Commissioning a Cabinet Electronic Clasp Lock

Procedure

1. (Optional) Check whether the cabinet door lock is leveled to 2000 (+3) mm. If not, adjust it.
2. (Optional) If the cabinet door still cannot be opened after step 1 is performed, adjust the position of the cabinet electronic clasp lock by using the slotted holes until the cabinet door can be opened and closed properly.
3. Set device addresses for cabinet electronic clasp locks.
   • A cabinet electronic clasp lock is installed at the front and rear doors of the cabinet respectively. The address for the cabinet electronic clasp lock on the front door is an odd number, and that for the cabinet electronic clasp lock on the rear door is an even number.
   • Set a device address for a cabinet electronic clasp lock by operating the toggle switch on the cabinet electronic clasp lock. Toggle switches 1 to 6 specify the device address in binary mode. ON indicates 1, and OFF indicates 0.
   Figure 5-7 Toggle switch addresses of the cabinet electronic locks
   

   The number indicates the DIP switch setting of the electronic clasp lock.

   Table 5-12 Setting device addresses

   Address	Toggle Switch 1	Toggle Switch 2	Toggle Switch 3	Toggle Switch 4	Toggle Switch 5	Toggle Switch 6
   1	ON	OFF	OFF	OFF	OFF	OFF
   2	OFF	ON	OFF	OFF	OFF	OFF

4. Add the cabinet electronic clasp locks.
   1. Log in to the ECC800-Pro WebUI as an administrator.
   2. Create a cabinet view in Smart Module View on the home page.
   3. Add a cabinet electronic clasp lock.
      Table 5-13 Adding a cabinet electronic clasp lock

      Path	Parameter	Setting
      Choose System Settings > Device Management and click Add Device.	Device Attribute	Cabinet Electronic Clasp Lock
      	Device Type	Cabinet Electronic Clasp Lock
      	Connect To	ECC800-Pro
      	Communications Port	COM2
      	Device Address	Enter the actual device address of the cabinet electronic clasp lock.

   4. Click Test Connect to check whether the connection between the cabinet electronic clasp lock and the ECC800-Pro is normal.
      • If the connection is normal, click Confirm. The connected devices are displayed in the Number of connected devices list.
      • If the connection is abnormal, check whether the device is properly connected to the ECC800-Pro, whether the device and the ECC800-Pro are running properly, and whether the parameter settings are consistent with the device parameters.

   5. Repeat Step 4.3 and Step 4.4 to connect other cabinet electronic clasp locks.
5. Commission the cabinet electronic clasp locks.
   Table 5-14 Function check

   Function	Path		Operation
   View cabinet electronic clasp lock information	Choose Monitoring > Cabinet > Global cabinet > Cabinet Electronic Clasp Lockn.	Click the Running Info tab.	View the running information about cabinet electronic clasp lock 1 on the WebUI.
   Change the cabinet electronic clasp lock name.		Click the Running Parameters tab.	Change the cabinet electronic clasp lock name.
   Remotely open a cabinet electronic clasp lock		Click the Controls tab.	Select Open the door on Controls, and click Submit to remotely open the door.
   Open cabinet electronic clasp locks in batches	Choose Monitoring > Cabinet and click the Controls tab.		Select Open front door or Open back door from the Open the door drop-down list box, select the setting, and click Submit. The cabinet electronic clasp locks unlock the doors in batches based on the signal value.
   a: Cabinet electronic clasp lock 1 is used as an example.

6. When closing the door, rotate the lock handle vertically downward. If the door cannot be opened or closed properly, locate the fault.
   1. Check whether there is friction between the lock tongue and the cabinet electronic clasp lock. If so, adjust the installation position of the clasp lock.
      Figure 5-8 Adjusting the position of a clasp lock
      
   2. Check whether there is interference between the lock tongue and the cabinet column. If so, adjust the installation position of the lock tongue.
      Figure 5-9 Adjusting the position of a lock tongue
      
   3. Check whether there is interference between the castors and the door sill at the bottom of the cabinet. If so, remove the fasteners that secure the castors.
      Figure 5-10 Removing the fastener
      

   If the door still cannot be opened or closed properly, check the following items:

   • Whether cables are connected correctly
   • Whether the DIP switch setting is correct