Version Mapping
Table 4-761 lists the mapping between the S5710-52C-PWR-EI chassis and software versions.
Table 4-761 Version mappingSeries
|
Model
|
Software Version
|
|---|
S5710-EI
|
S5710-52C-PWR-EI
|
V200R002C00 to V200R005C02
NOTE: This model does not match V200R003C02, V200R003C10, or V200R005C01.
|
Appearance and Structure
Figure 4-304 S5710-52C-PWR-EI appearance![]()
1
|
Forty-eight PoE+ 10/100/1000BASE-T ports
|
2
|
Four 10GE SFP+ ports
Applicable modules and cables:
|
3
|
One ETH management port
|
4
|
One mini USB port
|
5
|
One console port
|
6
|
One USB port
|
7
|
Ground screw
|
8
|
Rear card slot 1
|
9
|
Rear card slot 2
|
10
|
ESN label
NOTE: You can draw it out to view the ESN and MAC address of the switch.
|
11
|
Power module slot 2
|
12
|
Power module slot 1
|
Port Description
10/100/1000BASE-T port
A 10/100/1000BASE-T
Ethernet electrical port sends and receives service data at 10/100/1000
Mbit/s, and must use an
Ethernet cable.
Table 4-762 describes the attributes
of a 10/100/1000BASE-T Ethernet electrical port.
Table 4-762 Attributes of a 10/100/1000BASE-T Ethernet electrical port
Attribute
|
Description
|
Connector type
|
RJ45
|
Standards compliance
|
IEEE802.3, IEEE802.3u, IEEE802.3ab
|
Working mode
|
10/100/1000 Mbit/s auto-sensing
|
Maximum transmission distance
|
100 m
|
10GE SFP+ port
A 10GE SFP+ Ethernet optical port supports auto-sensing to 1000 Mbit/s. It sends and receives service data at 1000 Mbit/s or 10 Gbit/s.
Table 4-763 describes the attributes of a 10GE SFP+ Ethernet optical port.
Table 4-763 Attributes of a 10GE SFP+ portAttribute
|
Description
|
|---|
Connector type
|
LC/PC
|
Optical port attributes
|
Depend on the optical module used
|
Standards compliance
|
IEEE802.3ae
|
Working mode
|
GE/10GE auto-sensing
|
Console port
The console port is connected
to a console for on-site configuration. The port must use a
console cable. The console port is
used when a switch is powered on for the first time. For details about
the attributes of a console port, see
Table 4-764.
Table 4-764 Attributes of a console port
Attribute
|
Description
|
Connector type
|
RJ45
|
Standards compliance
|
RS-232
|
Working mode
|
Duplex Universal Asynchronous Receiver/Transmitter (UART)
|
Baud rate
|
9600 bit/s, 19200 bit/s, 38400 bit/s, 57600 bit/s, or 115200
bit/s
Default value: 9600 bit/s
|
Mini USB port
The mini USB port is connected
to a console for on-site configuration. When both the Mini USB and
console port have a cable connected, only the Mini USB port works.
ETH management port
You can connect a switch to a configuration terminal or network management workstation through the ETH management port to configure the switch locally or remotely. The port must use an
Ethernet cable. You can choose to download the software package through the ETH management port in the BootROM menu. File transfer through the ETH management port is faster than transfer through the console port. For
details on how to use the ETH management port, see the
Configuration Guide - Basic Configurations.
Table 4-765 describes the attributes of an ETH management port.
Table 4-765 Attributes of an ETH management port
Attribute
|
Description
|
Connector type
|
RJ45
|
Standards compliance
|
IEEE802.3
|
Working mode
|
10/100 Mbit/s auto-sensing
|
Maximum transmission distance
|
100 m
|
USB port
The USB port can have a USB flash drive connected to upgrade the switch, or transfer configuration files or other files. The USB port can only connect to a USB flash drive that complies with USB 2.0.
![]()
USB flash drives from different vendors differ in model compatibility and drivers. If a USB flash drive cannot be used, try to replace it with another one from a mainstream vendor. Switches support a maximum of 128 GB USB flash drives.
Indicator Description
The S5710-52C-PWR-EI has the same types of indicators as the S5710-28C-PWR-EI-AC. For details, see Indicator Description.
Power Supply Configuration
The S5710-52C-PWR-EI is a PoE switch and uses 580 W or 1150 W AC PoE power modules. It has two power module slots. Table 4-766 lists its power supply configurations.
Table 4-766 Power supply configurationsPower Module 1
|
Power Module 2
|
Available PoE Power
|
Maximum Number of Ports (Fully Loaded)
|
|---|
580 W
|
–
|
369.6 W
|
- 802.3af (15.4 W per port): 24
- 802.3at (30 W per port): 12
|
580 W
|
580 W
|
739.2 W
|
- 802.3af (15.4 W per port): 48
- 802.3at (30 W per port): 24
|
1150 W
|
–
|
785.4 W
|
- 802.3af (15.4 W per port): 48
- 802.3at (30 W per port): 26
|
1150 W
|
1150 W
|
1440 W
|
- 802.3af (15.4 W per port): 48
- 802.3at (30 W per port): 48
|
![]()
When a switch has two power modules installed, the two power modules work in redundancy mode to provide power for the chassis and in load balancing mode to provide power for PDs.
Figure 4-305 shows the power supply mode of dual AC PoE power modules (PWR1 and PWR2). After AC power is transmitted to the PWR modules, the PWR modules provide 12 V and -53 V outputs. The outputs are combined on the motherboard, which then provides 12 V voltage for the switch and -53 V voltage for the PDs.
Figure 4-305 Power supply by dual AC PoE power modules![]()
L: live wire
|
N: neutral wire
|
PGND: protection ground wire
|
GND: 12 V reference ground
|
RTN: -53 V reference ground
|
Heat Dissipation
The S5710-52C-PWR-EI has five built-in fans for forced air cooling. The airflow direction is left-to-right.
![]( "Click to enlarge")
![]()
This figure only shows the airflow direction and does not depict the actual device.
Technical Specifications
Table 4-767 lists technical specifications of the S5710-52C-PWR-EI.
Table 4-767 Technical specificationsItem
|
Description
|
|---|
Memory (RAM)
|
512 MB
|
Flash
|
200 MB
|
Mean time between failures (MTBF)
|
36.86 years when an 8-port GE optical card is configured, 36.35 years when an 8-port GE electrical card is configured, 35.27 years when a 2-port 10GE interface card is configured
|
Mean time to repair (MTTR)
|
2 hours
|
Availability
|
> 0.99999
|
Service port surge protection
|
Common mode: ±1 kV
|
Power supply surge protection
|
- Using 580 W AC power modules: ±6 kV in differential mode, ±6 kV in common mode
- Using 1150 W AC power modules: ±2 kV in differential mode, ±4 kV in common mode
|
Dimensions (H x W x D)
|
44.4 mm x 442.0 mm x 420.0 mm (1.75 in. x 17.4 in. x 16.5 in.)
When 1150 W power modules are installed, they stretch out from the chassis. Therefore, the total depth of the switch changes to 507.3 mm (19.97 in.).
|
Weight
|
- Empty: ≤ 6 kg (13.23 lb)
- Fully configured: ≤ 10 kg (22.05 lb)
|
Stack ports
|
Four fixed 10GE SFP+ ports on the front panel or ports on the 2-port 10GE rear card
|
RPS
|
Not supported
|
PoE
|
Supported
|
Rated voltage range
|
100 V AC to 240 V AC, 50/60 Hz
|
Maximum voltage range
|
90 V AC to 264 V AC, 47 Hz to 63 Hz
|
Maximum power consumption (100% throughput, 100% PoE loads, full speed of fans)
|
Using two 580 W power modules
- No card: 1023 W (system power consumption: 283 W, PoE: 740 W)
- Two 8-port GE electrical card: 1035 W (system power consumption: 295 W, PoE: 740 W)
- Two 8-port GE optical card: 1043 W (system power consumption: 303 W, PoE: 740 W)
- Two 2-port 10GE optical card: 1040 W (system power consumption: 300 W, PoE: 740 W)
Using two 1150 W power modules
- No card: 1605 W (system power consumption: 165 W, PoE: 1440 W)
- Two 8-port GE electrical card: 1625 W (system power consumption: 185 W, PoE: 1440 W)
- Two 8-port GE optical card: 1635 W (system power consumption: 195 W, PoE: 1440 W)
- Two 2-port 10GE optical card: 1633 W (system power consumption: 193 W, PoE: 1440 W)
|
Operating temperature
|
0°C to 50°C (32°F to 122°F) at an altitude of 0-1800 m (0-5906 ft.)
NOTE: When the altitude is 1800-5000 m (5906-16404 ft.), the highest operating temperature reduces by 1°C (1.8°F) every time the altitude increases by 220 m (722 ft.).
|
Storage temperature
|
-40°C to +70°C (-40°F to +158°F)
|
Noise under normal temperature (27°C, sound power)
|
< 60 dB(A)
|
Relative humidity
|
5% to 95%, noncondensing
|
Operating altitude
|
0-5000 m (0-16404 ft.)
|
Certification
|
- EMC certification
- Safety certification
- Manufacturing certification
|
Part number
|
02355886
|
