TrunkIfIndex=[INTEGER], TrunkName=[OCTET])

The rates of active interfaces of the Eth-Trunk are the same.

IFPDT/2/PROTGROUPUNAVAIL: OID [OID] The port protection group is unavailable. (PortProtectGroupId=[INTEGER])

The port protection group function becomes unavailable.

IFPDT/4/PROTGROUPAVAIL: OID [OID] The port protection group is available. (PortProtectGroupId=[INTEGER])

The port protection group function becomes available.

IFPDT/4/PROTGROUPDELETE: OID [OID] The port protection group was deleted. (PortProtectGroupId=[INTEGER])

The port protection group was deleted.

IFPDT/4/SNRABNORMAL:OID [oid] The current network cable is of poor quality, and there is a risk of packet loss. (InterfaceIndex=[INTEGER], InterfaceName=[OCTET])

The network cable quality is poor and packet loss may occur.

IFPDT/4/SNRNORMAL:OID [OID] The current network cable is of good quality. (InterfaceIndex=[INTEGER], InterfaceName=[OCTET])

The network cable quality is good.

IFPDT/4/SNRDETECTNOTSUPPORT:OID [OID] The port goes down, and the network cable quality cannot be detected. (InterfaceIndex=[INTEGER], InterfaceName=[OCTET])

The network cable quality cannot be checked.

IFPDT/4/VXLANHASHNOTSUPPORT:OID [oid] The Eth-Trunk cannot function normally as an outbound interface for vxlan packets when IP address-based load balancing is configured. (InterfaceIndex=[INTEGER], InterfaceName=[STRING])

When an Eth-Trunk functions as the outbound interface of VXLAN packets, the IP address-based load balancing mode configured on the Eth-Trunk does not take effect for VXLAN packets.

IFPDT/4/LRMABNORMAL: OID [OID] The interface does not support the LRM optical module. (InterfaceIndex=[INTEGER], InterfaceName=[OCTET])

The interface does not support LRM optical modules.

IFPDT/4/INDISCARDEXCEED:OID [OID] Interface input discard exceed the trap threshold. (InterfaceIndex=[INTEGER], InterfaceName=[OCTET], Statistics=[COUNTER64], TrapThreshold=[ULONG], TrapInterval=[ULONG](s))

The number of discarded incoming packets on an interface due to a network congestion exceeds the threshold.

IFPDT/4/OUTDISCARDEXCEED:OID [OID] Interface output discard exceed the trap threshold. (InterfaceIndex=[INTEGER], InterfaceName=[OCTET], Statistics=[COUNTER64], TrapThreshold=[ULONG], TrapInterval=[ULONG](s))

The number of discarded outgoing packets on an interface due to a network congestion exceeds the threshold.

IFPDT/4/TUNNELIFNUMOVERSPEC:OID [OID] The number of Tunnel interfaces exceeds the limit. (TunnelIfThreshold=[INTEGER], CurrentNum=[INTEGER])

The number of tunnel interfaces exceeded the upper limit.