No relevant resource is found in the selected language.
MENU
Support Documentation
Wireless Access Controller (AC and Fit AP) V200R019C10 Web-based Configuration Guide
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Example for Configuring an AC and APs to Report KPI Information

Example for Configuring an AC and APs to Report KPI Information

Service Requirements

In the cloud managed AC + Fit AP networking, KPI information of an AC and APs is reported to iMaster NCE-Campus and CampusInsight through the WMI report mechanism.

Networking Requirements

Some models of APs directly report KPI information, while other models of APs transparently report KPI information through an AC. Figure 3-88 and Figure 3-89 show the two KPI information report modes.

Figure 3-88 Direct KPI information report
Figure 3-89 Transparent KPI information report through an AC

Data Planning

Item

Data

AP group

ap-group1

AP system profile

default

KPI information reported by the AC
  • The AC reports the following KPI information to iMaster NCE-Campus:
    • Destination IP address: 10.1.2.3
    • Port number: 10032
  • The AC reports the following KPI information to CampusInsight:
    • Destination IP address: 10.2.3.4
    • Port number: 27371

KPI information reported by an AP
  • The AP reports the following KPI information to iMaster NCE-Campus:
    • WMI profile name: cloudmng
    • Destination IP address: 10.1.2.3
    • Port number: 10032
  • The AP reports the following KPI information to CampusInsight:
    • WMI profile name: campusinsight
    • Destination IP address: 10.2.3.4
    • Port number: 27371

Configuration Roadmap

  1. Configure basic WLAN services so that APs can go online.
  2. Configure parameters for interconnecting the AC with the WMI server.
  3. Configure parameters for interconnecting APs with the WMI server using the WMI profile and bind WMI profile to the AP group using the AP system profile.

Configuration Notes

  • KPI information to be reported by an AP depends on the AP model. For details, see Licensing Requirements and Limitations for KPI Information Report in CLI-based Configuration Guide.
    • For an AP that directly reports KPI information, if KPI information of the AC does not need to be reported, you can omit the step of configuring parameters for interconnecting the AC with the WMI server.
    • For an AP that transparently reports KPI information through an AC, you must configure parameters for interconnecting the AC with the WMI server.
  • If the KPI information needs to be reported to only one WMI server, do not configure multiple information report channels to avoid resource waste of the target server.
  • To ensure that KPI information can be successfully reported, pre-configure network connectivity to make the AC and APs properly communicate with the WMI server.

Procedure

  1. Configure basic WLAN services to make APs go online. The AP group name is ap-group1.
  2. Configure parameters for interconnecting the AC with the WMI server.
    1. Configure parameters for interconnecting the AC with iMaster NCE-Campus.

      Choose Maintenance > AC Maintenance > WMI from the main menu on the AC web NMS, configure parameters for interconnecting the AC with iMaster NCE-Campus on the Channel 1 tab page, and click Apply.

      Typically, the port number of iMaster NCE-Campus is 10032.

    2. Configure parameters for interconnecting the AC with CampusInsight.

      Choose Maintenance > AC Maintenance > WMI from the main menu on the AC web NMS, configure parameters for interconnecting the AC with CampusInsight on the Channel 2 tab page, and click Apply.

      Typically, the port number of CampusInsight is 27371.

  3. Configure parameters for interconnecting APs with the WMI server.
    1. Configure parameters for interconnecting APs with iMaster NCE-Campus.

      # Choose Configuration > AP Config > AP Group from the main menu on the AC web NMS, and click ap-group1 on the AP Group tab page.

      # Choose AP > AP System Profile > WMI Profile (Channel 1) and click Create to create the WMI profile cloudmng.

      # Configure parameters for interconnecting APs with iMaster NCE-Campus according to the data plan and click Apply.

    2. Configure parameters for interconnecting APs with CampusInsight.

      # Choose Configuration > AP Config > AP Group from the main menu on the AC web NMS, and click ap-group1 on the AP Group tab page.

      # Choose AP > AP System Profile > WMI Profile (Channel 2) and click Create to create the WMI profile campusinsight.

      # Configure parameters for interconnecting APs with CampusInsight according to the data plan and click Apply.

Translation
简体中文
Download
Updated: 2020-09-07

Document ID: EDOC1100156625

Views: 5347

Downloads: 505

Average rating:
This Document Applies to these Products

Related Version

Related Documents

Share
Previous Next
Enterprise APP

Copyright © 2021 Huawei Technologies Co., Ltd. All rights reserved.

You are going to visit :