S5700-28C-HI-24S

S5700 Series Switches Hardware Description (V200)

Rate and give feedback:

Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).

S5700-28C-HI-24S

Version Mapping

Table 4-993 lists the mapping between the S5700-28C-HI-24S and software versions.

Table 4-993 Version mapping

Series	Model	Software Version
S5700-HI	S5700-28C-HI-24S	V100R006C01 to V200R005C02 NOTE: This model does not match V200R003C02 or V200R003C10.

Appearance and Structure

Figure 4-395 S5700-28C-HI-24S appearance

1	Power module slot 1 NOTE: Applicable power modules: W0PSA1701 (170 W AC Power Module) ES5M0PSD1700 (170 W DC Power Module)	2	Power module slot 2 NOTE: Applicable power modules: W0PSA1701 (170 W AC Power Module) ES5M0PSD1700 (170 W DC Power Module)
3	ESD jack NOTE: Before installing or maintaining a switch, wear an ESD wrist strap and insert the other end of the ESD wrist strap into this ESD jack.	4	One console port
5	One ETH management port	6	Front card slot NOTE: Card supported: ES5D00X2SA00 (2-Port GE SFP/10GE SFP+ Front Optical Interface Card) ES5D00X4SA00 (4-Port GE SFP/10GE SFP+ Front Optical Interface Card) ES5D00G4SC00 (4-Port GE SFP Front Optical Interface Card)
7	One USB port	8	Twenty-four 100/1000BASE-X ports Applicable modules: FE optical module GE optical module GE-CWDM optical module GE copper module (works at 10 Mbit/s, 100 Mbit/s, or 1000 Mbit/s)
9	Ground screw NOTE: It is used with a ground cable. The switch has two ground screws, any of which can be used to install a ground cable.	10	Monitoring port NOTE: The monitoring port monitors the cabinet door, power module, battery power, and power supply of the air conditioner.

Port Description

100/1000BASE-X port

A 100/1000BASE-X port can send and receive data at 100 Mbit/s or 1000 Mbit/s. Table 4-994 describes the attributes of a 100/1000BASE-X port.

Table 4-994 Attributes of a 100/1000BASE-X port

Attribute	Description
Connector type	LC/PC
Optical interface attributes	Depend on the optical module used
Standards compliance	IEEE802.3z
Working mode	100/1000 Mbit/s auto-sensing

Console port

The console port is connected to a console for on-site configuration. The port must use a console cable. The console port is used when a switch is powered on for the first time. For details about the attributes of a console port, see Table 4-995.

Table 4-995 Attributes of a console port

Attribute	Description
Connector type	RJ45
Standards compliance	RS-232
Working mode	Duplex Universal Asynchronous Receiver/Transmitter (UART)
Baud rate	9600 bit/s, 19200 bit/s, 38400 bit/s, 57600 bit/s, or 115200 bit/s Default value: 9600 bit/s

ETH management port

You can connect a switch to a configuration terminal or network management workstation through the ETH management port to configure the switch locally or remotely. The port must use an Ethernet cable. You can choose to download the software package through the ETH management port in the BootROM menu. File transfer through the ETH management port is faster than transfer through the console port. For details on how to use the ETH management port, see the Configuration Guide - Basic Configurations. Table 4-996 describes the attributes of an ETH management port.

Table 4-996 Attributes of an ETH management port

Attribute	Description
Connector type	RJ45
Standards compliance	IEEE802.3
Working mode	10/100 Mbit/s auto-sensing
Maximum transmission distance	100 m

USB port

The USB port can have a USB flash drive connected to upgrade the switch, or transfer configuration files or other files. The USB port can only connect to a USB flash drive that complies with USB 2.0.

USB flash drives from different vendors differ in model compatibility and drivers. If a USB flash drive cannot be used, try to replace it with another one from a mainstream vendor. Switches support a maximum of 128 GB USB flash drives.

Indicator Description

The S5700-28C-HI-24S has similar indicators (except service port indicators) to those on the S5700-28C-HI. For details, see Indicator Description.

Power Supply Configuration

The S5700-28C-HI-24S uses pluggable power modules. It can be configured with a single power module or double power modules for 1+1 power redundancy. Pluggable AC and DC power modules can be used together in the same switch.

Figure 4-396 shows the power supply connections of dual DC power modules. After DC power is transmitted to the PWR module, the PWR module provides 12 V output voltage, and the motherboard provides power for the entire device.

Figure 4-396 Power supply connections of dual DC power modules

NEG: negative wire

RTN: positive wire

GND: 12 V reference ground

Figure 4-397 shows the power supply connections of dual AC power modules. After AC power is transmitted to the PWR module, the PWR module provides 12 V output voltage, and the motherboard provides power for the entire device.

Figure 4-397 Power supply connections of dual AC power modules

L: Live wire

N: Neutral wire

PGND: Protection ground wire

GND: 12 V reference ground

Heat Dissipation

The S5700-28C-HI-24S has three built-in fans for forced air cooling. The airflow direction is left-to-right.

Click to enlarge

This figure only shows the airflow direction and does not depict the actual device.

Technical Specifications

Table 4-997 lists technical specifications of the S5700-28C-HI-24S.

Table 4-997 Technical specifications

Item	Description
Memory (RAM)	512 MB
Flash	64 MB
Mean time between failures (MTBF)	25.5 years when a 4-port 10GE interface card is configured, 34.8 years when a 2-port 10GE interface card is configured, 36.1 years when a 4-port GE interface card is configured
Mean time to repair (MTTR)	2 hours
Availability	> 0.99999
Service port surge protection	NA
Power supply surge protection	Using AC power modules: ±6 kV in differential mode, ±6 kV in common mode Using DC power modules: ±1 kV in differential mode, ±2 kV in common mode
Dimensions (H x W x D)	44.4 mm x 442.0 mm x 220.0 mm (1.75 in. x 17.4 in. x 8.7 in.)
Weight	Empty: ≤ 5 kg (11.02 lb) Fully configured: ≤ 6.5 kg (14.33 lb)
Stack ports	Versions earlier than V200R003C00 do not support stack ports. Since V200R003C00, 10GE ports on the front card can be used as stack ports.
RPS	Not supported
PoE	Not supported
Rated voltage range	100 V AC to 240 V AC, 50/60 Hz -48 V DC to -60 V DC
Maximum voltage range	90 V AC to 264 V AC, 47 Hz to 63 Hz -36 V DC to -72 V DC
Maximum power consumption (100% throughput, full speed of fans)	80.7 W
Operating temperature	-5°C to +55°C (23°F to 131°F) NOTE: The operating temperature of the switch is -5°C to +50°C (23°F to 122°F) when it uses SFP+ optical modules with 40 km or longer transmission distances.
Storage temperature	-40°C to +70°C (-40°F to +158°F)
Noise under normal temperature (27°C, sound power)	< 60 dB(A)
Relative humidity	5% to 95%, noncondensing
Operating altitude	AC power modules configured: 0-5000 m (0-16404 ft.) DC power modules configured: 0-2000 m (0-6562 ft.)
Certification	EMC certification Safety certification Manufacturing certification
Part number	02353631

Translation

简体中文

Download

Updated: 2023-04-21

Document ID: EDOC1000013597

Downloads: 41186

Average rating:

This Document Applies to these Products

Related Version

Digital Signature File

Digital Signature Authentication Mode

Enterprise

Huawei Cloud

Carrier

Consumer

Corporate