No relevant resource is found in the selected language.
Enterprise
Worldwide
Search
Support Documentation
FusionModule500 Smart Mini Data Center User Manual (Philippines, Integrated Air Conditioner)
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
(Optional) NetEco Management

(Optional) NetEco Management

Data Center Management

Connecting a Communications Cable

Procedure

  1. Connect a communications cable to the WAN1 port on the ECC800-Pro.

    Figure 5-16 Connecting a communications cable

Setting NetEco Parameters

Procedure

  1. Apply for a fixed IP address to the equipment room network administrator.
  2. Set the IP address, subnet mask, and default gateway on the ECC800-Pro WebUI.

    Table 5-18 IP parameters

    Path

    Parameter

    Default Value

    Setting

    System Settings > System Parameters > Monitor IP > WAN_1

    IP

    192.168.8.10

    Set this parameter based on the IP address assigned by the network administrator.

    Subnet mask

    255.255.255.0

    Set this parameter based on the subnet mask assigned by the network administrator.

    Default gateway

    192.168.8.1

    Set this parameter based on the default gateway address assigned by the network administrator.

  3. Click Submit.
  4. Set NetEco communications parameters and authentication password on the ECC800-Pro WebUI.

    Table 5-19 NetEco parameters

    Path

    Parameter

    Default Value

    Setting

    System Settings > NMS Application > NetEco > Communication Parameters

    Server IP

    192.168.8.11

    IP address of the primary NetEco server

    NOTE:

    The NetEco IP address and the ECC800-Pro IP address must be configured in the same network to ensure normal connection between the NetEco and the ECC800-Pro.

    Port number

    31220

    31220

    Network port for link setup

    WAN_1

    WAN_1
    Table 5-20 Setting an authentication password

    Path

    Parameter

    Default Value

    Setting

    System Settings > NMS Application > NetEco > Set Authentication Password

    Authentication password

    Modifyme_123

    Set this parameter based on customer requirements.

    NOTE:

    Requirements for setting passwords:

    'a~z','A~Z','0~9','~!@#^*_={}:,./?-`$'(8-32 characters that include at least three of the following types: lowercase letters, uppercase letters, digits, and special characters)

    Confirm authentication password

    -

    -

  5. Click Submit.

Powering On a Server

This topic describes how to power on a server.

Procedure

  1. Check that the power cables and ground cables of the upstream components of the server are securely connected with correct polarity and in good contact.
  2. Ensure that the upstream input power supply is not connected. Use a multimeter to measure the resistance between the upstream output power supplies and between the working ground and the protection ground. It is required that short circuit not occur between power outputs or between the BGND and PGND.
  3. Turn on the switch for the upstream power supply of the server.
  4. Press the power button on the chassis of the server to power on the server.

    After the server is started properly, the button/indicator of its power switch is displayed green.

    Figure 5-17 Power button on the 2288X V5 server
    Figure 5-18 TaiShan 200 server power button

Logging In to the NetEco Client

This section describes how to log in to the NetEco client using a web browser.

Prerequisites

  • The network connection between your PC and the client IP address of the NetEco is normal and the function of the O&M plane are running properly.
  • You have obtained the user name and password for login.

Procedure

  1. In the browser address box, enter https://IP address of the NetEco server:31943, and then press Enter.

    • 192.168.8.11 is the default IP address of the NetEco.
    • Latest Chrome (Stable Channel) and Firefox (ESR Release) are recommended.

    • You are advised to set the display resolution as 1920 x 1080 or higher.

    • Make sure that the IP address of the NetEco server is not contained in the compatibility view website.

  2. Enter the User Name, Password, and click Login.

    • The preset user of NetEco is admin, the preset password is Changeme_123. This user has all the operation rights on the managed objects. After the first login, change the password in time to ensure account security and prevent unauthorized network attacks, such as data tampering. Huawei will not be liable for any security issues caused by your failure to change the preset password in time or password loss after changing.

    • If the number of online users reaches the maximum number supported by the system, a message is displayed, indicating that you cannot log in. In this case, contact the system administrator.

    • After you enter the incorrect password for three consecutive times, you must enter the verification code upon the fourth login. After you enter the incorrect password for five consecutive times, the user account or the IP address is locked for 10 minutes.

Loading the NetEco Software License

The NetEco license file is used to control the functions and management capabilities of the NetEco. Before using NetEco, you need to load a commercial license.

Prerequisites

  • You have obtained a license.
  • You have logged in to the NetEco client using a web browser.

Procedure

  1. Click Import License file when you log in to the NetEco at the first time.
  2. Click next to the License text box and select a license file.
  3. Click Upload.

    The information about the imported license file is displayed.

  4. Click Apply.

Installing NE Adapters

Install the NE adapters on the NetEco.

Prerequisites

You have obtained the adapter software installation packages.

Procedure

  1. Choose Device Management > Configuration > Device Integration.
  2. In the navigation tree on the left, choose Adapter Management and click Upload.
  3. On the page that is displayed, click + to select the file to be uploaded.
  4. Click Upload to upload the files.
  5. Select the NE adapter packages to be installed on the Adapter Management page, and click Install. Then, click Yes in the displayed dialog box.

    The time required for the installation is related to the number of adapters. Wait for the installation to complete.

General Operation: Adding a Management Domain

This section describes how to create a management domain.

Prerequisites

The management domain adapter has been preconfigured or installed.

Context

  • The management domains include Park, Building, Room, ContainerDC, Subnet, NetecoSite, FusionModule500, Modular, Room-ShapeNode, and Building-ShapeNode. You are advised to plan the subordinate relationship between management domains and devices before performing operations.
  • The NetEco is preconfigured with management domains such as cabinets, battery cabinets, buildings, containers, floors, FusionModule500, smart modules, NetEco sites, parks, PDUs, equipment rooms, and subnets. To use more management domains, you need to install the corresponding adapter software package on the NetEco.

Procedure

  1. Log in to the NetEco client.
  2. On the main menu, choose Device Management > Configuration > Planning Configuration.
  3. Choose the upper-layer node of the management domain to be added in the navigation tree on the left.
  4. In the Domain area on the lower left of the page, drag a management domain icon to the required position in the planning configuration area.

    You can adjust the shape of Room, Room–ShapeNode, Building–ShapeNode, Floor–ShapeNode, Container–ShapeNode, and NetecoSite by:

    1. Hold down Shift and click the frame to add a yellow dot.
    2. Click and move the yellow dot to design an irregular polygon.
    3. To delete a management domain, click the domain icon and select Delete under .

  5. In the right side of the view area, set Management Info.

    You can configure Management Info, Electricity Info, and Refrigeration Info for the equipment room management domain.

  6. Click on the toolbar to save the settings.
  7. Repeat steps 3 to 6 until the configuration is complete.

Example: Adding a Smart Module

This section describes how to create a module in the root node, subnet, equipment room, container, or site management domain.

Prerequisites

You have created management domains in Planning Configuration.

Procedure

  1. Log in to the NetEco client.
  2. On the main menu, choose Device Management > Configuration > Planning Configuration.
  3. Choose the management domain where you want to add a smart module from the navigation tree on the left.
  4. In the Domain area on the lower left of the page, select Modular from the drop-down list box.
  5. Select the Modular to be added and drag the modular icon to the management domain area.

    Figure 5-19 Adding the smart module in the room area

  6. Modify Management Info of the smart module as required or retain the default values.
  7. Click on the toolbar to save the settings.

Follow-up Procedure

Perform the following operations on the Planning Configuration page as required.

Related Operations

Procedure

Delete modules
You can delete one module or multiple modules in batches on the current page.
NOTE:

If a module contains subdevices, you cannot delete it. You can delete the module only after you delete subdevices in the module.

  • Delete one module.

    1. Right-click Modular and click Delete under .

    2. In the displayed Confirm dialog box, click Yes.

  • Delete multiple modules in batches.

    1. Click on the toolbar. The Batch Delete dialog box is displayed.
      Figure 5-20 Deleting multiple modules in batches
    2. In the filter box, set filter criteria to filter required modules.
    3. Select the smart module to be deleted and click Delete.
    4. In the displayed Confirm dialog box, click Yes.

Add tools
  1. Select the module for which you want to add a pillar.
  2. In the lower-left corner of the current page, click Tool.

  3. Select the Pillar component to be added and drag it to the planning configuration area.

    NOTE:

    After the component is added, you can set attributes for the component in the Component Info list in the right pane. The system automatically displays values for Parent Name and Control Type, and you do not need to manually set them, you only need to set Name.

  4. In the upper area of the current page, click .

Creating an ECC800-Pro on the NetEco

Prerequisites

  • You have logged in to the NetEco client by web browser.
  • You have created modules in Data Center Planning.

Context

For detailed operations, see iManager NetEco 6000 Device Installation and Commissioning Guide of the corresponding version.

Procedure

  1. Choose System > Configuration > Data Center Planning from the main menu. The Data Center Planning window is displayed.
  2. Click in the upper left area of the Data Center Planning window.
  3. Click Access switch to the Add Device window. You can add an ECC800-Pro device to the specified modular in the Add Device window.
    Figure 5-21 Adding an ECC800-Pro device to the modular

    Click OK, and you can view the task information, including Type, Device Name, Region, Progress, Status, Start Time, End Time, and Information in the displayed Progress window.

Translation
简体中文
Download
Updated: 2021-07-14

Document ID: EDOC1100165911

Views: 9401

Downloads: 404

Average rating:
This Document Applies to these Products

Related Version

Related Documents

Digital Signature File

Digital Signature Authentication Mode
Share
Previous Next

Copyright © 2023 Huawei Technologies Co., Ltd. All rights reserved.

You are going to visit :