No se encuentran recursos de mapeo en el idioma seleccionado.
Enterprise
España [Cambiar]
Search
  • History
  • Most people search for
Asistencia Centro de documentación
S5700 Series Switches Hardware Description (V200)
Rate and give feedback:
Huawei ha traducido este documento a diferentes idiomas combinando la traducción automática con la revisión humana a fin de permitirle entender mejor su contenido. Nota: Sin importar lo avanzada que sea, la traducción automática no puede igualar la calidad que proporcionan los traductores profesionales. Huawei no asume ninguna responsabilidad por la precisión de las traducciones y recomienda consultar el documento escrito en inglés (al cual puede acceder mediante el enlace proporcionado).
S5732-H48UM2CC (02353HUB/02353HUB-002/02353SJT/02353SJT-001/02353SJT-003/02353SJT-004/02353SJT-010/02353SJT-011/02353SJT-013/02353SJT-014)

S5732-H48UM2CC (02353HUB/02353HUB-002/02353SJT/02353SJT-001/02353SJT-003/02353SJT-004/02353SJT-010/02353SJT-011/02353SJT-013/02353SJT-014)

Version Mapping

Table 4-1541 lists the mapping between the S5732-H48UM2CC chassis and software versions.

Table 4-1541 Version mapping

Series

Model

Software Version

S5732-H

S5732-H48UM2CC

02353HUB: Supported in V200R019C10SPC500 and later versions

02353HUB-002: V200R021C10SPC500 and later versions (If V200R021C00SPC100 is used, install V200R021SPH011 or a later patch.)

02353SJT: Supported in V200R019C10SPC500 and later versions

02353SJT-001: Supported in V200R019C10SPC500 and later versions

02353SJT-003: Supported in V200R019C10SPC500 and later versions

02353SJT-004: Supported in V200R019C10SPC500 and later versions

02353SJT-010: V200R021C10SPC500 and later versions (If V200R021C00SPC100 is used, install V200R021SPH011 or a later patch.)

02353SJT-011: V200R021C10SPC500 and later versions (If V200R021C00SPC100 is used, install V200R021SPH011 or a later patch.)

02353SJT-013: V200R021C10SPC500 and later versions (If V200R021C00SPC100 is used, install V200R021SPH011 or a later patch.)

02353SJT-014: V200R021C10SPC500 and later versions (If V200R021C00SPC100 is used, install V200R021SPH011 or a later patch.)

NOTE:

V200R021C01 is not supported.

There are several S5732-H48UM2CC bundles, which consists of different power supplies and ports, as listed in Table 4-1542.

Table 4-1542 S5732-H48UM2CC bundles

Part Number

Description

Remarks

02353HUB

02353HUB-002

S5732-H48UM2CC Premium(48*100M/1G/2.5G/5G/10G Ethernet ports, 4*25GE SFP28 + 2*40GE ports or 2*100GE QSFP28 ports, 1*expansion slot, PoE++, without power module)

By default, no power supply is configured.

By default, multi-GE ports support 100 Mbit/s, 1000 Mbit/s, 2.5 Gbit/s, 5 Gbit/s, and 10 Gbit/s.

02353SJT

02353SJT-010

S5732-H48UM2CC Base(48*100M/1G Ethernet ports,Optional RTU upgrade to 2.5/5/10G, 4*25GE SFP28 + 2*40GE or 2*100GE QSFP28 ports, 1*expansion slot, PoE++, without power module)

By default, no power supply is configured.

By default, multi-GE ports support 100 Mbit/s and 1000 Mbit/s. You can purchase an RTU license to increase the port rate to 2.5 Gbit/s, 5 Gbit/s, or 10 Gbit/s.

02353SJT-001

02353SJT-011

S5732-H48UM2CC 2.5&10G Bundle(36*100M/1G/2.5G, 12*100M/1G/2.5G/5G/10G Ethernet ports, Optional RTU upgrade to 5/10G, 4*25GE + 2*40GE or 2*100GE, 1*expansion slot, PoE++, 1*1000W AC power)

By default, one 1000 W AC power module is configured.

By default, the first 36 multi-GE ports support 100 Mbit/s, 1000 Mbit/s, and 2.5 Gbit/s. You can purchase an RTU license to increase the port rate to 5 Gbit/s or 10 Gbit/s.

By default, the last 12 multi-GE ports support 100 Mbit/s, 1000 Mbit/s, 2.5 Gbit/s, 5 Gbit/s, and 10 Gbit/s.

There is a label on the rear side of the device, which contains the default rate "36*2.5GE+12*10GE" supported by the multi-GE ports.

02353SJT-003

02353SJT-013

S5732-H48UM2CC 5G Bundle(48*100M/1G/2.5G/5G Ethernet ports, Optional RTU upgrade to 10G, 4*25GE SFP28 + 2*40GE or 2*100GE QSFP28 ports, 1*expansion slot, PoE++, 1*1000W AC power)

By default, one 1000 W AC power module is configured.

By default, multi-GE ports support 100 Mbit/s, 1000 Mbit/s, 2.5 Gbit/s, and 5 Gbit/s. You can purchase an RTU license to increase the port rate to 10 Gbit/s.

There is a label on the rear side of the device, which contains the default rate "48*5GE" supported by the multi-GE ports.

02353SJT-004

02353SJT-014

S5732-H48UM2CC 10G Bundle(48*100M/1G/2.5G/5G/10G Ethernet ports, 4*25GE SFP28 + 2*40GE or 2*100GE QSFP28 ports, 1*expansion slot, PoE++, 1*1000W AC power)

By default, one 1000 W AC power module is configured.

By default, multi-GE ports support 100 Mbit/s, 1000 Mbit/s, 2.5 Gbit/s, 5 Gbit/s, and 10 Gbit/s.

There is a label on the rear side of the device, which contains the default rate "48*10GE" supported by the multi-GE ports.

A pre-configured or loaded RTU (right to use) license of a device is bound to the device ESN and cannot be unbound or transferred to other devices.

For details about the RTU licenses supported by the device and how to load them, see the License Usage Guide.

The rate of MultiGE ports can be increased using the RTU license. After the license is activated, you can run the assign group-speed command and restart the device to make the configured maximum rate supported by the ports in the MultiGE port group take effect. To check the default rate of MultiGE ports, run the display device group-speed configuration command. The BaseSpeed field indicates the default rate.

A switch with part number 02353SJT-003 is as an example. The switch has a label on its real panel, which shows the default rate of multi-GE ports on the switch.

Appearance and Structure

Figure 4-586 S5732-H48UM2CC appearance

1

One PNP button

NOTICE:

To restore the factory settings and reset the switch, hold down the button for at least 6 seconds.

To reset the switch, press the button.

Resetting the switch will cause service interruption. Exercise caution when you press the PNP button.

2

Forty-eight 100M/1000M/2.5GE/5GE/10GE BASE-T PoE++ ports (multi-GE ports)

3

Four 1GE/10GE/25GE SFP28 optical ports

Applicable modules and cables:

4

Two 40GE/100GE QSFP28 optical ports

Applicable modules and cables:
NOTE:

You can run the set device port-config-mode enable command to change the working mode of SFP28 and QSFP28 optical ports. By default, the working mode of SFP28 and QSFP28 optical ports is "4 x 25GE + 2 x 40GE".

If any QSFP28 optical port is configured to work at 100 Gbit/s or split into four 25GE ports, the four SFP28 optical ports become unavailable.

5

Ground screw

NOTE:
It is used with a ground cable.

6

One USB port

7

One console port

8

One ETH management port

9

Rear card slot

NOTE:
Applicable card:

10

Fan module slot 1

NOTE:

Applicable fan module: FAN-031A-B (Fan box(B,FAN panel side exhaust))

11

Fan module slot 2

NOTE:

Applicable fan module: FAN-031A-B (Fan box(B,FAN panel side exhaust))

12

Power module slot 1

NOTE:

Applicable power module:

13

Power module slot 2

NOTE:

Applicable power module:

-

-

Port Description

100M/1000M/2.5GE/5GE/10GE BASE-T port (multi-GE port)

A 100M/1000M/2.5GE/5GE/10GE BASE-T port (multi-GE port) sends and receives service data at 100 Mbit/s, 1 Gbit/s, 2.5 Gbit/s, 5 Gbit/s, or 10 Gbit/s, and must use an Ethernet cable. If the 2.5 Gbit/s or 5 Gbit/s speed is required, the port must use an Ethernet cable of Cat5e or higher category. If the 10 Gbit/s speed is required, the port must use an Ethernet cable of Cat6A F/UTP or higher category. Table 4-1543 describes the attributes of a 100M/1000M/2.5GE/5GE/10GE BASE-T port.
Table 4-1543 Attributes of a 100M/1000M/2.5GE/5GE/10GE BASE-T port

Attribute

Description

Connector type

RJ45

Standards compliance

IEEE802.3u, IEEE802.3ab, IEEE802.3bz, IEEE802.3an

Working Mode

100/1000/2500/5000/10000 Mbit/s auto-sensing
Table 4-1544 lists the maximum transmission distances of different cables on multi-GE ports.
Table 4-1544 Maximum transmission distances of different cables on multi-GE ports

Cable Type (6-a-1 Bundle)

Multi-GE Port (Different Rates)

100M/1000M

2.5GE

5GE

10GE

Category 5e unshielded twisted pair (Cat5e UTP)

100 m

100 m
  • 55 m
  • 100 m (6-a-1 bundle only for the first 30 m)

Not recommended due to high risk

Not supported

Category 5e shielded twisted pair (Cat5e STP)

100 m

100 m

100 m

Not supported

Category 6 unshielded twisted pair (Cat6 UTP)

100 m

100 m

100 m

Not recommended due to high risk

Not supported

Category 6 shielded twisted pair (Cat6 STP)

100 m

100 m

100 m

Not supported

Category 6A unshielded twisted pair (Cat6A U/UTP)

100 m

100 m

100 m

Not recommended due to high risk

Not supported

Category 6A foiled/unshielded twisted pair (Cat6A F/UTP)

100 m

100 m

100 m

100 m

Category 6A shielded twisted pair (Cat6A STP)

100 m

100 m

100 m

100 m

Category 7 twisted pair (Cat7)

100 m

100 m

100 m

100 m

6-a-1 stands for the six-around-one cable bundle mode, with one cable in the center and six cables bundled evenly around it.

If a port works at a rate of 5 Gbit/s, you are advised not to use unshielded Ethernet cables due to the following causes:
  • 802.3bz requires that the ALSNR value for alien crosstalk between Ethernet cables be greater than 0, but the standards for Cat5e and Cat6 unshielded twisted pairs do not specify the required ALSNR value. Therefore, such cables may not meet the crosstalk requirement in 802.3bz, causing severe problems such as continuous packet loss or port flapping may occur.
  • According the cabling specification TIA TSB-5021, using Cat5e and Cat6 cables for 5G poses high risks.
  • Currently, no clear onsite testing or evaluation method is available for checking whether ALSNR of cables conforms to 802.3bz.

If a port works at a rate of 5 Gbit/s and a Cat6 shielded Ethernet cable is used, the Ethernet cable must comply with ISO 11801 PL Class E (+All) or TIA Cat 6 Channel (+All). If a Cat6A shielded Ethernet cable is used, the Ethernet cable must comply with ISO 11801 PL2 Class Ea (+All) or TIA Cat6A Channel (+All). Otherwise, serious problems such as continuous packet loss or interface flapping may occur.

If a port works at a rate of 10 Gbit/s and a Cat6A shielded Ethernet cable is used, the Ethernet cable must comply with ISO 11801 PL2 Class Ea (+All) or TIA Cat6A Channel (+All). Otherwise, serious problems such as continuous packet loss or interface flapping may occur.

If Cat5e and Cat6 unshielded twisted pairs do not meet the 5G requirement, you are advised to replace them with shielded twisted pairs or reduce the rate of ports to 2.5G.

If Cat5E, Cat6, or Cat6A unshielded twisted pairs are used on electrical ports working at 10 Gbit/s, severe problems such as continuous packet loss or port flapping may occur.

1GE/10GE/25GE SFP28 optical port

A 1GE/10GE/25GE SFP28 optical port sends and receives service data at 1 Gbit/s, 10 Gbit/s, or 25 Gbit/s. Table 4-1521 describes the attributes of a 1GE/10GE/25GE SFP28 optical port.

Table 4-1545 Attributes of a 1GE/10GE/25GE SFP28 optical port

Attribute

Description

Connector Type

LC/PC

Optical port attributes

Depending on the optical module or cable in use

Standards compliance

IEEE802.3z, IEEE802.3ae, and IEEE802.3by

Working mode
  • When a 25GE optical module or cable is connected to a port, the port can automatically adjust its rate to 25 Gbit/s.
  • When a 10GE optical module or cable is connected to a port, the port can automatically adjust its rate to 10 Gbit/s.
  • Before installing a GE optical module or copper module on a port, run the port mode ge command to configure the port to work at 1 Gbit/s.

40GE/100GE QSFP28 optical port

A 40GE/100GE QSFP28 optical port sends and receives service traffic at 40 Gbit/s or 100 Gbit/s. Table 4-1546 describes the attributes of a QSFP28 optical port.
Table 4-1546 Attributes of a QSFP28 optical port

Attribute

Description

Connector type

MPO/LC

Optical port attributes

Depend on the optical module used

Standards compliance

IEEE802.3ba

Console port

The console port is connected to a console for on-site configuration. The port must use a console cable. The console port is used when a switch is powered on for the first time. For details about the attributes of a console port, see Table 4-1547.
Table 4-1547 Attributes of a console port

Attribute

Description

Connector type

RJ45

Standards compliance

RS-232

Working mode

Duplex Universal Asynchronous Receiver/Transmitter (UART)

Baud rate

9600 bit/s, 19200 bit/s, 38400 bit/s, 57600 bit/s, or 115200 bit/s

Default value: 9600 bit/s

ETH management port

You can connect a switch to a configuration terminal or network management workstation through the ETH management port to configure the switch locally or remotely. The port must use an Ethernet cable. You can choose to download the software package through the ETH management port in the BootLoad menu. File transfer through the ETH management port is faster than transfer through the console port. Table 4-1548 describes the attributes of an ETH management port.
Table 4-1548 Attributes of an ETH management port

Attribute

Description

Connector type

RJ45

Standards compliance

IEEE802.3

Working mode

10/100 Mbit/s auto-sensing

Maximum transmission distance

100 m
In V200R012C00 and later versions, you can log in to the switch that contains the ETH management port for the first time through the ETH port. For details, see "First Login to a Switch" in the Configuration Guide - Basic Configuration. If you have logged in to the device for the first time by pressing and holding the MODE button for 6 seconds or longer and saved the configuration, the default configuration on the ETH port will be cleared. In this case, you cannot log in to the switch for the first time through the ETH port. You are advised to log in to the switch for the first time through the ETH port.

USB port

The USB port can have a USB flash drive connected to upgrade the switch, or transfer configuration files or other files. The USB port can only connect to a USB flash drive that complies with USB 2.0.

USB flash drives from different vendors differ in model compatibility and drivers. If a USB flash drive cannot be used, try to replace it with another one from a mainstream vendor. Switches support a maximum of 128 GB USB flash drives.

Indicator Description

The S5732-H48UM2CC has the same types of indicators as the S5732-H24UM2CC. For details, see Indicator Description.

Power Supply Configuration

The switch is a PoE switch and supports two power module slots, each of which can have a 1000 W PoE or 600 W PoE power module installed. Pluggable AC and DC PoE power modules can be used together in the same switch.

Table 4-1549 Power supply configurations

Power Module 1

Power Module 2

Available PoE Power

Maximum Number of Ports (Fully Loaded)

1000 W AC (220 V)

1000 W DC

–

621 W
  • 802.3af (15.4 W per port): 40
  • 802.3at (30 W per port): 20
  • 802.3bt (60 W per port): 10

1000 W AC (110 V)

–

526 W
  • 802.3af (15.4 W per port): 34
  • 802.3at (30 W per port): 17
  • 802.3bt (60 W per port): 8

1000 W AC (220 V)

1000 W DC

1000 W AC (220 V)

1000 W DC

1571 W
  • 802.3af (15.4 W per port): 48
  • 802.3at (30 W per port): 48
  • 802.3bt (60 W per port): 26

1000 W AC (110 V)

1000 W DC

1000 W AC (110 V)

1381 W
  • 802.3af (15.4 W per port): 48
  • 802.3at (30 W per port): 46
  • 802.3bt (60 W per port): 23

600 W AC (220 V)

–

241 W
  • 802.3af (15.4 W per port): 15
  • 802.3at (30 W per port): 8
  • 802.3bt (60 W per port): 4

600 W AC (220 V)

600 W AC (220 V)

811 W
  • 802.3af (15.4 W per port): 48
  • 802.3at (30 W per port): 27
  • 802.3bt (60 W per port): 13

1000 W AC (220 V)

1000 W DC

600 W AC (220 V)

1191 W
  • 802.3af (15.4 W per port): 48
  • 802.3at (30 W per port): 39
  • 802.3bt (60 W per port): 19

When a switch has two power modules installed, the two power modules work in redundancy mode to provide power for the chassis and in load balancing mode to provide power for PDs.

Heat Dissipation

The S5732-H48UM2CC uses pluggable fan modules for forced air cooling. Air flows in from the left, right, and front sides, and exhausts from the rear panel.

This figure only shows the airflow direction and does not depict the actual device.

Technical Specifications

Table 4-1550 lists technical specifications of the S5732-H48UM2CC.

Table 4-1550 Technical specifications

Item

Description

Memory (RAM)

4 GB

Flash

2 GB in total. To view the available flash memory size, run the display version command.

Mean time between failures (MTBF)

32.38 years

Mean time to repair (MTTR)

2 hours

Availability

> 0.99999

Service port surge protection

Common mode: ±6 kV

Power supply surge protection
  • Using AC power modules: ±6 kV in differential mode, ±6 kV in common mode
  • Using DC power modules: ±2 kV in differential mode, ±4 kV in common mode

Dimensions (H x W x D)
  • Basic dimensions (excluding the parts protruding from the body): 43.6 mm x 442.0 mm x 420.0 mm (1.72 in. x 17.4 in. x 16.5 in.)
  • Maximum dimensions (the depth is the distance from ports on the front panel to the handle on the rear panel): 43.6 mm x 442.0 mm x 446.0 mm (1.72 in. x 17.4 in. x 17.6 in.)

Weight (including package)

Without power modules: 8.4 kg (18.52 lb)

Including one power module: 9.5 kg (20.94 lb)

Stack ports

Any Ethernet electrical ports (10GE), optical ports on the front panel (25GE/40GE/100GE), or optical ports on the card (10GE/25GE/40GE/100GE)

RTC

Supported

RPS

Not supported

PoE

Supported

Rated voltage range
  • AC input: 100 V AC to 130 V AC, 200 V AC to 240 V AC, 50/60 Hz
  • High-Voltage DC input: 240 V DC
  • DC input: -48 V DC to -60 V DC

Maximum voltage range
  • AC input: 90 V AC to 290 V AC, 45 Hz to 65 Hz
  • High-Voltage DC input: 190 V DC to 290 V DC
  • DC input: -38.4 V DC to -72 V DC

Maximum power consumption (100% throughput, full speed of fans)
  • Not providing the PoE function: 347 W (without card)
  • 100% PoE loads: 2043 W (PoE: 1571 W, without card)

Typical power consumption (30% of traffic load, tested according to ATIS standard)

215 W (without card)

Operating temperature
-5°C to +45°C (23°F to 113°F) at an altitude of 0-1800 m (0-5906 ft.)
NOTE:

When the altitude is 1800-5000 m (5906-16404 ft.), the highest operating temperature reduces by 1°C (1.8°F) every time the altitude increases by 220 m (722 ft.).

The switch cannot be started when the ambient temperature is lower than 0°C (32°F).

The operating temperature of the switch is -5°C to 40°C (23°F to 104°F) when it uses QSFP-100G-ER4 optical module.

Storage temperature

-40°C to +70°C (-40°F to +158°F)

Noise under normal temperature (27°C, sound power)

< 59.2 dB(A)

Relative humidity

5% to 95%, noncondensing

Operating altitude

0-5000 m (0-16404 ft.)

Certification
  • EMC certification
  • Safety certification
  • Manufacturing certification

Part number

02353HUB

02353HUB-002

02353SJT

02353SJT-001

02353SJT-003

02353SJT-004

02353SJT-010

02353SJT-011

02353SJT-013

02353SJT-014
Traducción
简体中文
Descargar
Updated: 2023-04-21

N.° del documento: EDOC1000013597

Vistas:4321346

Descargas: 41388

Average rating:
This Document Applies to these Products

Related Version

Documentos relacionados

Digital Signature File

Digital Signature Authentication Mode
Share
Anterior Siguiente

Copyright © 2023 Huawei Technologies Co., Ltd. Todos los derechos reservados.

You are going to visit :