Key Hardware Devices

FusionModule500 Smart Mini Data Center User Manual (Philippines, Integrated Air Conditioner)

Rate and give feedback:

Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).

ECC800-Pro
Environment Monitoring System
Cabinet Electronic Clasp Lock
PAD
WiFi Module
(Optional) Camera
(Optional) VCN510

ECC800-Pro

Product Configuration

The ECC800-Pro data center controller is used to monitor the devices and environment in the smart module. It consists of the power module and main control module. You can insert and remove the power module.

Figure 3-7 ECC800-Pro

(1) Power module

(2) Main control module

Table 3-9 ECC800-Pro environmental specifications

Item	Specifications
Operating temperature	–20°C to +50°C
Storage temperature	–40°C to +70°C
Relative humidity	5%–95% RH (non-condensing)
Altitude	0–4000 m (When the altitude is between 3000 m and 4000 m, the temperature decreases by 1°C for each additional 200 m.)

Table 3-10 ECC800-Pro structural specifications

Item	Specifications
Dimensions (L x W x H)	442 mm x 330 mm x 43.6 mm
Weight	6.3 kg (with a single power module and a main control module)
Color	Black
Installation requirements	Can be installed in a 1 U space in a standard 19-inch cabinet
Environmental protection	RoHS5, REACH, WEEE

Figure 3-8 ECC800-Pro (rear view)

(1) 53.5V DC_OUT1	(2) 53.5V DC_OUT2	(3) AC_INPUT1
(4) AC_INPUT2

Power Port

The ECC800-Pro provides four power ports, including two AC input ports (AC_INPUT1 and AC_INPUT2) and two DC output ports (DC_OUTPUT1 and DC_OUTPUT2). Table 3-11 provides the power port pin definitions.

Table 3-11 Power port pin definitions

Port Type	Pin sequence	Description
AC	Pin1	L
	Pin2	PE
	Pin3	N
DC	Pin1	48V+
DC	Pin2	48VGND

Main Control Module

Figure 3-9 ECC800-Pro collector main control module

(1) USB	(2) Status indicator	(3) AIDI_1	(4) AIDI_2
(5) COM1/AIDI_4	(6) COM3/12V	(7) WAN1	(8) LAN1/POE
(9) LAN2/POE	(10) WAN2	(11) COM4/CAN	(12) COM2/AIDI_5
(13) AIDI_3	(14) DO/12V	(15) RF_Z (802.15.4)	(16) WLAN (reserved)
(17) 4G	(18) SW button

The WLAN port is reserved and cannot be connected to a WLAN antenna for WLAN communication.

Figure 3-10 ECC800-Pro main control module (side view)

(1) SIM card slot

(2) Micro SD card slot (reserved)

Specifications

Table 3-12 Technical specifications of the ECC800-Pro main control module

Item	Specifications
Power input	Supports one AC input. Rated voltage: 200–240 V AC Rated frequency: 50/60 Hz
Power output	Output voltage: 42–58 V DC (rated voltage: 53.5 V DC) Output power of two power module supplies: 2000 W (200–240 V AC); 940 W (linear derating at 85–175 V AC) Output power of a single power module supply: 1000 W (200–240 V AC); 470 W (linear derating at 85–175 V AC)
WAN port	Supports two WAN ports. WAN1 is used to connect to the management system, and WAN2 is used for maintenance. The ports support autonegotiation of 10/100/1000 Mbit/s communication rates. Connect shielded network cables to the WAN ports.
LAN port	Supports two LAN ports, which can be connected to the LAN. The ports support autonegotiation of 10/100/1000 Mbit/s communication rates. Connect shielded network cables to the LAN ports.
RS485 serial port expansion	Output voltage: 13–15 V DC (rated voltage: 14.5 V DC) Four RS485 ports with the default communications rate of 9600 bit/s COM1–COM3 ports provide 12 V DC power. The power supply can be switched on or off and is on by default.
PoE expansion	Supports two PoE (GE) ports for expansion of the PoE bus, and supports network isolation and ring network.
AIDI expansion (RJ45)	Output voltage: 13–15 V DC (rated voltage: 14.5 V DC) Provides five universal AIDI ports for connecting to sensors such as smoke sensors, water sensors, and NTC sensors. AIDI_1 to AIDI_3 are full-function AIDI ports, and AIDI_4 to AIDI_5 are simplified AIDI ports without type identification. The power supply can be switched on or off and is on by default.
DO expansion (RJ45)	Output voltage: 13–15 V DC (rated voltage: 14.5 V DC) Supports one active DO port. The power supply can be switched on or off and is on by default.
Fault isolation	There are three groups of 12 V ports. A group has a maximum current of 660 mA, a route has a maximum current of 800 mA, and the maximum total current is 2 A. Group 1: 12 V of the AIDI_1 and DO/12V ports Group 2: 12 V of the AIDI_2, COM1/AIDI_4, and COM3/12V ports Group 3: 12 V of the AIDI_3 and COM2/AIDI_5 ports
Wireless communication	Supports wireless communication that complies with IEEE802.15.4.
4G	Supports the 4G module, SMS sending, and 3G communication, and provides a standard SIM card slot. China: 2G and 4G networks support China Unicom or China Mobile SIM cards, and 3G networks support only China Unicom SIM cards. Outside China: Select SIM cards according to the following wireless modes and frequency bands: 4G: wireless mode (FDD-LTE and TDD-LTE), coverage frequency band (B1, B3, B5, B7, B8, and B20) 3G: wireless mode (WCDMA), coverage frequency bands (B38, B40, and B41) 2G: wireless mode (GSM), coverage frequency band (900/1800 MHz) NOTE: The prerequisite for using a SIM card is that the site has signal coverage. Due to the performance limitation of the wireless module, China Telecom SIM cards are not supported.
USB	Supports USB 2.0 and 5 V, 1 A power supply. After installing the WiFi module, connect the WiFi module to the ECC800-Pro using the app on the mobile phone or tablet computer to view the basic information about the smart module, such as layout, resources, energy efficiency, environment, and alarms. You can insert a USB flash drive to export historical data and configuration files and import configuration files.
SW button	Restores the default IP address, factory settings, and user information. Supports RF_Z (802.15.4) networking.

Table 3-13 ECC800-Pro RF_Z parameters

Item	Specifications
RF_Z Operation Frequency	2405–2480 MHz
RF_Z EIRP (max.)	8 dBm

Table 3-14 ECC800-Pro 4G parameters

Item	Specifications
3G/4G operation frequency	LTE (FDD): BAND1, BAND2, BAND3, BAND4, BAND5, BAND7, BAND8, BAND20 DC-HSPA+/HSPA+/HSPA/UMTS: 850/900/1900/2100 MHz GSM/GPRS/EDGE: 850/900/1800/1900 MHz
3G/4G EIRP (max.)	23 dBm

Item

Specifications

3G/4G operation frequency

LTE (FDD): BAND1, BAND2, BAND3, BAND4, BAND5, BAND7, BAND8, BAND20

DC-HSPA+/HSPA+/HSPA/UMTS: 850/900/1900/2100 MHz

GSM/GPRS/EDGE: 850/900/1800/1900 MHz

3G/4G EIRP (max.)

23 dBm

Communications Port

The ECC800-Pro provides the following communications ports. Figure 3-11 shows the pins of the RJ45 port.

Figure 3-11 RJ45 port pins

There are four GE ports, that is, two WAN ports (WAN1 and WAN2) and two LAN ports (LAN1/POE and LAN2/POE).

Table 3-15 GE port pin definitions

Item		Description
Pin sequence	Pin1	GE1+
	Pin2	GE1-
	Pin3	GE2+
	Pin4	GE3+
	Pin5	GE3-
	Pin6	GE2-
	Pin7	GE4+
	Pin8	GE4-
Indicator	Green indicator	Linked, steady on
Indicator	Yellow indicator	ACT data communication, blinking

Table 3-16 COM1/AIDI_4, COM2/AIDI_5 port pin definitions

Item		Description
Pin sequence	Pin1	RS485+
	Pin2	RS485-
	Pin3	12V DC_OUT
	Pin4	RS485+
	Pin5	RS485-
	Pin6	DI-
	Pin7	DI+
	Pin8	GND
Indicator	Green indicator	Power output indicator Steady on: The 12 V DC output is normal. Off: No 12 V DC output is provided.

Table 3-17 COM3/12V port pin definitions

Item		Description
Pin sequence	Pin1	RS485+
	Pin2	RS485-
	Pin3	12V DC_OUT
	Pin4	RS485+
	Pin5	RS485-
	Pin6	-
	Pin7	-
	Pin8	GND
Indicator	Green indicator	Power output indicator Steady on: The 12 V DC output is normal. Off: No 12 V DC output is provided.

Table 3-18 COM4/CAN port pin definitions

Item		Description
Pin sequence	Pin1	RS485+
	Pin2	RS485-
	Pin3	-
	Pin4	RS485+
	Pin5	RS485-
	Pin6	-
	Pin7	CAN_H
	Pin8	CAN_L

The following provides the AIDI_1, AIDI_2 and AIDI_3 ports pin definitions.

Pins 1, 2, 4, and 5 identify sensor types.
Pin 3 and Pin 8 are power output ports.
Pin 6 and Pin 7 collect sensor data. Pin 7 can detect current type sensors (4–20 mA). Pin 6 and Pin 7 can detect the output status of passive dry contact type sensors. Pin 3 and Pin 7 can detect temperature sensors.

Table 3-19 AIDI_1, AIDI_2 and AIDI_3 ports pin definitions

Item		Description
Pin sequence	Pin1	Type_1
	Pin2	Type_2
	Pin3	12V DC
	Pin4	Type_3
	Pin5	Type_4
	Pin6	DI-
	Pin7	DI+
	Pin8	GND
Indicator	Green indicator	Power output indicator Steady on: The 12 V DC output is normal. Off: No 12 V DC output is provided.

Table 3-20 DO/12V port pin definitions

Item		Description
Pin sequence	Pin1	-
	Pin2	-
	Pin3	12V DC_OUT
	Pin4	-
	Pin5	-
	Pin6	DO_OUT+
	Pin7	DO_OUT-
	Pin8	GND
Indicator	Green indicator	Power output indicator Steady on: The 12 V DC output is normal. Off: No 12 V DC output is provided.

Table 3-21 USB port pin definitions

Item		Description
Pin sequence	Pin1	5V
	Pin2	DM
	Pin3	DP
	Pin4	GND

Indicators

Table 3-22 Indicators on the ECC800-Pro main control module

Indicator	Color	Name	Status	Description
RUN	Green	Running status indicator	Steady on	The power supply is normal, the program is being loaded.
			Off	The power supply is abnormal.
			Blinking at long intervals	The software runs properly (the indicator blinks at 0.5 Hz, on for 1s and then off for 1s) or the ECC800-Pro registers with the NetEco successfully.
			Blinking at short intervals	The ECC800-Pro does not register with the NetEco (the indicator blinks at 5 Hz, on for 0.125s and then off for 0.125s).
ALM	Red	Alarm indicator	Steady on	A system failure alarm is generated.
ALM	Red	Alarm indicator	Off	The system is normal.
RF_Z	Green	Communication status indicator	Blinking at long intervals	A network is set up, and no node access is allowed (the indicator blinks at 0.5 Hz, on for 1s and then off for 1s).
RF_Z	Green	Communication status indicator	Blinking at super short intervals	A network is set up, and node access is allowed (the indicator blinks at 10 Hz, on for 0.05s and then off for 0.05s).

SW Button

Table 3-23 SW button description

Function Description	Operation Description	Indicator Status
Wireless network RF_Z (802.15.4) pairing	In non-wireless network (802.15.4) pairing mode, press and hold down the button for 3s to 5s to enter the wireless network pairing mode.	The RF_Z indicator is blinking at super short intervals.
	In wireless network (802.15.4) pairing mode, press and hold down the button for 3s to 5s to exit the pairing mode; or the system automatically exits the pairing mode after 30 minutes without pressing the button.	The RF_Z indicator is blinking at long intervals.
	Press and hold down the button for more than 8s to clear network parameters.	The RF_Z indicator is steady on.
WLAN enabling	Press the button for less than 3s to enable WLAN.	None
Restoring the default IP address, factory settings, and user information	Press and hold down the button for 1 minute.	None

Power Module

Indicators

Table 3-24 Power module indicator description

Color	Name	Status	Description
Green	Power indicator	Steady on	The module has input power.
		Off	The module has no input power or is faulty.
		Blinking at long intervals	The module is being queried (the indicator blinks at 0.5 Hz, on for 1s and then off for 1s).
		Blinking at short intervals	The module application program is being loaded (the indicator blinks at 4 Hz, on for 0.125s and then off for 0.125s).
Yellow	Alarm indicator	Steady on	Power limiting warning due to ambient overtemperature; protection shutdown alarm due to ambient overtemperature or undertemperature
			Power input overvoltage or undervoltage protection
			Reverse DC input connection
			Slight current imbalance
			Output overvoltage
			Hibernation
		Off	The module generates no protection alarms.
		Blinking at long intervals	The communication between the module and the outside is interrupted (the indicator blinks at 0.5 Hz, on for 1s and then off for 1s).
Red	Fault indicator	Steady on	The module locks out due to output overvoltage.
		Steady on	The module has no output due to internal faults.
		Off	The module is normal.

Environment Monitoring System

Electrode Water Sensor

The electrode water sensor with the BOM number of 33010444 contains electrode probes and cables.

Figure 3-12 Electrode water sensor

Table 3-25 Technical specifications of the electrode water sensor

Item	Specification
Operating temperature	–40°C to +80°C
Storage temperature	–40°C to +80°C

T/H Sensor

Figure 3-13 Appearance

The T/H sensor uses an RJ45 connector.

The appearance of the T/H sensor depends on the onsite delivery.

Figure 3-14 Pins of an RJ45 connector

Table 3-26 RJ45 port pin definitions

Pin	Description
Pin1 or Pin 4	A
Pin2 or Pin 5	B
Pin3	V+
Pin6	V-
Pin7	Reserved

Table 3-27 T/H sensor specifications

Item	Specifications
Temperature measuring range	–20°C to +70°C
Temperature accuracy	±1°C
Humidity measuring range	5%–95% RH
Humidity precision	±5% RH (25°C, 20%–80% RH)
Operating temperature	–20°C to +70°C
Operating voltage	9–16 V DC
Storage temperature	–40°C to +70°C
Output	RS485

Smoke Detector

A smoke detector detects smoke around cabinets.

Figure 3-15 Smoke detector

Table 3-28 Smoke detector technical specifications

Item	Specifications
Operating voltage	9–27 V
Alarm current	< 20 mA
Indication	Monitoring: The red indicator blinks once every 3 to 8 seconds. Alarm reporting: The red indicator is steady on.
Operating temperature	–10°C to +55°C
Ambient humidity	≤ 95% RH
Dimensions (H x W x D)	31 mm x 75 mm x 51 mm (with the base)
Weight	50 g

Cabinet Electronic Clasp Lock

The cabinet electronic clasp lock is used to manage access control. It can be automatically unlocked, or manually locked and unlocked.

Figure 3-16 Cabinet electronic clasp lock

(1) LED indicator

(2) DIP switch

(3) RJ45 power port

Table 3-29 RJ45 port definitions

No.	Pin Description	Description
1	RS485+	RS485+
2	RS485-	RS485-
3	+12 V power supply	+12VDC
4	RS485+	RS485+
5	RS485-	RS485-
6	-	-
7	-	-
8	Ground	GND

Table 3-30 LED indicator status

Indicator	Color	Name	Operation	Status	Description
RUN	Green	Module running indicator	/	Blinking	The door lock is paired with the host, and the power supply is normal: The indicator blinks at 0.5 Hz (on for 1s and then off for 1s). The door lock fails to pair with the host: The indicator blinks at 4 Hz (on for 0.125s and then off for 0.125s).
			/	Off	The power supply is abnormal.
			Press SW.	Blinking intermittently at super short intervals	The indicator blinks at super short intervals for 0.5s, and then off for 0.5s. The indicator blinks at super short intervals (blinking at 10 Hz, on for 0.05s and then off for 0.05s). The cycle lasts for 5s.
ALM	Red	Alarm indicator	/	Steady on	A system failure alarm is generated.
ALM	Red	Alarm indicator	/	Off	The system is normal.

PAD

The PAD allows the wireless access from the data center management system. You can monitor the equipment in the data center and environmental parameters in real time over the app. The recommended model is T5-10.

Figure 3-17 PAD

Table 3-31 PAD structural specifications

Item	Specifications
Dimensions (L x W x H)	243 mm x 164 mm x 7.8 mm
Weight	About 460 g

Table 3-32 PAD technical specifications

Item	Specifications
Touchscreen	10.1-inch, 1920 x 1200 resolution, IPS screen, and multi-touch
Storage	Machine: 32 GB Memory: 3 GB Extension card: Micro SD, a maximum of 256 GB (non-standard configuration)
Button/Port	Touch button + power switch and volume button 3.5 mm stereo headphones port Micro SD card port MicroUSB port
Camera	Rear camera: 8-megapixel, F2.4 aperture, automatic focus Front camera: 2-megapixel, F2.4 aperture, fixed focus Sensor type: BSI Flash: not supported Video recording: rear camera up to 1080 pixels at 30 FPS; front camera up to 720 pixels at 30 FPS Zoom mode: digital zoom Photo resolution: rear camera up to 8 M (3264 x 2448 pixels); front camera up to 1.9 M (1600x1200 pixels)
Battery	Materials: Li-polymer Capacity: 5100 mAh (typical value) or 4980 mAh (rated value) WiFi connection/web page browse time: about 6.5 hours Power adapter charge time: about 3.5 hours (5 V 2 A adapter)

WiFi Module

The WiFi module provides WiFi signals for equipment such as PADs to interact with the host computer.

Figure 3-18 WiFi module

Table 3-33 Technical specifications of a WiFi module

Item	Specifications
Wireless standard	IEEE 802.11n, IEEE 802.11g, and IEEE 802.11b
Network bandwidth	11n: up to 150 Mbps 11g: up to 54 Mbps 11b: up to 11 Mbps
Frequency band	2.4–2.4835 GHz
Wireless transmission power	20 dBm (MAX EIRP)
Supported operating system	Windows 2000/XP/Vista/Linux/Win 7
Port	USB 2.0 Hi-Speed connector
Voltage range	5.0 V DC±5%
Operating temperature	–20°C to +70°C
Storage temperature	–40°C to +90°C
Relative humidity	10%–90% RH (non-condensing)
Power	< 0.8 W

(Optional) Camera

The C3220 camera is a two-megapixel infrared zoom dome camera that can be ceiling-mounted.

Figure 3-19 C3220 camera

Table 3-34 C3220 camera technical specifications

Item	Specifications
Image sensor	1/2.7'' two-megapixel progressive scan CMOS
Minimum illumination	Color: 0.002 lux (F1.2, AGC ON, 1/30s shutter speed) Black/White: 0.0005 lux (F1.2, AGC ON, 1/30s shutter speed); 0 lux (infrared illuminator enabled)
Wide dynamic range	120 dB
Focal length	2.8–12 mm
Video compression standard	H.265/H.264/MJPEG
Maximum resolution	1920x1080
Power supply	12 V DC, PoE
IP rating	IP67
Vandal resistant rating	IK10

(Optional) VCN510

Figure 3-20 Appearance
Click to enlarge

Table 3-35 Performance specifications

Item	Specifications
Device access and video storage	Supports a maximum of eight video access channels or 128 Mbit/s video access bandwidth.
Video forwarding	Supports a maximum of 32 video forwarding channels or 256 Mbit/s video forwarding bandwidth.
Video playback and download	Supports a maximum of eight video playback and download channels or 128 Mbit/s video playback and download bandwidth.
Ingress and egress bandwidth	The ingress bandwidth does not exceed 128 Mbit/s. The egress bandwidth does not exceed 256 Mbit/s.

Table 3-36 Hardware specifications

Item	Specifications
Number of disks	2
Whether the hard disk supports hot swap	No
Supported hard disk type	3 TB, 4 TB, 6 TB, or 8 TB SATA disks
CPU type and maximum number of supported CPUs	1 x ARM Cortex A17 Quad-core @Max. 1.4 GHz
Memory capacity	1 GB
Network port	Two GE network ports
Power parameters	One power module AC power (100 V AC to 240 V AC; 50 or 60 Hz)
Weight in full configuration (including disks)	≤ 5 kg
Maximum power consumption (including hard disks)	< 60 W
Dimensions (H x W x D)	43.6 mm x 442 mm x 310 mm (1 U, excluding the panel) 43.6 mm x 442 mm x 320 mm (1 U, including the panel)

ECC800-Pro
Environment Monitoring System
Cabinet Electronic Clasp Lock
PAD
WiFi Module
(Optional) Camera
(Optional) VCN510

Translation

简体中文

Download

Updated: 2021-07-14

Document ID: EDOC1100165911

Downloads: 403

Average rating:

This Document Applies to these Products

Related Version

Digital Signature File

Digital Signature Authentication Mode

Enterprise

Huawei Cloud

Carrier

Consumer

Corporate

ECC800-Pro

Product Configuration

Power Port

Main Control Module

Specifications

Communications Port

Indicators

SW Button

Power Module

Indicators

Environment Monitoring System

Electrode Water Sensor

T/H Sensor

Smoke Detector

Cabinet Electronic Clasp Lock

PAD

WiFi Module

(Optional) Camera

(Optional) VCN510

Related Version

Related Documents

Digital Signature File