S5736-S48S4X-A - S5700 Series Switches Hardware Description (V200)

S5700 Series Switches Hardware Description (V200)

Rate and give feedback:

Huawei ha traducido este documento a diferentes idiomas combinando la traducción automática con la revisión humana a fin de permitirle entender mejor su contenido. Nota: Sin importar lo avanzada que sea, la traducción automática no puede igualar la calidad que proporcionan los traductores profesionales. Huawei no asume ninguna responsabilidad por la precisión de las traducciones y recomienda consultar el documento escrito en inglés (al cual puede acceder mediante el enlace proporcionado).

S5736-S48S4X-A

Overview

Table 4-2018 Basic information about the S5736-S48S4X-A

Item	Details
Description	S5736-S48S4X-A base (48GE SFP ports, optional RTU upgrade to 10G, 410GE SFP+ ports, AC power supply, front access)
Part Number	98011606
Model	S5736-S48S4X-A
First supported version	V200R020C30

Components

Figure 4-696 S5736-S48S4X-A appearance

1	Forty-eight 1000BASE-X ports NOTE: A RTU license (L-P1GUPG10G-S57S) can be loaded to increase the port rate to 10 Gbit/s.	2	Four 10GE SFP+ optical ports
3	One console port	4	One ETH management port
5	One PNP button NOTICE: To restore the factory settings and reset the switch, hold down the button for at least 6 seconds. To reset the switch, press the button. Resetting the switch will cause service interruption. Exercise caution when you press the PNP button.	6	AC socket NOTE: It is used with an AC power cable.
7	Ground screw NOTE: It is used with a ground cable.	-	-

Ports

Table 4-2019 Ports on the S5736-S48S4X-A

Port	Connector Type	Description	Available Components
1000BASE-X port	SFP	A 1000BASE-X port can send and receive data at 1000 Mbit/s. A license can be loaded to increase the port rate to 10 Gbit/s.	GE eSFP optical modules GE SFP copper module 10GE SFP+ optical modules (need a license loaded, OSXD22N00 not supported, and the maximum transmission distance cannot exceed 10 km) 1 m, 3 m, 5 m, and 10 m SFP+ high-speed copper cables (need a license loaded) 3 m and 10 m SFP+ AOC cables (need a license loaded) 0.5 m and 1.5 m SFP+ dedicated stack cables (need a license loaded, supported by the last 16 ports and used only for zero-configuration stacking)
10GE SFP+ optical port	SFP+	A 10GE SFP+ Ethernet optical port supports auto-sensing to 1000 Mbit/s. It sends and receives service data at 1000 Mbit/s or 10 Gbit/s.	GE eSFP optical modules GE-CWDM eSFP optical modules GE-DWDM eSFP optical modules GE SFP copper module 10GE SFP+ optical modules (OSXD22N00 not supported) 10GE-CWDM SFP+ optical modules 10GE-DWDM SFP+ optical modules 1 m, 3 m, 5 m, and 10 m SFP+ high-speed copper cables 3 m and 10 m SFP+ AOC cables 0.5 m and 1.5 m SFP+ dedicated stack cables (only for zero-configuration stacking and not supported after the speed of the first 48 GE ports is increased to 10GE)
Console port	RJ45	The console port is connected to a console for on-site configuration.	Console cable
ETH management port	RJ45	You can connect a switch to a configuration terminal or network management workstation through the ETH management port to configure the switch locally or remotely. You can choose to download the software package through the ETH management port in the BootLoad menu. File transfer through the ETH management port is faster than transfer through the console port.	Ethernet cable

Indicators and Buttons

Figure 4-697 Indicators on the S5736-S48S4X-A

Table 4-2020 Description of indicators on the switch

No.	Indicator	Name	Color	Status	Description
1	-	Service port indicator	Green	Off	The port is not connected or has been shut down.
			Green	Steady on	A link has been established on the port.
			Yellow	Off	The port is not sending or receiving data.
			Yellow	Blinking	The port is sending or receiving data.
2	PWR	Power module indicator	-	Off	The switch is powered off.
2	PWR	Power module indicator	Green	Steady on	The system power supply is normal.
3	SYS	System status indicator	-	Off	The system is not running.
			Green	Fast blinking	The system is starting.
			Green	Steady on	During the system startup preparation phase, the SYS indicator is steady green, which lasts for a maximum of 30 seconds.
			Green	Slow blinking	The system is running normally.
			Red	Steady on	The system does not work normally after registration, or a fan alarm or a temperature alarm has been generated.
4	MST	Stack indicator	-	Off	The switch is not the master switch in a stack.
4	MST	Stack indicator	Green	Blinking	The switch is the master switch in a stack or a standalone switch.
5	ID	ID indicator	-	Off	The ID indicator is not used (default state).
5	ID	ID indicator	Blue	Steady on	The indicator identifies the switch to maintain. The ID indicator can be turned on or off remotely to help field engineers find the switch to maintain.
6	L/A	ETH port indicator	-	Off	The ETH port is not connected.
			Green	Steady on	The ETH port is connected.
			Green	Blinking	The Eth port is sending or receiving data.

Power Supply System

The switch has a built-in AC power module and does not support pluggable power modules.

Heat Dissipation System

The switch has three built-in fans for forced air cooling. Air flows in from the left side and front panel, and exhausts from the right side.

Click to enlarge

This figure only shows the airflow direction and does not depict the actual device.

Technical Specifications

Table 4-2021 Technical specifications of the S5736-S48S4X-A

Item	Specification
Dimensions without packaging (H x W x D) [mm(in.)]	Basic dimensions (excluding the parts protruding from the body): 43.6 mm x 442.0 mm x 220.0 mm (1.72 in. x 17.4 in. x 8.66 in.) Maximum dimensions (the depth is the distance from ports on the front panel to the parts protruding from the rear panel): 43.6 mm x 442.0 mm x 228.0 mm (1.72 in. x 17.4 in. x 9.0 in.)
Dimensions with packaging (H x W x D) [mm(in.)]	90 mm × 555 mm × 345 mm (3.54 in. x 21.85 in. x 13.58 in.)
Chassis height [U]	1 U
Weight without packaging [kg(lb)]	3.6 kg (7.9 lb)
Weight with packaging [kg(lb)]	4.7 kg (10.36 lb)
Typical power consumption [W]	87 W
Typical heat dissipation [BTU/hour]	296.85 BTU/hour
Maximum power consumption [W]	111 W
Maximum heat dissipation [BTU/hour]	378.74 BTU/hour
Static power consumption [W]	39 W
MTBF [year]	41.97 year
MTTR [hour]	2 hour
Availability	>0.99999
Noise at normal temperature (acoustic power) [dB(A)]	56.8 dB(A)
Noise at normal temperature (acoustic pressure) [dB(A)]	44.8 dB(A)
Number of card slots	0
Number of power slots	0
Number of fans modules	3
Redundant power supply	Not supported
Long-term operating temperature [°C(°F)]	-5°C to +45°C (23°F to 113°F) at an altitude of 0-1800 m (0-5906 ft.)
Short-term operating temperature [°C(°F)]	-5°C to +50°C (23°F to 122°F) at an altitude of 0-1800 m (0-5906 ft.)
Restriction on the operating temperature variation rate [°C(°F)]	When the altitude is 1800-5000 m (5906-16404 ft.), the highest operating temperature reduces by 1°C (1.8°F) every time the altitude increases by 220 m (722 ft.). The equipment can operate beyond the normal operating temperature range for a short-term period, but the following conditions must be met: The equipment operates at a temperature of over 45°C (113°F) consecutively for at most 96 hours in one year. The equipment operates at a temperature of over 45°C (113°F) for a total of no more than 360 hours in one year. The equipment operates at a temperature of over 45°C (113°F) for no more in 15 times in one year. The equipment may be damaged or experience unexpected exceptions if any of the preceding limits is exceeded. The equipment cannot start when the temperature is lower than 0°C (32°F). The maximum distance of optical modules used in these conditions cannot exceed 10 km.
Storage temperature [°C(°F)]	-40°C to +70°C (-40°F to +158°F)
Long-term operating relative humidity [RH]	5% to 95%, noncondensing
Long-term operating altitude [m(ft.)]	0-5000 m (0-16404 ft.)
Storage altitude [m(ft.)]	0-5000 m (0-16404 ft.)
Power supply mode	AC built-in
Rated input voltage [V]	AC input: 100 V AC to 130 V AC, 200 V AC to 240 V AC, 50/60 Hz High-Voltage DC input: 240 V DC
Input voltage range [V]	AC input: 90 V AC to 290 V AC, 45 Hz to 65 Hz High-Voltage DC input: 190 V DC to 290 V DC
Maximum input current [A]	6.0 A
Memory	2 GB
Flash memory	1 GB in total. To view the available flash memory size, run the display version command.
Console port	RJ45
Eth Management port	RJ45
USB	Not supported
RTC	Supported
RPS input	Not supported
Service port surge protection [kV]	-
Power supply surge protection [kV]	±6 kV in differential mode, ±6 kV in common mode
Types of fans	Built-in
Heat dissipation mode	Heat dissipation with fan, intelligent fan speed adjustment
Airflow direction	Air intake from left and front, air exhaustion from right
PoE	Not supported
Certification	EMC certification Safety certification Manufacturing certification

Traducción

简体中文

Descargar

Updated: 2023-06-15

N.° del documento: EDOC1000013597

Vistas:4894559

Descargas: 43636

Average rating:

This Document Applies to these Products

Related Version

Documentos relacionados

Digital Signature File

Digital Signature Authentication Mode