Mounting Table Legs and Connecting Frames

Background

The multi-functional conference table in the second row consists of table legs, connecting frames, and tabletops. Before installing the multi-functional conference table, understand the following information:

• Table legs

The multi-functional conference table in the second row has a total of seven legs. The five legs in the middle are insensitive to left and right, while the two legs on both sides are sensitive. You can distinguish the table legs to be installed on the left and right based on their labels. Figure 8-4 shows the appearance of the table legs to be installed on the left, in the middle, and on the right respectively.

Figure 8-4 Labels on the table legs

Among the labels on the table legs, "LEFT"/"RIGHT" indicates the table leg to be installed on the left/right, and "TV" indicates the direction in which the display is installed.

• Connecting frames

The second-row multi-functional conference table has six connecting frames (E1, E2, E3, E5, E6, and E7) and one connecting piece (E4). Install the connecting pieces based on their labels.

Tear off the protective film from the table legs. To prevent damage to the table legs, do not use any sharp-edged tools for the tear-off.

Procedure

1. Install the five table legs in the middle.
   1. Install the table leg at the very center.

      Place the table leg towards the display as instructed by the label, and insert it into the groove on the horizontal fixture board, as shown in Figure 8-5.

      Figure 8-5 Installing the table leg at the very center
      
   2. Install the two legs to the left and right of the table leg at the very center in the same way, as shown in Figure 8-6.
      Figure 8-6 Installing the two legs to the left and right of the table leg at the very center
      
   3. Install the two table legs at the leftmost and rightmost ends in the same way, as shown in Figure 8-7.
      Figure 8-7 Installing the leftmost and rightmost table legs
      

2. Install the connecting piece (E4) on the table leg at the very center.
   1. Insert the connecting piece E4 into the table leg at the very center, as shown by in Figure 8-9.
   2. Tighten five M6 x 16 hex socket screws to fix the connecting piece, as shown by in Figure 8-8.
      Figure 8-8 Installing the connecting piece E4 on the table leg at the very center
      
   3. Install the 6-outlet PDU fixing support and tighten four M6 x 16 hex socket screws, as shown in Figure 8-9.
      Figure 8-9 Installing the 6-outlet PDU fixing support
      

3. Installing the connecting frames E2, E3, E5, and E6
   1. Insert one end of the connecting frame E5 into the table leg on the right, as shown by in Figure 8-10.
   2. Insert the other end of the connecting frame E5 into the connecting piece E4, as shown by in Figure 8-10.
   3. Tighten fourteen M6 x 16 hex socket screws to fix the table leg connecting frame (E5).
      Figure 8-10 Installing the connecting frame E5
      
   4. Install the connecting frames E2, E3, and E6 in the same way as installing the connecting frame E5. Figure 8-11 shows the effect after installation.
      Figure 8-11 Installing the connecting frames E2, E3, and E6
      

4. Install the connecting frames E1 and E7.
   1. Insert the connecting frame E7 into the groove of the connecting frame E6, as shown by in Figure 8-12.
   2. Tighten five M6 x 16 hex socket screws to fix the connecting frame E7, as shown by in Figure 8-12.
      Figure 8-12 Installing the connecting frame E7
      
   3. Install the table leg connecting frame E1 in the same way as installing the connecting frame E7. Figure 8-13 shows the effect after installation.
      Figure 8-13 Connecting frame E1 installed
      

5. Install the left and right table legs.
   1. Distinguish the left and right table legs according to their labels, and place the legs towards the display.
   2. Insert the left table leg into the groove of the connecting frame E1, as shown by in Figure 8-14.
   3. Tighten five M6 x 16 hex socket screws to fix the left table leg, as shown by in Figure 8-14.
      Figure 8-14 Installing the left table leg
      
   4. Install the right table leg in the same way as the left table leg, as shown in Figure 8-15.
      Figure 8-15 The right table leg installed
      

6. Check whether all table legs and connecting frames are fixed.
7. Remove the fixture board, as shown in Figure 8-16.
   Figure 8-16 The fixture board removed