WLAN

WLAN/5/STA_REACH_WARNING: OID [oid] The number of stations reaches 80% of the maximum specifications.(MaxStaNum=[INTEGER],CurStaNum=[INTEGER])

The number of online STAs reaches 80% of the maximum.

WLAN/4/STA_REACH_WARNING_RESTORE: OID [oid] The number of stations is less than 80% of the maximum specifications.(MaxStaNum =[INTEGER], CurStaNum=[INTEGER])

The number of online STAs falls below 80% of the maximum.

WLAN/4/STA_REACH_MAX: OID [oid] The number of stations reaches the maximum specifications.(MaxStaNum=[INTEGER],CurStaNum=[INTEGER])

The number of online STAs reaches the maximum.

WLAN/4/STA_REACH_MAX_RESTORE: OID [oid] The number of stations is less than the maximum specifications.(MaxStaNum =[INTEGER], CurStaNum=[INTEGER])

The number of online STAs falls below the maximum.

WLAN/4/SNR_NORMAL:OID [oid] The current network cable quality is good. (APMAC=[OPAQUE], APName=[STRING], InterfaceIndex=[INTEGER], InterfaceName=[OCTET], APID=[INTEGER])

The network cable quality is good.

WLAN/4/SNR_ABNORMAL:OID [oid] The current network cable quality is poor, causing packet loss risks.(APMAC=[OPAQUE], APName=[STRING], InterfaceIndex=[INTEGER], InterfaceName=[OCTET], APID=[INTEGER])

The network cable quality is poor and packet loss may occur.

WLAN/4/SNR_DETECT_NOTSUPPORT:OID [OID] The port is Down, resulting in a failure to detect the network cable quality. (APMAC=[OPAQUE], APName=[STRING], InterfaceIndex=[INTEGER], InterfaceName=[OCTET], APID=[INTEGER])

The network cable quality cannot be checked.

WLAN/4/SHARE_LICENSE_AGE:OID [oid] Shared licenses are aging, and this license will age after 29 days. (ACMAC=[OPAQU E], Number of shared licenses=[INTEGER])

Shared licenses age out.

WLAN/4/SHARE_LICENSE_AGE_RESTORE: OID [oid] Shared licenses stop aging. (ACMAC=[OPAQUE], Number of Shared licenses=[INTEGER])

The shared license aging stops.

WLAN/4/POOL_LICENSE_AGE: OID [oid] The license resource pool is aging. After the pool is aged, only the local AC license is valid. (Total number of licenses=[INTEGER], Number of local shared licenses=[INTEGER])

The license pool ages out.

WLAN/4/POOL_LICENSE_AGE_RESTORE: OID [oid] The license resource pool stops aging. (Total number of licenses=[INTEGER], Number of local Shared licenses=[INTEGER])

The license pool stops aging.

WLAN/4/WAPI_CERT_NEARLY_EXPIRED: OID [oid] The WAPI certificate is nearly expired. (SecurityProfileName=[STRING], CertType=[STRING], CertFileName=[STRING], CertStartTime=[STRING], CertEndTime=[STRING])

The validity period of the WAPI certificate loaded to the security profile is less than 30 days.

WLAN/4/WAPI_CERT_NEARLY_EXPIRED_RESTORE: OID [oid] The alarm of the WAPI certificate reaching expiration is cleared. (SecurityProfileName=[STRING], CertType=[STRING])

The alarm indicating that the validity period of the WAPI certificate loaded to the security profile is less than 30 days is cleared.

WLAN/2/WAPI_CERT_INVALID: OID [oid] The WAPI certificate is invalid. (SecurityProfileName=[STRING], CertType=[STRING], CertFileName=[STRING], CertStartTime=[STRING], CertEndTime=[STRING])

The WAPI certificate loaded to the security profile expires.

WLAN/6/WAPI_CERT_INVALID_RESTORE: OID [oid] The alarm of the WAPI certificate out of the invalidity period is cleared.(SecurityProfileName=[STRING], CertType=[STRING])

The alarm about the expiration of the WAPI certificate loaded to the security profile is cleared.

WLAN/2/AP_FAULT:OID [oid] AP changes to fault. (APMAC=[OPAQUE], APType=[STRING], APName=[STRING], APFAULTTIME=[INTEGER], APID=[INTEGER])

An RU goes offline.

WLAN/4/AP_NORMAL:OID [oid] The AP recovers or has been deleted. (APMAC=[OPAQUE], APType=[STRING], APName=[STRING], APID=[INTEGER])

An AP is recovered from a fault or is deleted.

WLAN/4/AP_PING_RESULT:OID [oid] AP ping result. (APMAC=[OPAQUE], APType=[STRING], APName=[STRING], SuccessCount=[INTEGER], FailureCount=[INTEGER]. AverageResponseTime=[INTEGER]ms. MinimumResponseTime=[INTEGER]ms, MaximumResponseTime=[INTEGER]ms, APID=[INTEGER])

The result of AP ping operations issued from the NMS to the AP is reported.

WLAN/4/AP_COMMIT_OVER:OID [oid] AP is committed over. (APMAC=[OPAQUE], APName=[STRING], APID=[INTEGER])

The AP configuration is committed.

WLAN/4/UNAUTHORIZED_AP_RECORD_EXIST:OID [oid] Unauthorized AP record exists.(Record number=[INTEGER])

An unauthorized AP alarm exists.

WLAN/4/UNAUTHORIZED_AP_RECORD_CLEAR:OID [oid] Unauthorized AP record clear.

The unauthorized AP alarm is cleared.

WLAN/4/AP_CPU_OVERLOAD: OID [oid] AP CPU overload notify. (APMAC=[OPAQUE], APName=[STRING], ApCpuRate=[INTEGER], the top three threads CPU occupancy are [STRING], APID=[INTEGER])

The AP's CPU usage exceeds the upper threshold.

WLAN/4/AP_CPU_OVERLOAD_RESTORE: OID [oid] AP CPU overload notify restore.(APMAC=[OPAQUE], APName=[STRING], ApCpuRate=[INTEGER], APID=[INTEGER])

The AP's CPU usage was restored to the allowed range.

WLAN/4/AP_MEM_OVERLOAD: OID [oid] AP memory overload notify.(APMAC=[OPAQUE], APName=[STRING], ApMemRate=[INTEGER], APID=[INTEGER])

The AP's memory usage exceeds the upper threshold.

WLAN/4/AP_MEM_OVERLOAD_RESTORE:OID [oid] AP memory overload notify restore.(APMAC=[OPAQUE], APName=[STRING], ApMemRate=[INTEGER], APID=[INTEGER])

The AP's memory usage was restored to the allowed range.

WLAN/4/AP_REACH_MAX_USERS:OID [oid] AP has the max number of stations notify.(APMAC=[OPAQUE], APName=[STRING], FailCause=[INTEGER], PermitNum=[INTEGER], APID=[INTEGER])

The maximum number of STAs associated with the AP was reached.

WLAN/4/AP_REACH_MAX_USERS_RESTORE:OID [oid] AP has the max number of stations notify restore.(APMAC=[OPAQUE], APName=[STRING], FailCause=[INTEGER], CurrentNum=[INTEGER], APID=[INTEGER])

The alarm about an AP's failure to connect STAs is cleared.

WLAN/4/AC_SYSTEM_SWITCH: OID [oid] AC has system switched notify.(APMAC=[OPAQUE], APName=[STRING], APSN=[OCTET], SwitchType=[INTEGER], APID=[INTEGER])

The active/standby switchover occurred on the AC.

WLAN/4/AP_DYING_GASP: OID [oid] Dying gasp notify.(APMAC=[OPAQUE], APName=[STRING], APID=[INTEGER])

The dying gasp alarm was generated.

This alarm is not supported by the AP4051TN, AP6052DN, AP7052DN, AP7152DN, AP7052DE, AP8050TN-HD, AP8082DN, and AP8182DN.

WLAN/4/AP_TEMPERATURE_TOO_LOW:OID [oid] The AP's temperature is too low. (APMAC=[OPAQUE], APName=[STRING], Temperature=[INTEGER]°C, APID=[INTEGER], TemperaturType=[STRING])

The AP's temperature is lower than the lower temperature alarm threshold.

WLAN/4/AP_TEMPERATURE_NORMAL:OID [oid] The AP's temperature changes to normal. (APMAC=[OPAQUE], APName=[STRING], Temperature=[INTEGER]°C, APID=[INTEGER], TemperaturType=[STRING])

The AP's temperature has increased above the lower temperature alarm threshold.

WLAN/4/AP_TEMPERATURE_TOO_HIGH:OID [oid] The AP's temperature is too high. (APMAC=[OPAQUE], APName=[STRING], Temperature=[INTEGER]°C, APID=[INTEGER], TemperaturType=[STRING])

The AP's temperature is higher than the upper temperature alarm threshold.

WLAN/4/AP_TEMPERATURE_NORMAL:OID [oid] The AP's temperature changes to normal. (APMAC=[OPAQUE], APName=[STRING], Temperature=[INTEGER]°C, APID=[INTEGER], TemperaturType=[STRING])

The AP's temperature has fallen below the upper temperature alarm threshold.

WLAN/4/AP_OPTICAL_RX_POWER_TOO_HIGH:OID [oid] AP optical module received power is too high notify. (APMAC=[OPAQUE], APName=[STRING], ApIfIndex=[INTEGER], Ap Optical RxPower=[INTEGER](0.1uw), ApEntityPhysicalName=[OCTET], APID=[INTEGER])

The receive power of the AP's optical module is higher than the upper power threshold.

WLAN/4/AP_OPTICAL_RX_POWER_TOO_HIGH_RESTORE:OID [oid] The receive power of the AP's optical module falls below the upper threshold. (APMAC=[MacAddress], APName=[STRING], ApIfIndex=[INTEGER], Ap Optical RxPower=[INTEGER](0.1uw), ApEntityPhysicalName=[OCTET], APID=[INTEGER])

The receive power of the AP's optical module has fallen below the upper power threshold.

WLAN/4/AP_OPTICAL_RX_POWER_TOO_LOW:OID [oid] AP optical module received power is too low notify. (APMAC=[MacAddress], APName=[STRING], ApIfIndex=[INTEGER], Ap Optical RxPower=[INTEGER](0.1uw), ApEntityPhysicalName=[OCTET], APID=[INTEGER])

The receive power of the AP's optical module is lower than the lower power threshold.

WLAN/4/AP_OPTICAL_RX_POWER_TOO_LOW_RESTORE:OID [oid] The receive power of the AP's optical module increases above the lower threshold.(APMAC=[MacAddress], APName=[STRING], ApIfIndex=[INTEGER], Ap Optical RxPower=[INTEGER](0.1uw), ApEntityPhysicalName=[OCTET], APID=[INTEGER])

The receive power of the AP's optical module has increased above the lower power threshold.

WLAN/4/AP_OPTICAL_TEMPERATURE_TOO_HIGH:OID [oid] AP optical module temperature is too high notify. (APMAC=[MacAddress], APName=[STRING], ApIfIndex=[INTEGER], Ap Optical Temperature=[INTEGER]°C, ApEntityPhysicalName=[OCTET], APID=[INTEGER])

The temperature of AP's optical module is higher than the upper temperature alarm threshold.

WLAN/4/AP_OPTICAL_TEMPERATURE_TOO_HIGH_RESTORE:OID [oid] The temperature of the AP's optical module falls below the upper threshold. (APMAC=[MacAddress], APName=[STRING], ApIfIndex=[INTEGER], Ap Optical Temperature=[INTEGER]°C, ApEntityPhysicalName=[OCTET], APID=[INTEGER])

The temperature of the AP's optical module has fallen below the upper temperature alarm threshold.

WLAN/4/AP_OPTICAL_TEMPERATURE_TOO_LOW:OID [oid] AP optical module temperature is too low notify. (APMAC=[MacAddress], APName=[STRING], ApIfIndex=[INTEGER], Ap Optical Temperature=[INTEGER]°C, ApEntityPhysicalName=[OCTET], APID=[INTEGER])

The temperature of AP's optical module is lower than the lower temperature alarm threshold.

WLAN/4/AP_OPTICAL_TEMPERATURE_TOO_LOW_RESTORE:OID [oid] The temperature of the AP's optical module increases above the lower threshold. (APMAC=[MacAddress], APName=[STRING], ApIfIndex=[INTEGER], Ap Optical Temperature=[INTEGER]°C, ApEntityPhysicalName=[OCTET], APID=[INTEGER])

The temperature of AP's optical module has increased above the lower temperature alarm threshold.

WLAN/4/AP_UNSUPPORT_COUNTRY_CODE:OID [oid] AP not support configured country code notify.(APMAC=[MacAddress], APName=[STRING], COUNTRY CODE=[OCTET], APID=[INTEGER])

The AP does not support the country code configured on the device.

WLAN/4/AP_COLD_BOOT:OID [oid] The AP cold boot. (APMAC=[MacAddress], AP TYPE=[OCTET], AP Sys Name=[OCTET], AP Sys Time=[OCTET], AP Alarm name=[OCTET], APID=[INTEGER])

The AP was cold started. After the AP was disconnected because of power-off, it connected to the AC again and operated properly.

WLAN/4/AP_COLD_BOOT_RESTORE:OID [oid] The AP cold boot restore. (APMAC=[MacAddress], AP TYPE=[OCTET], AP Sys Name=[OCTET], AP Sys Time=[OCTET], AP Alarm name=[OCTET], APID=[INTEGER])

The AP restored after a cold restart. After the AP was disconnected because of power-off, it connected to the AC again and operated properly.

WLAN/4/AP_HOT_BOOT:OID [oid] AP hot boot. (APMAC=[OPAQUE], APType=[OCTET], APName=[OCTET], APOccurTime=[OCTET], NotifyName=[OCTET], APID=[INTEGER])

An AP is hot started.

WLAN/4/AP_HOT_BOOT_RESTORE:OID [oid] AP hot boot restore. (APMAC=[OPAQUE], APType=[OCTET], APName=[OCTET], APOccurTime=[OCTET], NotifyName=[OCTET], APID=[INTEGER])

The AP is restored after a hot restart. An alarm is generated after an AP is manually restarted, and goes online and operates properly.

WLAN/4/AP_CRC_TOO_HIGH:OID [oid] AP CRC is abnormal notify. (APMAC=[OPAQUE], APName=[STRING], APCrcErrRate=[LONG]/10000, PortType=[OCTET], PortID=[INTEGER], APID=[INTEGER])

The number of CRC error packets collected at a specified sampling interval exceeded the threshold.

WLAN/4/AP_CRC_TOO_HIGH_RESTORE:OID [oid] The number of the AP's CRC errors changes to normal.(APMAC=[OPAQUE], APName=[STRING], APCrcErrRate=[LONG]/10000, PortType=[OCTET], PortID=[INTEGER], APID=[INTEGER])

The number of CRC error packets collected at a specified sampling interval fell below the alarm threshold.

WLAN/4/AP_NAME_CONFLICT:OID [oid] Report ap name conflict. (APMAC=[OPAQUE], APReportName=[OCTET], APOccurTime=[OCTET], APID=[INTEGER])

The name of a new online AP reported to the AC conflicts with that of an existing online AP.

WLAN/4/AP_NUM_REACH_LICENSE_UPLIMIT:OID [oid] AP License Notify. (Info = [OCTET])

AP specific license resources were insufficient (the number of online APs reached the maximum).

WLAN/4/AP_FMEA_FAULT_IIC_CHANNEL:OID [oid] AP IIC channel fault. (AP MAC=[OPAQUE], APName=[STRING], APID=[INTEGER])

The AP's IIC channel fails.

WLAN/4/AP_FMEA_FAULT_IIC_CHANNEL_RESTORE:OID [oid] AP IIC channel fault clear. (APMAC=[OPAQUE], APName=[STRING], APID=[INTEGER])

The AP's IIC channel fault is rectified.

WLAN/4/AP_FMEA_FAULT_PHY_CMOS:OID [oid] AP PHY CMOS fault. (APMAC=[OPAQUE], APName=[STRING], APID=[INTEGER])

The AP's PHY chip fails.

WLAN/4/AP_FMEA_FAULT_PHY_CMOS_RESTORE:OID [oid] AP PHY CMOS fault clear. (APMAC=[OPAQUE], APName=[STRING], APID=[INTEGER])

The AP's PHY chip fault is rectified.

WLAN/2/AP_FMEA_FAULT:OID [oid] AP FMEA fault. (APMAC=[OPAQUE], APName=[STRING], FaultID=[INTEGER], Index=[INTEGER], FaultInfo=[STRING], APID=[INTEGER])

The AP generates an alarm when a hardware fault occurs.

If a device generates a Failure Mode Effect Analysis (FMEA) alarm, the hardware circuit, module, or chip of the device becomes faulty.

WLAN/4/AP_FMEA_FAULT_RESTORE:OID [oid] AP FMEA fault clear. (APMAC=[OPAQUE], APName=[STRING], FaultID=[INTEGER], Index=[INTEGER], FaultInfo=[STRING], APID=[INTEGER])

The AP generates a clear alarm when a hardware fault is rectified.

WLAN/4/AP_OPTICAL_INSERT:OID [oid] AP optical insert. (APMAC=[OPAQUE], APName=[STRING], IfIndex=[INTEGER], ApEntityPhysicalName=[OCTET], APID=[INTEGER])

An alarm is generated when an optical module is installed on an AP.

WLAN/4/AP_OPTICAL_REMOVE:OID [oid] AP optical remove. (APMAC=[OPAQUE], APName=[STRING], IfIndex=[INTEGER], ApEntityPhysicalName=[OCTET], APID=[INTEGER])

An alarm is generated when an optical module is removed from an AP.

WLAN/4/AP_RECEIVED_INVALID_ARP_PACKET:OID [oid] AP received invalid arp packet notify.(APMAC=[OPAQUE], APName=[STRING], RadioID=[INTEGER], WlanID=[INTEGER], Drop Num=[INTEGER], APID=[INTEGER])

The AP receives invalid ARP packets.

WLAN/4/AP_SOFTWARE_VERSION_MISMATCH:OID [oid] AP software version is not match with AC software version.(APMAC=[OPAQUE], APName=[STRING], APType=[OCTET], APSoftWareVersion=[OCTET], APID=[INTEGER])

The AP's version does not match the AC's.

WLAN/4/RADIO_UPLOAD_REMOTE_CAPTURE_FILE_RESULT:OID [oid] Upload remote capture file notify. (APMAC=[OPAQUE], APName=[STRING], RadioID=[INTEGER], Info = [OCTET], APID=[INTEGER])

This alarm describes upload results of remote packet capturing files.

WLAN/4/MP_JOINED_ON_ETHERNET:OID [oid] MP reached AC through the Ethernet port,and this MP doesn't setup mesh link in avoid of loopback.(APMAC=[OPAQUE], APName=[STRING], APID=[INTEGER])

An MP goes online through an Ethernet interface.

WLAN/4/MP_JOINED_ON_ETHERNET_RESTORE: OID [oid] MP reached AC through the air,and this MP has reported 'MP joined AC through Ethernet port'warning,so restore it. (APMAC=[OPAQUE], APName=[STRING], APID=[INTEGER])

An MP that went online through an Ethernet interface goes online through an air interface.

WLAN/4/MPP_JOINED_ON_AIR:OID [oid] MPP can't reach AC through the Ethernet port,so this MPP joins AC through the air,changes itself to MP,and forbid traffic on the Ethernet port in avoid of loopback. (APMAC=[OPAQUE], APName=[STRING], APID=[INTEGER])

An MPP changes to an MP and goes online through an air interface.

WLAN/4/MPP_JOINED_ON_AIR_RESTORE: OID [oid] MPP reached AC through the Ethernet port,and this MP has reported 'MPP joined AC through air'warning,so restore it. (APMAC=[OPAQUE], APName=[STRING], APID=[INTEGER])

An MPP that went online through an air interface goes online through an Ethernet interface.

WLAN/4/AP_OPTICAL_TX_POWER_TOO_HIGH:OID [oid] AP optical module transfer power is too high notify. (APMAC=[OPAQUE], APName=[STRING], ApIfIndex=[INTEGER], Ap Optical TxPower=[INTEGER](0.1uw), ApEntityPhysicalName=[OCTET], APID=[INTEGER])

The transmit power of the AP's optical module exceeded the upper threshold.