S7X08000 (02312URW/02312URW-002: 8-Port 10GE SFP+ or 2-Port 25GE SFP28 Optical Interface Card (Only Ports 1 and 2 Support 25GE))

S5700 Series Switches Hardware Description (V200)

Rate and give feedback:

Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).

Version Mapping

Table 8-148 lists the mapping between the S7X08000 card and software versions.

Table 8-148 Version mapping

Card Model	Part Number	Software Version
S7X08000	02312URW	S5731-H, S5731S-H, and S5732-H: V200R019C10 and later versions S5735S-H: V200R021C01 and later versions S5736-S: V200R020C10 and later versions
02312URW-002	S5731-H and S5731S-H: V200R021C10SPC600 and later versions (If V200R021C10SPC500 is used, install V200R021HP0121 or a later patch. If V200R021C00SPC100 is used, install V200R021SPH013 or a later patch. After installing the patch, remove and insert the card again to register the card.) S5732-H: V200R021C10SPC600 and later versions (If V200R021C00SPC100 is used, install V200R021SPH013 or a later patch. After installing the patch, remove and insert the card again to register the card.) S5735S-H: V200R021C10SPC600 and later versions S5736-S: V200R021C10SPC600 and later versions (If V200R021C00SPC100 is used, install V200R021SPH013 or a later patch. After installing the patch, remove and insert the card again to register the card.) NOTE: If this card is used on the S5731-H24HB4XZ, S5731-H48HB4XZ, S5731S-H24HB4XZ-A, S5731S-H48HB4XZ-A, or S5732-H48XUM2CC, the initial version is V200R021C10SPC600 and does not support patches with earlier versions.

Card Model

Part Number

Software Version

S7X08000

02312URW

S5731-H, S5731S-H, and S5732-H: V200R019C10 and later versions

S5735S-H: V200R021C01 and later versions

S5736-S: V200R020C10 and later versions

02312URW-002

S5731-H and S5731S-H: V200R021C10SPC600 and later versions (If V200R021C10SPC500 is used, install V200R021HP0121 or a later patch. If V200R021C00SPC100 is used, install V200R021SPH013 or a later patch. After installing the patch, remove and insert the card again to register the card.)

S5732-H: V200R021C10SPC600 and later versions (If V200R021C00SPC100 is used, install V200R021SPH013 or a later patch. After installing the patch, remove and insert the card again to register the card.)

S5735S-H: V200R021C10SPC600 and later versions

S5736-S: V200R021C10SPC600 and later versions (If V200R021C00SPC100 is used, install V200R021SPH013 or a later patch. After installing the patch, remove and insert the card again to register the card.)

NOTE:

If this card is used on the S5731-H24HB4XZ, S5731-H48HB4XZ, S5731S-H24HB4XZ-A, S5731S-H48HB4XZ-A, or S5732-H48XUM2CC, the initial version is V200R021C10SPC600 and does not support patches with earlier versions.

Card Overview

The S7X08000 provides eight 10GE SFP+ optical ports for data access and line-rate switching by default. The port mode can be changed. After the change, the first two ports are 25GE ports, and the last six ports become unavailable.

The S7X08000 can be installed in a rear card slot of the switch models listed in Table 8-149.

Table 8-149 Applicable switch models

Card	Switch Model
S7X08000	S5731-H24T4XC S5731-H24P4XC S5731-H48T4XC S5731-H48P4XC S5731S-H24T4XC-A S5731S-H48T4XC-A S5731-H24HB4XZ S5731-H48HB4XZ S5731S-H24HB4XZ-A S5731S-H48HB4XZ-A S5732-H24UM2CC S5732-H48UM2CC S5732-H48XUM2CC S5735S-H24S4XC-A S5736-S24UM4XC S5736-S24S4XC S5736-S48S4XC

Figure 8-75 S7X08000

Functions

Table 8-150 Functions

Function	Description
Basic function	Provides eight 10GE SFP+ optical ports for data access and line-rate switching by default. You can run the set card port-config-mode 25g-port enable command to change the port mode. After this command is configured, the first two ports are 25GE ports and the last six ports become unavailable.
Hot swapping	Supported
Service ports for stacking	The service ports on the card can be used as stack ports.

Indicators and Ports

Figure 8-76 Indicators on the S7X08000

Table 8-151 Indicator description

No.	Indicator	Color	Description
1	STAT	Off	The system software is not running.
		Green	Fast blinking: The system is starting. Slow blinking: The system is running properly.
		Red	A fault that affects services has occurred. The fault cannot be rectified automatically and requires manual intervention.
2	ACT/LINK	Green	Steady on: A link is established on the port. Blinking: The port is sending or receiving data.
2	ACT/LINK	Off	No link is established on the port.

Figure 8-77 Ports on the S7X08000

1. Eight 10GE SFP+ optical ports, supporting 10GE/GE

You can run the set card port-config-mode 25g-port enable command to change the port mode. After this command is configured, the first two ports are 25GE SFP28 optical ports, and the last six ports become unavailable.

10GE SFP+ optical port

The S7X08000 provides 10GE SFP+ optical ports to transmit and receive service data at 10 Gbit/s or 1 Gbit/s. Table 8-152 lists the attributes of a 10GE SFP+ optical port.

When the card is installed on the S5731-H, S5731S-H, and S5732-H, the 10GE SFP+ optical ports support GE optical modules, GE copper modules, 10GE SFP+ optical modules, SFP+ copper cables (1 m, 3 m, 5 m, and 10 m; SFP+ to SFP+), AOC cables (3 m and 10 m; SFP+ to SFP+), and SFP+ dedicated stack cables (supported only on the S5732-H24UM2CC and S5732-H48UM2CC).

When the card is installed on the S5735S-H and S5736-S, the 10GE SFP+ optical ports support GE optical modules, GE copper modules, 10GE SFP+ optical modules (the maximum transmission distance cannot exceed 10 km), SFP+ copper cables (1 m, 3 m, 5 m, and 10 m; SFP+ to SFP+), and AOC cables (3 m and 10 m; SFP+ to SFP+).

Table 8-152 Attributes of a 10GE SFP+ optical port

Attribute	Description
Connector type	LC/PC
Optical port attributes	Depend on the optical module. For details, see GE eSFP Optical Modules, GE-CWDM eSFP Optical Modules, GE-DWDM eSFP Optical Modules, GE SFP Copper Modules, 10GE SFP+ Optical Modules, 10GE-CWDM SFP+ Optical Modules, and 10GE-DWDM SFP+ Optical Modules.

25GE SFP28 optical port

The S7X08000 provides 25GE SFP28 optical ports to transmit and receive service data at 25 Gbit/s, 10 Gbit/s, or 1 Gbit/s. Table 8-153 lists the attributes of a 25GE SFP28 optical port.

When the card is installed on the S5731-H, S5731S-H, and S5732-H, the 25GE SFP28 optical ports support 25GE optical modules, SFP28 copper cables (1 m, 3 m, and 5 m; SFP28 to SFP28), SFP28 AOC cables (3 m, 5 m, 7 m, and 10 m; SFP28 to SFP28), GE optical modules, GE copper modules, 10GE SFP+ optical modules, SFP+ copper cables (1 m, 3 m, 5 m, and 10 m; SFP+ to SFP+), and AOC cables (3 m and 10 m; SFP+ to SFP+).
When the card is installed on the S5735S-H and S5736-S, the 25GE SFP28 optical ports support 25GE optical modules, SFP28 copper cables (1 m, 3 m, and 5 m; SFP28 to SFP28), SFP28 AOC cables (3 m, 5 m, 7 m, and 10 m; SFP28 to SFP28), GE optical modules, GE copper modules, 10GE SFP+ optical modules (the maximum transmission distance cannot exceed 10 km), SFP+ copper cables (1 m, 3 m, 5 m, and 10 m; SFP+ to SFP+), and AOC cables (3 m and 10 m; SFP+ to SFP+).
When a 25GE optical module or cable is connected to a 25GE SFP28 optical port, the port can automatically adjust its rate to 25 Gbit/s.
When a 10GE optical module or cable is connected to a 25GE SFP28 optical port, the port can automatically adjust its rate to 10 Gbit/s.
Before installing a GE optical module or copper module on a 25GE SFP28 optical port, run the port mode ge command to configure the port to work at 1 Gbit/s.

Table 8-153 Attributes of a 25GE SFP28 optical port

Attribute	Description
Connector type	LC/PC
Optical port attributes	Depend on the optical module. For details, see 25GE SFP28 Optical Modules, GE eSFP Optical Modules, GE-CWDM eSFP Optical Modules, GE-DWDM eSFP Optical Modules, GE SFP Copper Modules, 10GE SFP+ Optical Modules, 10GE-CWDM SFP+ Optical Modules, and 10GE-DWDM SFP+ Optical Modules.

Technical Specifications

Table 8-154 Technical specifications

Item	Description
Physical specifications	Dimensions (H x W x D): 40 mm x 100 mm x 208 mm (1.57 in. x 3.94 in. x 8.19 in.) Weight: 0.44 kg (0.97 lb) Maximum power consumption: 33 W

Ordering Information

Ordering information is subject to updates with product version upgrades. The ordering information provided in this manual is for reference only. To obtain the latest ordering information, contact Huawei switch distributors or Huawei local office.

Table 8-155 provides the S7X08000 ordering information.

Table 8-155 Ordering information

Card Description	Card Model	Part Number
8-port 10GE SFP+ or 2-port 25GE SFP28 optical interface card (only ports 1 and 2 support 25GE)	S7X08000	02312URW 02312URW-002

Card Description

Card Model

Part Number

8-port 10GE SFP+ or 2-port 25GE SFP28 optical interface card (only ports 1 and 2 support 25GE)

S7X08000

02312URW

02312URW-002

Translation

简体中文

Download

Updated: 2023-04-21

Document ID: EDOC1000013597

Downloads: 41099

Average rating:

This Document Applies to these Products

Related Version

Digital Signature File

Digital Signature Authentication Mode

Enterprise

Huawei Cloud

Carrier

Consumer

Corporate