Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document.
Note: Even the most advanced machine translation cannot match the quality of professional translators.
Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Help
The iBMC CLI provides information about how to use the commands. To obtain help information, enter part of a command and press Enter.
Examples:
Query command:
iBMC:/->ipmcget Usage: ipmcget [-t target] -d dataitem [-v value] -t <target> fru0 Get the information of the fru0 sensor Print detailed sensor information smbios Get the information of smbios trap Get SNMP trap status service Get service information maintenance Get maintenance information syslog Get syslog status user Get the information of user securitybanner Get login security banner information vnc Get VNC information storage Get storage device information config Get configuration information vmm Get Virtual Media information certificate Get SSL certificate information sol Get SOL information securityenhance Get security enhance information -d <dataitem> faninfo Get fan mode and the percentage of the fan speed port80 Get the diagnose code of port 80 diaginfo Get diagnostic info of management subsystem systemcom Get system com data blackbox Get black box data bootdevice Get boot device shutdowntimeout Get graceful shutdown timeout state and value powerstate Get power state health Get health status healthevents Get health events sel Print System Event Log (SEL) operatelog Print operation log version Get iBMC version serialnumber Get system serial number userlist List all user info fruinfo Get fru information time Get system time macaddr Get mac address serialdir Get currently connected serial direction rollbackstatus Get rollback status passwordcomplexity Get password complexity check enable status ledinfo Get led information ipinfo Get ip information ethport Get usable eth port psuinfo Get PSU component information autodiscovery Get autodiscovery configuration poweronpermit Get poweronpermit configuration minimumpasswordage Get minimum password age configuration ntpinfo Get NTP information npuworkmode Get NPU work mode leakagestrategy Get power-off strategy after leakage
Set command:
iBMC:/->ipmcset Usage: ipmcset [-t target] -d dataitem [-v value] -t <target> fru0 Operate with fru0 trap Operate SNMP trap service Operate with service user Operate with user maintenance Operate with maintenance sensor Operate with sensor securitybanner Operate login security banner information syslog Operate syslog ntp Operate ntp vnc Operate vnc storage Configure storage device config Operate configuration vmm Operate virtual media certificate Operate certificate sol Operate SOL securityenhance Operate security enhance precisealarm Operate with precise alarm -d <dataitem> fanmode Set fan mode,you can choose manual or auto fanlevel Set fan speed percent reset Reboot iBMC system identify Operate identify led upgrade Upgrade component clearcmos Clear CMOS bootdevice Set boot device shutdowntimeout Set graceful shutdown timeout state and value frucontrol Fru control powerstate Set power state sel Clear SEL adduser Add user password Modify user password deluser Delete user privilege Set user privilege npuworkmode Set NPU work mode serialdir Set serial direction printscreen Print current screen to iBMC rollback Perform a manual rollback timezone Set time zone passwordcomplexity Set password complexity check enable state ipaddr Set ip address backupipaddr Set backup ip address ipmode Set ip mode gateway Set gateway ipaddr6 Set ipv6 address ipmode6 Set ipv6 mode gateway6 Set ipv6 gateway netmode Set net mode activeport Set EthGroup active port vlan Set sideband vlan restore Restore factory setting notimeout Set no timeout state emergencyuser Set emergency user autodiscovery Set autodiscovery configuration poweronpermit Set poweronpermit configuration minimumpasswordage Set minimum password age configuration crl Upload CRL file psuworkmode Set PSU work mode fpgagoldenfwrestore FPGA golden firmware restore leakagestrategy Set power-off strategy after leakage
If an incorrect parameter is entered, the help information prompts the correct optional parameters.
The following is an example:
iBMC:/->ipmcset -d inff Usage: ipmcset [-t target] -d dataitem [-v value] -t <target> fru0 Operate with fru0 trap Operate SNMP trap service Operate with service user Operate with user maintenance Operate with maintenance sensor Operate with sensor securitybanner Operate login security banner information syslog Operate syslog ntp Operate ntp vnc Operate vnc storage Configure storage device config Operate configuration vmm Operate virtual media certificate Operate certificate sol Operate SOL securityenhance Operate security enhance precisealarm Operate with precise alarm -d <dataitem> fanmode Set fan mode,you can choose manual or auto fanlevel Set fan speed percent reset Reboot iBMC system identify Operate identify led upgrade Upgrade component clearcmos Clear CMOS bootdevice Set boot device shutdowntimeout Set graceful shutdown timeout state and value frucontrol Fru control powerstate Set power state sel Clear SEL adduser Add user password Modify user password deluser Delete user privilege Set user privilege npuworkmode Set NPU work mode serialdir Set serial direction printscreen Print current screen to iBMC rollback Perform a manual rollback timezone Set time zone passwordcomplexity Set password complexity check enable state ipaddr Set ip address backupipaddr Set backup ip address ipmode Set ip mode gateway Set gateway ipaddr6 Set ipv6 address ipmode6 Set ipv6 mode gateway6 Set ipv6 gateway netmode Set net mode activeport Set EthGroup active port vlan Set sideband vlan restore Restore factory setting notimeout Set no timeout state emergencyuser Set emergency user autodiscovery Set autodiscovery configuration poweronpermit Set poweronpermit configuration minimumpasswordage Set minimum password age configuration crl Upload CRL file psuworkmode Set PSU work mode fpgagoldenfwrestore FPGA golden firmware restore leakagestrategy Set power-off strategy after leakage