S5700-28C-HI - S5700 Series Switches Hardware Description (V200)

S5700 Series Switches Hardware Description (V200)

Rate and give feedback:

Huawei ha traducido este documento a diferentes idiomas combinando la traducción automática con la revisión humana a fin de permitirle entender mejor su contenido. Nota: Sin importar lo avanzada que sea, la traducción automática no puede igualar la calidad que proporcionan los traductores profesionales. Huawei no asume ninguna responsabilidad por la precisión de las traducciones y recomienda consultar el documento escrito en inglés (al cual puede acceder mediante el enlace proporcionado).

S5700-28C-HI

Version Mapping

Table 4-985 lists the mapping between the S5700-28C-HI and software versions.

Table 4-985 Version mapping

Series	Model	Software Version
S5700-HI	S5700-28C-HI	V100R006C01 to V200R005C02 NOTE: This model does not match V200R003C02 or V200R003C10.

Appearance and Structure

Figure 4-391 S5700-28C-HI appearance

1	Power module slot 1 NOTE: Applicable power modules: W0PSA1701 (170 W AC Power Module) ES5M0PSD1700 (170 W DC Power Module)	2	Power module slot 2 NOTE: Applicable power modules: W0PSA1701 (170 W AC Power Module) ES5M0PSD1700 (170 W DC Power Module)
3	ESD jack NOTE: Before installing or maintaining a switch, wear an ESD wrist strap and insert the other end of the ESD wrist strap into this ESD jack.	4	One console port
5	One ETH management port	6	Front card slot NOTE: Card supported: ES5D00X2SA00 (2-Port GE SFP/10GE SFP+ Front Optical Interface Card) ES5D00X4SA00 (4-Port GE SFP/10GE SFP+ Front Optical Interface Card) ES5D00G4SC00 (4-Port GE SFP Front Optical Interface Card)
7	One USB port	8	Twenty-four 10/100/1000BASE-T ports
9	Ground screw NOTE: It is used with a ground cable. The switch has two ground screws, any of which can be used to install a ground cable.	10	Monitoring port NOTE: The monitoring port monitors the cabinet door, power module, battery power, and power supply of the air conditioner.

Port Description

10/100/1000BASE-T port

A 10/100/1000BASE-T Ethernet electrical port sends and receives service data at 10/100/1000 Mbit/s, and must use an Ethernet cable. Table 4-986 describes the attributes of a 10/100/1000BASE-T Ethernet electrical port.

Table 4-986 Attributes of a 10/100/1000BASE-T Ethernet electrical port

Attribute	Description
Connector type	RJ45
Standards compliance	IEEE802.3, IEEE802.3u, IEEE802.3ab
Working mode	10/100/1000 Mbit/s auto-sensing
Maximum transmission distance	100 m

Console port

The console port is connected to a console for on-site configuration. The port must use a console cable. The console port is used when a switch is powered on for the first time. For details about the attributes of a console port, see Table 4-987.

Table 4-987 Attributes of a console port

Attribute	Description
Connector type	RJ45
Standards compliance	RS-232
Working mode	Duplex Universal Asynchronous Receiver/Transmitter (UART)
Baud rate	9600 bit/s, 19200 bit/s, 38400 bit/s, 57600 bit/s, or 115200 bit/s Default value: 9600 bit/s

ETH management port

You can connect a switch to a configuration terminal or network management workstation through the ETH management port to configure the switch locally or remotely. The port must use an Ethernet cable. You can choose to download the software package through the ETH management port in the BootROM menu. File transfer through the ETH management port is faster than transfer through the console port. For details on how to use the ETH management port, see the Configuration Guide - Basic Configurations. Table 4-988 describes the attributes of an ETH management port.

Table 4-988 Attributes of an ETH management port

Attribute	Description
Connector type	RJ45
Standards compliance	IEEE802.3
Working mode	10/100 Mbit/s auto-sensing
Maximum transmission distance	100 m

USB port

The USB port can have a USB flash drive connected to upgrade the switch, or transfer configuration files or other files. The USB port can only connect to a USB flash drive that complies with USB 2.0.

USB flash drives from different vendors differ in model compatibility and drivers. If a USB flash drive cannot be used, try to replace it with another one from a mainstream vendor. Switches support a maximum of 128 GB USB flash drives.

Indicator Description

Figure 4-392 Indicators on the S5700-28C-HI

Table 4-989 Description of indicators on the switch

Number	Indicator/Button	Color	Description
1	PWR1: power supply indicator	-	Off: No power module is available in power module slot 1, or the switch has only one power module but the power module does not work normally.
		Green	Steady on: A power module is installed in power module slot 1 and is working normally.
		Red	Steady on: The switch has two power modules installed. Any of the following situations occurs in power module slot 1: A power module is available in this slot but its power switch is in the OFF position. A power module is available in this slot but it is not connected to a power source. The power module in power module slot 1 fails.
2	PWR2: power supply indicator	-	Off: No power module is available in power module slot 2, or the switch has only one power module but the power module does not work normally.
		Green	Steady on: A power module is installed in power module slot 2 and is working normally.
		Red	Steady on: The switch has two power modules installed. Any of the following situations occurs in power module slot 2: A power module is available in this slot but its power switch is in the OFF position. A power module is available in this slot but it is not connected to a power source. The power module in power module slot 2 fails.
3	SYS: system status indicator	-	Off: The system is not running.
		Green	Indicator states and meaning in V100R006 version: Steady on: The system is not operating properly or is starting. Slow blinking: The system is running normally. Fast blinking: The system is copying the system software and configuration file from a USB flash drive during a USB-based upgrade. Indicator states and meaning in V200R001 and later versions: Fast blinking: The system is starting or is copying the system software and configuration file from a USB flash drive during a USB-based upgrade. Slow blinking: The system is running normally.
		Yellow	Steady on: The system is performing self-check during startup (only applicable to V100R006). Blinking: The system has been successfully upgraded using a USB flash drive and the switch has restarted. You can remove the USB flash drive from the switch.
		Red	Steady on: The system does not work normally after registration, or a fan or temperature alarm has been generated. Blinking: An error occurred during USB-based upgrade and the system failed to be upgraded after a USB flash drive is inserted.
4	MODE: mode indicator	-	Off: The service port indicators are in the status mode (default). In the status mode, the service port indicator shows the port link or activity state.
		Green	Steady on: The service port indicators show the port speed. After 45 seconds, the service port indicators automatically restore to the status mode.
		Red	Steady on: The service port indicators show the stack ID of the switch. After 45 seconds, the service port indicators automatically restore to the status mode.
5	Mode switch button	-	In versions earlier than V200R003C00: When you press this button once, the mode indicator turns green and the service port indicators show the speed of each service port. When you press this button a second time, the mode indicator turns off. In V200R003C00 and later versions: When you press this button once, the mode indicator turns green and the service port indicators show the speed of ports. When you press this button a second time, the mode indicator turns red and the service port indicators show stack information. When you press this button a third time, the mode indicator turns off and the service port indicators restore to the status mode. If you do not press the button within 45 seconds, the mode indicator restores to the default mode.
6	Service port indicator	Meanings of service port indicators vary in different modes. For details, see Table 4-990 and Table 4-991.
7	ETH indicator	Green	Off: No link is established on the port. Steady on: The port is connected. Blinking: The port is sending or receiving data.

Table 4-990 Description of service port indicators in different modes (one indicator for each port)

Display Mode	Color	Status	Description
Status	-	Off	The port is not connected or has been shut down.
	Green	Steady on	A link has been established on the port.
	Green	Blinking	The port is sending or receiving data.
Speed	-	Off	The port is not connected or has been shut down.
	Green	Steady on	10M/100M/1000M port: The port is operating at 10/100 Mbit/s. 1000M/10GE port: The port is operating at 1000 Mbit/s.
	Green	Blinking	10M/100M/1000M port: The port is operating at 1000 Mbit/s. 1000M/10GE port: The port is operating at 10 Gbit/s.
Stack	-	Off	Port indicators do not show the stack ID of the switch.
	Green	Steady on	The switch is not the master switch in a stack. If the indicator of a port is steady on, the number of this port is the stack ID of the switch. If the indicators of ports 1 to 9 are steady on, the stack ID of the switch is 0.
	Green	Blinking	The switch is the master switch in a stack. If the indicator of a port is blinking, the number of this port is the stack ID of the switch. If the indicators of ports 1 to 9 are blinking, the stack ID of the switch is 0.

Table 4-991 Description of service port indicators in different modes (two indicators for each port)

Display Mode	Color	Status	Description
Status	-	Off	The port is not connected or has been shut down.
	Green	Steady on	A link has been established on the port.
	Yellow	Blinking	The port is sending or receiving data.
Speed	-	Off	The port is not connected or has been shut down.
	Green and yellow	Steady on	10M/100M/1000M port: The port is operating at 10/100 Mbit/s. 100M/1000M port: The port is operating at 100 Mbit/s.
	Green and yellow	Blinking	10M/100M/1000M port: The port is operating at 1000 Mbit/s. 100M/1000M port: The port is operating at 1000 Mbit/s.
Stack	-	Off	Port indicators do not show the stack ID of the switch.
	Green and yellow	Steady on	The switch is not the master switch in a stack. If the indicator of a port is steady on, the number of this port is the stack ID of the switch. If the indicators of ports 1 to 9 are steady on, the stack ID of the switch is 0.
	Green and yellow	Blinking	The switch is the master switch in a stack. If the indicator of a port is blinking, the number of this port is the stack ID of the switch. If the indicators of ports 1 to 9 are blinking, the stack ID of the switch is 0.

Power Supply Configuration

The S5700-28C-HI uses pluggable power modules. It can be configured with a single power module or double power modules for 1+1 power redundancy. Pluggable AC and DC power modules can be used together in the same switch.

Figure 4-393 shows the power supply connections of dual DC power modules. After DC power is transmitted to the PWR module, the PWR module provides 12 V output voltage, and the motherboard provides power for the entire device.

Figure 4-393 Power supply connections of dual DC power modules

NEG: negative wire

RTN: positive wire

GND: 12 V reference ground

Figure 4-394 shows the power supply connections of dual AC power modules. After AC power is transmitted to the PWR module, the PWR module provides 12 V output voltage, and the motherboard provides power for the entire device.

Figure 4-394 Power supply connections of dual AC power modules

L: Live wire

N: Neutral wire

PGND: Protection ground wire

GND: 12 V reference ground

Heat Dissipation

The S5700-28C-HI has three built-in fans for forced air cooling. The airflow direction is left-to-right.

Click to enlarge

This figure only shows the airflow direction and does not depict the actual device.

Technical Specifications

Table 4-992 lists technical specifications of the S5700-28C-HI.

Table 4-992 Technical specifications

Item	Description
Memory (RAM)	512 MB
Flash	64 MB
Mean time between failures (MTBF)	28.7 years when a 4-port 10GE interface card is configured, 41.1 years when a 2-port 10GE interface card is configured, 42.9 years when a 4-port GE interface card is configured
Mean time to repair (MTTR)	2 years
Availability	> 0.99999
Service port surge protection	±2 kV in common mode
Power supply surge protection	Using AC power modules: ±6 kV in differential mode, ±6 kV in common mode Using DC power modules: ±1 kV in differential mode, ±2 kV in common mode
Dimensions (H x W x D)	44.4 mm x 442.0 mm x 220.0 mm (1.75 in. x 17.4 in. x 8.7 in.)
Weight	Empty: ≤ 5 kg (11.02 lb) Fully configured: ≤ 6.5 kg (14.33 lb)
Stack ports	Versions earlier than V200R003C00 do not support stack ports. Since V200R003C00, 10GE ports on the front card can be used as stack ports.
RPS	Not supported
PoE	Not supported
Rated voltage range	100 V AC to 240 V AC, 50/60 Hz -48 V DC to -60 V DC
Maximum voltage range	90 V AC to 264 V AC, 47 Hz to 63 Hz -36 V DC to -72 V DC
Maximum power consumption (100% throughput, full speed of fans)	76.6 W
Operating temperature	-5°C to +55°C (23°F to 131°F) NOTE: The operating temperature of the switch is -5°C to +50°C (23°F to 122°F) when it uses SFP+ optical modules with 40 km or longer transmission distances.
Storage temperature	-40°C to +70°C (-40°F to +158°F)
Noise under normal temperature (27°C, sound power)	< 60 dB(A)
Relative humidity	5% to 95%, noncondensing
Operating altitude	AC power modules configured: 0-5000 m (0-16404 ft.) DC power modules configured: 0-2000 m (0-6562 ft.)
Certification	EMC certification Safety certification Manufacturing certification
Part number	02353630

Indicator Description

Traducción

简体中文

Descargar

Updated: 2023-06-15

N.° del documento: EDOC1000013597

Vistas:4893830

Descargas: 43634

Average rating:

This Document Applies to these Products

Related Version

Documentos relacionados

Digital Signature File

Digital Signature Authentication Mode