S5732-H48S6Q (02353AJU/02353AJU-001/02353AJU-003/02353AJU-004) - S5700 Series Switches Hardware Description (V200)

S5700 Series Switches Hardware Description (V200)

Rate and give feedback:

Huawei ha traducido este documento a diferentes idiomas combinando la traducción automática con la revisión humana a fin de permitirle entender mejor su contenido. Nota: Sin importar lo avanzada que sea, la traducción automática no puede igualar la calidad que proporcionan los traductores profesionales. Huawei no asume ninguna responsabilidad por la precisión de las traducciones y recomienda consultar el documento escrito en inglés (al cual puede acceder mediante el enlace proporcionado).

S5732-H48S6Q (02353AJU/02353AJU-001/02353AJU-003/02353AJU-004)

Version Mapping

Table 4-1510 lists the mapping between the S5732-H48S6Q chassis and software versions.

Table 4-1510 Version mapping

Series	Model	Software Version
S5732-H	S5732-H48S6Q	02353AJU: V200R019C00 and later versions 02353AJU-001: V200R020C10 and later versions 02353AJU-003: V200R021C10SPC500 and later versions (If V200R021C00SPC100 is used, install V200R021SPH011 or a later patch.) 02353AJU-004: V200R021C10SPC600 and later versions (If V200R021C00SPC100 is used, install V200R021SPH013 or a later patch.) NOTE: V200R021C01 is not supported.

Series

Model

Software Version

S5732-H

S5732-H48S6Q

02353AJU: V200R019C00 and later versions

02353AJU-001: V200R020C10 and later versions

02353AJU-003: V200R021C10SPC500 and later versions (If V200R021C00SPC100 is used, install V200R021SPH011 or a later patch.)

02353AJU-004: V200R021C10SPC600 and later versions (If V200R021C00SPC100 is used, install V200R021SPH013 or a later patch.)

NOTE:

V200R021C01 is not supported.

Appearance and Structure

Figure 4-581 S5732-H48S6Q appearance

1	Forty-four 1000BASE-X ports Applicable modules: GE optical module GE-CWDM optical module GE-DWDM optical module GE copper module (works at 10 Mbit/s, 100 Mbit/s, or 1000 Mbit/s)	2	Four 10GE SFP+ ports Applicable modules and cables: GE optical module GE-CWDM optical module GE-DWDM optical module GE copper module (100M/1000M auto-sensing) 10GE SFP+ optical module (OSXD22N00 not supported) 10GE-CWDM optical module 10GE-DWDM optical module 1 m, 3 m, 5 m, and 10 m SFP+ high-speed copper cables 3 m and 10 m SFP+ AOC cables
3	Six 40GE/100GE QSFP+ optical ports Applicable modules and cables: QSFP+ optical module 1 m, 3 m, and 5 m QSFP+ to QSFP+ high-speed copper cables 10 m QSFP+ to QSFP+ AOC cable QSFP28 optical module (supported in V200R020C00 and later versions, with a license loaded) 1 m QSFP28 to QSFP28 high-speed copper cable (supported in V200R020C00 and later versions, with a license loaded) 10 m QSFP28 to QSFP28 AOC cable (supported in V200R020C00 and later versions, with a license loaded) 2 m QSFP28 dedicated stack cable (supported in V200R020C10 and later versions) NOTE: A QSFP+ optical port cannot be split into four 10GE ports, regardless of whether the port uses a QSFP28 or QSFP+ optical module. By default, a QSFP+ optical port is a 40GE port. In V200R020C00 and later versions, a license can be loaded to increase the port rate to 100 Gbit/s. After the license is activated, run the assign port-type 100GE command and restart the switch to configure the port as a 100GE port.	4	Ground screw NOTE: It is used with a ground cable.
5	SSD card slot NOTE: This slot is reserved for future use.	6	One console port
7	One ETH management port	8	One USB port
9	One PNP button NOTICE: To restore the factory settings and reset the switch, hold down the button for at least 6 seconds. To reset the switch, press the button. Resetting the switch will cause service interruption. Exercise caution when you press the PNP button.	10	Fan module slot 1 NOTE: Applicable fan module: FAN-031A-B (Fan box(B,FAN panel side exhaust))
11	Fan module slot 2 NOTE: Applicable fan module: FAN-031A-B (Fan box(B,FAN panel side exhaust))	12	Fan module slot 3 NOTE: Applicable fan module: FAN-031A-B (Fan box(B,FAN panel side exhaust))
13	Fan module slot 4 NOTE: Applicable fan module: FAN-031A-B (Fan box(B,FAN panel side exhaust))	14	Power module slot 1 NOTE: Applicable power module: PAC600S12-CB (600 W AC&240 V DC Power Module) PAC600S12-EB (600 W AC&240 V DC Power Module) PAC600S12-DB (600 W AC&240 V DC Power Module) (applicable in V200R020C10 and later versions) PDC1000S12-DB (1000 W DC Power Module)
15	Power module slot 2 NOTE: Applicable power module: PAC600S12-CB (600 W AC&240 V DC Power Module) PAC600S12-EB (600 W AC&240 V DC Power Module) PAC600S12-DB (600 W AC&240 V DC Power Module) (applicable in V200R020C10 and later versions) PDC1000S12-DB (1000 W DC Power Module)	-	-

Port Description

1000BASE-X Ethernet Optical Port

When a 1000BASE-X port uses a GE optical module, it can only transmit and receive data at 1000 Mbit/s and does not support the 100 Mbit/s transmission speed. When a 1000BASE-X port uses a GE copper module, it can transmit and receive data at 10 Mbit/s, 100 Mbit/s, or 1000 Mbit/s. Table 4-1511 describes the attributes of a 1000BASE-X Ethernet optical port.

Table 4-1511 Attributes of a 1000BASE-X Ethernet optical port

Attribute	Description
Connector type	LC/PC
Optical port attributes	Depend on the module used
Standards compliance	IEEE802.3z

10GE SFP+ optical port

A 10GE SFP+ Ethernet optical port supports auto-sensing to 1000 Mbit/s. It sends and receives service data at 1000 Mbit/s or 10 Gbit/s. Table 4-1512 describes the attributes of a 10GE SFP+ Ethernet optical port.

Table 4-1512 Attributes of a 10GE SFP+ port

Attribute	Description
Connector type	LC/PC
Optical port attributes	Depend on the optical module used
Standards compliance	IEEE802.3ae
Working mode	GE/10GE auto-sensing

40GE QSFP+ optical port

A 40GE QSFP+ optical port sends and receives service traffic at 40 Gbit/s. Table 4-1513 describes the attributes of a QSFP+ optical port.

Table 4-1513 Attributes of a QSFP+ optical port

Attribute	Description
Connector type	MPO/LC
Optical port attributes	Depend on the optical module used
Standards compliance	IEEE802.3ba

Console port

The console port is connected to a console for on-site configuration. The port must use a console cable. The console port is used when a switch is powered on for the first time. For details about the attributes of a console port, see Table 4-1514.

Table 4-1514 Attributes of a console port

Attribute	Description
Connector type	RJ45
Standards compliance	RS-232
Working mode	Duplex Universal Asynchronous Receiver/Transmitter (UART)
Baud rate	9600 bit/s, 19200 bit/s, 38400 bit/s, 57600 bit/s, or 115200 bit/s Default value: 9600 bit/s

ETH management port

You can connect a switch to a configuration terminal or network management workstation through the ETH management port to configure the switch locally or remotely. The port must use an Ethernet cable. You can choose to download the software package through the ETH management port in the BootLoad menu. File transfer through the ETH management port is faster than transfer through the console port. Table 4-1515 describes the attributes of an ETH management port.

Table 4-1515 Attributes of an ETH management port

Attribute	Description
Connector type	RJ45
Standards compliance	IEEE802.3
Working Mode	10/100 Mbit/s auto-sensing
Maximum transmission distance	100 m

In V200R012C00 and later versions, you can log in to the switch that contains the ETH management port for the first time through the ETH port. For details, see "First Login to a Switch" in the Configuration Guide - Basic Configuration. If you have logged in to the switch for the first time by pressing and holding the MODE button for 6 seconds or longer and saved the configuration, the default configuration on the ETH port will be cleared. In this case, you cannot log in to the switch for the first time through the ETH port. You are advised to log in to the switch for the first time through the ETH port.

USB port

The USB port can have a USB flash drive connected to upgrade the switch, or transfer configuration files or other files. The USB port can only connect to a USB flash drive that complies with USB 2.0.

USB flash drives from different vendors differ in model compatibility and drivers. If a USB flash drive cannot be used, try to replace it with another one from a mainstream vendor. Switches support a maximum of 128 GB USB flash drives.

Indicator Description

The S5732-H48S6Q has the same types of indicators as the S5732-H24S6Q. For details, see Indicator Description.

Power Supply Configuration

The switch can use a single power module or double power modules for 1+1 power redundancy. Pluggable AC and DC power modules can be used together in the same switch.

Heat Dissipation

The S5732-H48S6Q uses pluggable fan modules for forced air cooling. Air flows in from the front side and exhausts from the rear panel.

This figure only shows the airflow direction and does not depict the actual device.

Technical Specifications

Table 4-1516 lists technical specifications of the S5732-H48S6Q.

Table 4-1516 Technical specifications

Item	Description
Memory (RAM)	4 GB
Flash	2 GB in total. To view the available flash memory size, run the display version command.
Mean time between failures (MTBF)	56.87 years
Mean time to repair (MTTR)	2 hours
Availability	> 0.99999
Service port surge protection	N/A
Power supply surge protection	Using AC power modules: ±6 kV in differential mode, ±6 kV in common mode Using DC power modules: ±2 kV in differential mode, ±4 kV in common mode
Dimensions (H x W x D)	Basic dimensions (excluding the parts protruding from the body): 43.6 mm x 442.0 mm x 420.0 mm (1.72 in. x 17.4 in. x 16.5 in.) Maximum dimensions (the depth is the distance from ports on the front panel to the handle on the rear panel): 43.6 mm x 442.0 mm x 446.0 mm (1.72 in. x 17.4 in. x 17.6 in.)
Weight (with packaging)	9.2 kg (20.28 lb)
Stack ports	Any QSFP+ ports
RTC	Supported
RPS	Not supported
PoE	Not supported
Rated voltage range	AC input: 100 V AC to 240 V AC, 50/60 Hz High-Voltage DC input: 240 V DC DC input: -48 V DC to -60 V DC
Maximum voltage range	AC input: 90 V AC to 290 V AC, 45 Hz to 65 Hz High-Voltage DC input: 190 V DC to 290 V DC DC input: -38.4 V DC to -72 V DC
Maximum power consumption (100% throughput, full speed of fans)	255 W
Typical power consumption (30% of traffic load, tested according to ATIS standard)	142 W
Operating temperature	-5°C to +45°C (23°F to 113°F) at an altitude of 0-1800 m (0-5906 ft.) NOTE: When the altitude is 1800-5000 m (5906-16404 ft.), the highest operating temperature reduces by 1°C (1.8°F) every time the altitude increases by 220 m (722 ft.). The switch cannot be started when the ambient temperature is lower than 0°C (32°F). The operating temperature of the switch is -5°C to 40°C (23°F to 104°F) when it uses QSFP-100G-ER4 optical module.
Storage temperature	-40°C to +70°C (-40°F to +158°F)
Noise under normal temperature (27°C, sound power)	< 65 dB(A)
Relative humidity	5% to 95%, noncondensing
Operating altitude	0-5000 m (0-16404 ft.)
Certification	EMC certification Safety certification Manufacturing certification
Part number	02353AJU 02353AJU-001 02353AJU-003 02353AJU-004

Traducción

简体中文

Descargar

Updated: 2023-04-21

N.° del documento: EDOC1000013597

Vistas:4319834

Descargas: 41383

Average rating:

This Document Applies to these Products

Related Version

Documentos relacionados

Digital Signature File

Digital Signature Authentication Mode