No relevant resource is found in the selected language.
Enterprise
Worldwide
Search
Support Documentation
FusionModule500 Smart Mini Data Center User Manual (Philippines, Integrated Air Conditioner)
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Commissioning Sensors

Commissioning Sensors

Setting and Adding a Smoke Detector (Connected to an AI/DI Port on the ECC800-Pro)

If a smoke detector is installed, perform the following steps to configure it.

Context

If the detector is prefabricated, only check its settings.

Procedure

  1. Set smoke detector parameters.
    1. Log in to the ECC800-Pro WebUI as an administrator.
    2. Choose System Settings > Signal Name Modify. The Batch Signal Configuration tab page is displayed.
    3. Set Device type to ECC800, set Device name to ECC800, and click OK.
    4. On the query result tab page, set the new signal name of AI/DI_1 to Smoke and click Submit.
    5. Choose Monitoring > System > ECC800 > Running Parameters > AI/DI_1 Port Settings.
    6. Set Smoke sensor to Enable and click Submit.
  2. Check the monitoring functions of smoke detector.

    Table 5-7 Commissioning the detector

    Check Method

    Normal Connection Status

    Alarm Clearance Method

    Simulate a smoky environment under the smoke detector.

    Smoke DI alarm is displayed on the active alarm page of the app or WebUI.

    Disconnect the smoke detector cable and then reconnect it to clear the alarm.

Commissioning a T/H Sensor

Prerequisites

One end of the straight-through cable has been connected to the RS485_IN port on the T/H sensor, and the other end has been connected to the COM port on the ECC800-Pro.

Procedure

  1. Set a device address for the T/H sensor.

    Operate the DIP switch on the T/H sensor to set the device address for the sensor.

    Toggle switches 1 to 6 specify the device address in binary mode. ON indicates 1, and OFF indicates 0.

    Figure 5-6 DIP switch definitions for T/H sensors

    Numbers 1 and 2 indicate the DIP switch settings of T/H sensors. The DIP switch of the T/H sensor on the front door is set to 2, and that of the T/H sensor on the rear door is set to 1.

    Table 5-8 Setting device addresses

    Address

    Toggle Switch 1

    Toggle Switch 2

    Toggle Switch 3

    Toggle Switch 4

    Toggle Switch 5

    Toggle Switch 6

    1

    ON

    OFF

    OFF

    OFF

    OFF

    OFF

    2

    OFF

    ON

    OFF

    OFF

    OFF

    OFF

  2. Add a T/H sensor.
    1. Log in to the ECC800-Pro WebUI as an administrator.
    2. Add a T/H sensor.

      Table 5-9 Adding a T/H sensor

      Path

      Parameter

      Setting

      Choose System Settings > Device Management and click Add Device.

      Device Attribute

      Select Sensor from the drop-down list box.

      Device Type

      Select T/H sensor from the drop-down list box.

      Connect To

      Select ECC800 from the drop-down list box.

      Communications Port

      Select COM1 from the drop-down list box.

      Device Address

      In this example, device address is set to 1. During actual configuration, set the device address for the T/H sensor based on the actual situation.

    3. Click Test Connect to check whether the T/H sensor connects to the ECC800-Pro properly.

      • If the connection is normal, click Confirm. The connected devices are displayed in the Number of connected devices list.
      • If the connection is abnormal, check whether the device is properly connected to the ECC800-Pro, whether the device and the ECC800-Pro are running properly, and whether the parameter settings are consistent with the device parameters.

  3. Check the function of the T/H sensor.

    Table 5-10 Function check

    Check Method

    Normal Connection Status

    Check the running information about the T/H sensor on the WebUI.

    Choose Monitoring > Aisle > T/H Sensor Group > T/H Sensor n > Running Info, and view the current cabinet temperature and humidity.

    Set T/H sensor alarm thresholds.

    Choose Monitoring > Aisle > T/H Sensor Group > T/H Sensor n > Running Parameters and set High temperature alarm threshold, Low temperature alarm threshold, High humidity alarm threshold, and Low humidity alarm threshold as required.

    NOTE:

    The default values of High temperature alarm threshold, Low temperature alarm threshold, High humidity alarm threshold, and Low humidity alarm threshold for the cold aisle are 35.0°C, 5.0°C, 85.0% RH, and 15.0% RH respectively. The default values of High temperature alarm threshold, Low temperature alarm threshold, High humidity alarm threshold, and Low humidity alarm threshold for the hot aisle are 45.0°C, 10.0°C, 85.0% RH, and 15.0% RH, respectively. The cold and hot aisles can be determined based on the DIP switch settings of the T/H sensors.

Commissioning the Electrode Water Sensor

Prerequisites

One end of the network cable has been stripped, core wires 7 and 8 have been connected to the cable delivered with the electrode water sensor, and the other end of the network cable has been connected to the AI/DI port on the rack environment unit.

Context

  • To use the AI/DI sensor, enable the corresponding AI/DI port and name the sensor. The specific alarm then can be reported.
  • If the sensor is prefabricated, only check its settings.
  • The actual value may vary. Only the method of the parameter settings is described.

Procedure

  1. Set water sensor parameters.

    The following describes how to connect a water sensor to the AI/DI_2 port on the ECC800-Pro.

    1. Log in to the ECC800-Pro WebUI as an administrator.
    2. Choose System Settings > Signal Name Modify. The Batch Signal Configuration page is displayed.
    3. Set Device type to ECC800, set Device name to ECC800, and click OK.
    4. On the query result tab page, set the new signal name of AI/DI_2 to Leak and click Submit.
    5. Choose Monitoring > System > ECC800 > Running Parameters > AI/DI_2 Port Settings.
    6. Set Leak sensor to Enable and click Submit.
    7. Set Leak sensor type to Leak sensor(Electroc) and click Submit.
    8. Click Unhide All Advanced Signals, and click Power Supply Parameters. Ensure that I power supply enable(AIDI_2/COM1/AIDI_4/COM3) is Enable.
  2. Check functions of water sensors.

    Table 5-11 Function check

    Check Method

    Normal Connection Status

    Alarm Clearance Method

    Immerse the two contacts of the electrode water sensor in water.

    Leak DI alarm is generated on the active alarm screen of the app or on the WebUI.

    Wipe dry the two contacts of the water sensor. The alarm disappears automatically.

Translation
简体中文
Download
Updated: 2021-07-14

Document ID: EDOC1100165911

Views: 9408

Downloads: 404

Average rating:
This Document Applies to these Products

Related Version

Related Documents

Digital Signature File

Digital Signature Authentication Mode
Share
Previous Next

Copyright © 2023 Huawei Technologies Co., Ltd. All rights reserved.

You are going to visit :