Example for Configuring MAD in Direct Mode

Procedure

1. Configure MAD in direct mode on a specified port.

   # Configure MAD in direct mode on GigabitEthernet0/0/5.

   <HUAWEI> system-view
   [HUAWEI] interface gigabitethernet 0/0/5
   [HUAWEI-GigabitEthernet0/0/5] mad detect mode direct
   Warning: This command will block the port, and no other configuration running on this port is recommended. Continue?[Y/N]:y 
   [HUAWEI-GigabitEthernet0/0/5] quit
   [HUAWEI] quit

   # Configure MAD in direct mode on GigabitEthernet1/0/5.

   <HUAWEI> system-view
   [HUAWEI] interface gigabitethernet 1/0/5
   [HUAWEI-GigabitEthernet1/0/5] mad detect mode direct
   Warning: This command will block the port, and no other configuration running on this port is recommended. Continue?[Y/N]:y 
   [HUAWEI-GigabitEthernet1/0/5] quit
   [HUAWEI] quit

2. Verify the configuration.

   # Check detailed MAD configuration of the stack.

   <HUAWEI> display mad verbose
   Current MAD domain: 0 
   Current MAD status: Detect                                                      
   Mad direct detect interfaces configured:                                
    GigabitEthernet0/0/5
    GigabitEthernet1/0/5                                                          
   Mad relay detect interfaces configured:                                 
   Excluded ports(configurable):                                                   
   Excluded ports(can not be configured):
    GigabitEthernet0/0/27
    GigabitEthernet1/0/27
   

3. Verify the MAD function.
   After the MAD function has been configured successfully:

   • The system can generate an alarm of MAD_1.3.6.1.4.1.2011.5.25.246.1.1 hwMadConflictDetect if the stack splits.
   • When the stack recovers, the system generates an alarm of MAD_1.3.6.1.4.1.2011.5.25.246.1.2 hwMadConflictResume.

   If no service is configured in the stack, perform the following steps to check whether the MAD function has been configured successfully:

   1. Enable the alarm display function in the user view.

      <HUAWEI> terminal monitor
      <HUAWEI> terminal trapping

   2. Simulate a stack split situation by removing some stack cables. If the stack is set up through service port connections, you can also run the shutdown interface command to shut down some physical member ports in the logical stack port view.
   3. After the stack splits, you can see the following alarm on the terminal: MAD/4/MULTIACTIVEDETECTED:OID 1.3.6.1.4.1.2011.5.25.246.1.1 Multi-active scenario is detected.
   4. Check whether the number of member switches decreases.

      Run the display device command, and you can see that the number of member switches decreases from 2 to 1. (In this example, the member switches are S5720-28P-LI-AC.)

      <HUAWEI> display device
      S5720-28P-LI-AC's Device status:
      Slot Sub  Type                Online    Power      Register     Status   Role
      - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
      0    -   S5720-28P-LI         Present   PowerOn    Registered   Normal   Master

   5. The preceding operations verify that the MAD function has been configured successfully.
   6. Connect the stack cables again or run the undo shutdown command to enable the physical member ports, so that the stack can be set up again.
   7. After the stack is set up again, you can see the following alarm on the terminal: MAD/4/MULTIACTIVEMERGE:OID 1.3.6.1.4.1.2011.5.25.246.1.2 Multi-active scenario is merged.
   8. Check whether the number of member switches restores to the original value.

      Run the display device command, and you can see that the number of member switches changes to 2. (In this example, the member switches are S5720-28P-LI-AC.)

      <HUAWEI> display device
      S5720-28P-LI-AC's Device status:
      Slot Sub  Type                Online    Power      Register     Status   Role
      - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
      0    -   S5720-28P-LI         Present   PowerOn    Registered   Normal   Master
      1    -   S5720-28P-LI         Present   PowerOn    Registered   Normal   Standby