Here is a tested and verified procedure to install the RSC function on the V890 of Customer Live Network:
1. Upload the RSC software
1) copy the rsc software:rsc2.2.3_packages_s9-V890.zip to system:/userbackup/sof/ through FTP client.
cd /userbackup/sof/
unzip rsc2.2.3_packages_s9-V890.zip
2) copy to the temp directory on the system:
cd /tmp
mkdir rsc
cp -r /userbackup/sof/rsc2.2.3_packages_s9-V890/* ./rsc/
2. Install the RSC software
cd /tmp
cd rsc/
pkgadd -d .
choose 'all'
choose 'yes' in all the following steps;…
at last: 'Installation of <SUNWcrsc> was successful.' means installation completed
3. Check the software installed successfully and the current RSC configuration
/usr/platform/SUNW,Sun-Fire-V890/rsc/rscadm show
Configure the RSC
cd /usr/platform/`uname -i`/rsc
./rsc-config
configure the RSC as below:
Continue with RSC setup (y|n): y
Set RSC date/time now (y|n|?) [y]: y
Server Hostname [SiteAA]:
Edit customer info field (y|n|?) [n]:
Enable RSC Ethernet Interface (y|n|s|?) [n]: y
RSC IP Mode (config|dhcp|?) [dhcp]: config
RSC IP Address []: 10.70.20.200
RSC IP Netmask [255.255.255.0]:
RSC IP Gateway []: 10.70.20.6
Enable RSC Alerts (y|n|s|?) [n]: n
Enable RSC Serial Port Interface (y|n|s|?) [n]: y
Serial port baud rate (9600|19200|38400|57600|115200) [9600]:
Serial port data bits (7|8) [8]:
Serial port parity (even|odd|none) [none]:
Serial port stop bits (1|2) [1]:
Setup RSC User Account (y|n|?) [y]:
Username []: admin
User Permissions (c,u,a,r|none|?) [cuar]:
4. Check the RSC configuration
/usr/platform/SUNW,Sun-Fire-V890/rsc/rscadm show
5. Configure the output/input device of the system
1) to check the current configuration
#eeprom
test-args: data not available.
diag-passes=1
local-mac-address?=true
scsi-initiator-id=7
oem-logo: data not available.
oem-logo?=false
oem-banner: data not available.
oem-banner?=false
ansi-terminal?=true
screen-#columns=80
screen-#rows=34
ttyb-rts-dtr-off=false
ttyb-ignore-cd=true
ttya-rts-dtr-off=false
ttya-ignore-cd=true
ttyb-mode=9600,8,n,1,-
ttya-mode=9600,8,n,1,-
output-device=screen
input-device=keyboard
auto-boot-on-error?=false
load-base=16384
auto-boot?=true
network-boot-arguments: data not available.
boot-command=boot
diag-file: data not available.
diag-device=net
boot-file: data not available.
boot-device=/pci@8,600000/SUNW,qlc@2/fp@0,0/disk@w21000014c33ba347,0:a
use-nvramrc?=true
nvramrc=devalias vx-disk01 /pci@8,600000/SUNW,qlc@2/fp@0,0/disk@w21000014c33ba34
7,0:a
devalias vx-disk04 /pci@8,600000/SUNW,qlc@2/fp@0,0/disk@w21000014c33b916a,0:a
security-mode=none
security-password: data not available.
security-#badlogins=0
verbosity=normal
fcode-debug?=false
diag-out-console=false
diag-trigger=error-reset power-on-reset
service-mode?=false
diag-script=none
diag-level=min
diag-switch?=false
error-reset-recovery=sync
Congigure as below to use RSC
#eeprom output-device= rsc-console
#eeprom input-device= rsc-console
#eeprom diag-out-console=true
#eeprom diag-script=normal
6. Access the RSC through the network management port
telnet 'the IP of the RSC'
7. Reset the host system
#sync;sync;
#shutdown -y -g0 -i6
Access the RSC through the network management port, then console to the server
telnet 'the IP of the RSC'
console
8. After the console is successfully tested fine working, restore the U2000/N2000.
Support
