S5736-S24UM4XC (98011020) - S5700 Series Switches Hardware Description (V200)

S5700 Series Switches Hardware Description (V200)

Rate and give feedback:

Huawei ha traducido este documento a diferentes idiomas combinando la traducción automática con la revisión humana a fin de permitirle entender mejor su contenido. Nota: Sin importar lo avanzada que sea, la traducción automática no puede igualar la calidad que proporcionan los traductores profesionales. Huawei no asume ninguna responsabilidad por la precisión de las traducciones y recomienda consultar el documento escrito en inglés (al cual puede acceder mediante el enlace proporcionado).

S5736-S24UM4XC (98011020)

Overview

Table 4-2002 Basic information about the S5736-S24UM4XC

Item	Details
Description	S5736-S24UM4XC base (24100M/1G Ethernet ports, optional RTU upgrade to 2.5/5/10G, 410GE SFP+ ports, 1*expansion slot, PoE++, without power module)
Part Number	98011020
Model	S5736-S24UM4XC
First supported version	V200R020C00
Other part numbers	98011020-001: S5736-S24UM4XC 2.5&10G bundle (12100M/1G/2.5G Ethernet ports, 12100M/1G/2.5G/5G/10G Ethernet ports, optional RTU upgrade to 5/10G, 410GE SFP+ ports, 1expansion slot, PoE++, 11000W AC power) 98011020-004: S5736-S24UM4XC 10G bundle (24100M/1G/2.5G/5G/10G Ethernet ports, 410GE SFP+ ports, 1expansion slot, PoE++, 1*1000W AC power)

There are several S5736-S24UM4XC bundles, which consist of different power supplies and ports, as listed in Table 4-2003.

Table 4-2003 S5736-S24UM4XC bundles

Part Number	Description	Remarks
98011020	S5736-S24UM4XC Base(24100M/1G Ethernet ports,Optional RTU upgrade to 2.5/5/10G, 410GE SFP+ ports, 1*expansion slot, PoE++, without power module)	By default, no power supply is configured. By default, multi-GE ports support 100 Mbit/s and 1000 Mbit/s. You can purchase an RTU license to increase the port rate to 2.5 Gbit/s, 5 Gbit/s, or 10 Gbit/s. There is a label on the rear side of the device, which contains the default rate "24*GE" supported by the multi-GE ports.
98011020-001	S5736-S24UM4XC 2.5&10G Bundle(12100M/1G/2.5G Ethernet ports, 12100M/1G/2.5G/5G/10G Ethernet ports, Optional RTU upgrade to 5/10G, 410GE SFP+ ports, 1expansion slot, PoE++, 1*1000W AC power)	By default, one 1000 W AC power module is configured. By default, the first 12 multi-GE ports support 100 Mbit/s, 1000 Mbit/s, and 2.5 Gbit/s. You can purchase an RTU license to increase the port rate to 5 Gbit/s or 10 Gbit/s. By default, the last 12 multi-GE ports support 100 Mbit/s, 1000 Mbit/s, 2.5 Gbit/s, 5 Gbit/s, and 10 Gbit/s. There is a label on the rear side of the device, which contains the default rate "122.5GE+1210GE" supported by the multi-GE ports.
98011020-004	S5736-S24UM4XC 10G Bundle(24100M/1G/2.5G/5G/10G Ethernet ports, 410GE SFP+ ports, 1expansion slot, PoE++, 11000W AC power)	By default, one 1000 W AC power module is configured. By default, multi-GE ports support 100 Mbit/s, 1000 Mbit/s, 2.5 Gbit/s, 5 Gbit/s, and 10 Gbit/s. There is a label on the rear side of the device, which contains the default rate "24*10GE" supported by the multi-GE ports.

Part Number

Description

Remarks

98011020

S5736-S24UM4XC Base(24*100M/1G Ethernet ports,Optional RTU upgrade to 2.5/5/10G, 4*10GE SFP+ ports, 1*expansion slot, PoE++, without power module)

By default, no power supply is configured.

By default, multi-GE ports support 100 Mbit/s and 1000 Mbit/s. You can purchase an RTU license to increase the port rate to 2.5 Gbit/s, 5 Gbit/s, or 10 Gbit/s.

There is a label on the rear side of the device, which contains the default rate "24*GE" supported by the multi-GE ports.

98011020-001

S5736-S24UM4XC 2.5&10G Bundle(12*100M/1G/2.5G Ethernet ports, 12*100M/1G/2.5G/5G/10G Ethernet ports, Optional RTU upgrade to 5/10G, 4*10GE SFP+ ports, 1*expansion slot, PoE++, 1*1000W AC power)

By default, one 1000 W AC power module is configured.

By default, the first 12 multi-GE ports support 100 Mbit/s, 1000 Mbit/s, and 2.5 Gbit/s. You can purchase an RTU license to increase the port rate to 5 Gbit/s or 10 Gbit/s.

By default, the last 12 multi-GE ports support 100 Mbit/s, 1000 Mbit/s, 2.5 Gbit/s, 5 Gbit/s, and 10 Gbit/s.

There is a label on the rear side of the device, which contains the default rate "12*2.5GE+12*10GE" supported by the multi-GE ports.

98011020-004

S5736-S24UM4XC 10G Bundle(24*100M/1G/2.5G/5G/10G Ethernet ports, 4*10GE SFP+ ports, 1*expansion slot, PoE++, 1*1000W AC power)

By default, one 1000 W AC power module is configured.

By default, multi-GE ports support 100 Mbit/s, 1000 Mbit/s, 2.5 Gbit/s, 5 Gbit/s, and 10 Gbit/s.

There is a label on the rear side of the device, which contains the default rate "24*10GE" supported by the multi-GE ports.

A pre-configured or loaded RTU (right to use) license of a device is bound to the device ESN and cannot be unbound or transferred to other devices.

For details about the RTU licenses supported by the device and how to load them, see the License Usage Guide.

Components

Figure 4-691 S5736-S24UM4XC appearance

1	Twenty-four 100M/1000M/2.5GE/5GE/10GE BASE-T PoE++ ports (multi-GE ports)	2	Four 10GE SFP+ optical ports
3	One console port	4	One ETH management port
5	One USB port	6	One PNP button NOTICE: To restore the factory settings and reset the switch, hold down the button for at least 6 seconds. To reset the switch, press the button. Resetting the switch will cause service interruption. Exercise caution when you press the PNP button.
7	Ground screw NOTE: It is used with a ground cable.	8	Rear card slot NOTE: Applicable card: S7X08000 (02312URW) (applicable in V200R020C10 and later versions) S7X08000 (02312URW-002) (applicable in V200R021C10SPC600 and later versions) ES5D21Q02Q00 ES5D21Q04Q01 S7Q02001 (02313UBW) (applicable in V200R021C01 and later versions) S7Q02001 (02313UBW-002) (applicable in V200R021C10SPC600 and later versions)
9	Fan module slot 1 NOTE: Applicable fan module: FAN-023A-B (Fan box(B,FAN panel side exhaust))	10	Fan module slot 2 NOTE: Applicable fan module: FAN-023A-B (Fan box(B,FAN panel side exhaust))
11	Power module slot 1 NOTE: Applicable power module: PAC1000S56-CB (02312KND: 1000 W PoE AC&240 V DC Power Module) PAC1000S56-CB (02312KND-001: 1000 W PoE AC&240 V DC Power Module) PAC1000S56-DB (1000 W PoE AC&240 V DC Power Module) (applicable in V200R020C10 and later versions) PDC1000S56-CB (1000 W PoE DC Power Module) (applicable in V200R021C00 and later versions) PAC600S56-CB (600 W PoE AC&240 V DC Power Module (Back to Front, Power panel side exhaust)) (applicable in V200R021C10 and later versions)	12	Power module slot 2 NOTE: Applicable power module: PAC1000S56-CB (02312KND: 1000 W PoE AC&240 V DC Power Module) PAC1000S56-CB (02312KND-001: 1000 W PoE AC&240 V DC Power Module) PAC1000S56-DB (1000 W PoE AC&240 V DC Power Module) (applicable in V200R020C10 and later versions) PDC1000S56-CB (1000 W PoE DC Power Module) (applicable in V200R021C00 and later versions) PAC600S56-CB (600 W PoE AC&240 V DC Power Module (Back to Front, Power panel side exhaust)) (applicable in V200R021C10 and later versions)

Ports

Table 4-2004 lists the maximum transmission distances of different cables on multi-GE ports.

Table 4-2004 Maximum transmission distances of different cables on multi-GE ports

Cable Type (6-a-1 Bundle)	Multi-GE Port (Different Rates)
Cable Type (6-a-1 Bundle)	100M/1000M	2.5GE	5GE	10GE
Category 5e unshielded twisted pair (Cat5e UTP)	100 m	100 m	55 m 100 m (6-a-1 bundle only for the first 30 m) Not recommended due to high risk	Not supported
Category 5e shielded twisted pair (Cat5e STP)	100 m	100 m	100 m	Not supported
Category 6 unshielded twisted pair (Cat6 UTP)	100 m	100 m	100 m Not recommended due to high risk	Not supported
Category 6 shielded twisted pair (Cat6 STP)	100 m	100 m	100 m	Not supported
Category 6A unshielded twisted pair (Cat6A U/UTP)	100 m	100 m	100 m Not recommended due to high risk	Not supported
Category 6A foiled/unshielded twisted pair (Cat6A F/UTP)	100 m	100 m	100 m	100 m
Category 6A shielded twisted pair (Cat6A STP)	100 m	100 m	100 m	100 m
Category 7 twisted pair (Cat7)	100 m	100 m	100 m	100 m

6-a-1 stands for the six-around-one cable bundle mode, with one cable in the center and six cables bundled evenly around it.

If a port works at a rate of 5 Gbit/s, you are advised not to use unshielded Ethernet cables due to the following causes:

802.3bz requires that the ALSNR value for alien crosstalk between Ethernet cables be greater than 0, but the standards for Cat5e and Cat6 unshielded twisted pairs do not specify the required ALSNR value. Therefore, such cables may not meet the crosstalk requirement in 802.3bz, causing severe problems such as continuous packet loss or port flapping may occur.
According the cabling specification TIA TSB-5021, using Cat5e and Cat6 cables for 5G poses high risks.
Currently, no clear onsite testing or evaluation method is available for checking whether ALSNR of cables conforms to 802.3bz.

If a port works at a rate of 5 Gbit/s and a Cat6 shielded Ethernet cable is used, the Ethernet cable must comply with ISO 11801 PL Class E (+All) or TIA Cat 6 Channel (+All). If a Cat6A shielded Ethernet cable is used, the Ethernet cable must comply with ISO 11801 PL2 Class Ea (+All) or TIA Cat6A Channel (+All). Otherwise, serious problems such as continuous packet loss or interface flapping may occur.

If a port works at a rate of 10 Gbit/s and a Cat6A shielded Ethernet cable is used, the Ethernet cable must comply with ISO 11801 PL2 Class Ea (+All) or TIA Cat6A Channel (+All). Otherwise, serious problems such as continuous packet loss or interface flapping may occur.

If Cat5e and Cat6 unshielded twisted pairs do not meet the 5G requirement, you are advised to replace them with shielded twisted pairs or reduce the rate of ports to 2.5G.

If Cat5E, Cat6, or Cat6A unshielded twisted pairs are used on electrical ports working at 10 Gbit/s, severe problems such as continuous packet loss or port flapping may occur.

Table 4-2005 Ports on the S5736-S24UM4XC

Port	Connector Type	Description	Available Components
100M/1000M/2.5GE/5GE/10GE BASE-T PoE++ port (multi-GE port)	RJ45	A 100M/1000M/2.5GE/5GE/10GE BASE-T port (multi-GE port) sends and receives service data at 100 Mbit/s, 1 Gbit/s, 2.5 Gbit/s, 5 Gbit/s, or 10 Gbit/s. The port supports the PoE function.	If the 2.5 Gbit/s or 5 Gbit/s speed is required, the port must use an Ethernet cable of Cat5e or higher category. If the 10 Gbit/s speed is required, the port must use an Ethernet cable of Cat6A F/UTP or higher category.
10GE SFP+ optical port	SFP+	A 10GE SFP+ Ethernet optical port supports auto-sensing to 1000 Mbit/s. It sends and receives service data at 1000 Mbit/s or 10 Gbit/s.	GE eSFP optical modules GE-CWDM eSFP optical modules GE-DWDM eSFP optical modules GE SFP copper module 10GE SFP+ optical modules (OSXD22N00 not supported) 10GE-CWDM SFP+ optical modules 10GE-DWDM SFP+ optical modules 1 m, 3 m, 5 m, and 10 m SFP+ high-speed copper cables 3 m and 10 m SFP+ AOC cables 0.5 m and 1.5 m SFP+ dedicated stack cables (only for zero-configuration stacking)
Console port	RJ45	The console port is connected to a console for on-site configuration.	Console cable
ETH management port	RJ45	You can connect a switch to a configuration terminal or network management workstation through the ETH management port to configure the switch locally or remotely. You can choose to download the software package through the ETH management port in the BootLoad menu. File transfer through the ETH management port is faster than transfer through the console port.	Ethernet cable
USB port	USB 2.0 Type A	The USB port can have a USB flash drive connected to upgrade the switch, or transfer configuration files or other files. The USB port can only connect to a USB flash drive that complies with USB 2.0. USB flash drives from different vendors differ in model compatibility and drivers. If a USB flash drive cannot be used, try to replace it with another one from a mainstream vendor. Switches support a maximum of 128 GB USB flash drives.	USB flash drive

Indicators and Buttons

Figure 4-692 Indicators on the S5736-S24UM4XC

Table 4-2006 Description of indicators on the switch

No.	Indicator	Name	Color	Status	Description
1	PWR1	Power module indicator	-	Off	No power module is available in power module slot 1, or the switch has only one power module but the power module does not work normally.
			Green	Steady on	A power module is installed in power module slot 1 and is working normally.
			Yellow	Steady on	The switch has two power modules installed. Any of the following situations occurs in power module slot 1: A power module is available in this slot but it is not connected to a power source. The power module in this slot has failed.
2	PWR2	Power module indicator	-	Off	No power module is available in power module slot 2, or the switch has only one power module but the power module does not work normally.
			Green	Steady on	A power module is installed in power module slot 2 and is working normally.
			Yellow	Steady on	The switch has two power modules installed. Any of the following situations occurs in power module slot 2: A power module is available in this slot but it is not connected to a power source. The power module in this slot has failed.
3	SYS	System status indicator	-	Off	The system is not running.
			Green	Fast blinking	The system is starting.
			Green	Steady on	During the system startup preparation phase, the SYS indicator is steady green, which lasts for a maximum of 30 seconds.
			Green	Slow blinking	The system is running normally.
			Red	Steady on	The system does not work normally after registration, or a fan alarm or a temperature alarm has been generated.
4	MST	Stack indicator	-	Off	If you are not changing the indicator mode (default): The switch is a standby or slave switch in a stack or the stacking function is not enabled on the switch. If you are changing the indicator mode: The stack mode is not selected.
			Green	Steady on	The stack mode is selected. The switch is a standby or slave switch in a stack, and the service port indicators show the stack ID of the switch.
			Green	Blinking	If you are not changing the indicator mode (default): The switch is the master switch in a stack or a standalone switch with the stacking function enabled. If you are changing the indicator mode: The stack mode is selected. The switch is the master switch in a stack or a standalone switch, and the service port indicators show the stack ID of the master switch. After 45 seconds, the service port indicators automatically restore to the status mode.
5	SPEED	Speed indicator	-	Off	The speed mode is not selected.
5	SPEED	Speed indicator	Green	Steady on	The speed mode is selected, and service port indicators show the speed of each port.
6	PoE	PoE indicator	-	Off	The PoE mode is not selected.
6	PoE	PoE indicator	Green	Steady on	The PoE mode is selected, and service port indicators show the PoE status of each port.
7	MODE	Mode switch button	-	-	When you press this button once, the service port indicators change to the stack mode and show the stack ID of the local switch. When you press this button a second time, the service port indicators change to the speed mode and show the speed of each service port. When you press this button a third time, the service port indicators change to the PoE mode and show the PoE status of each service port. When you press this button a fourth time, the service port indicators restore to the default mode and show the connection status and link activity of each service port. If you do not press the MODE button within 45 seconds, the service port indicators restore to the default mode. In this case, the SPEED and PoE indicators are off. NOTE: Hold down the mode switch button for 6s and release it to start the web initial login mode. Either of the following situations will occur: If the switch has no configuration file, the system attempts to enter the web initial login mode. In this mode, the status of mode indicators is as follows: If the system enters the web initial login mode successfully, all mode indicators turn green and stay on for a maximum of 10 minutes. If the system fails to enter the initial login mode, all mode indicators fast blink for 10 seconds and then restore the default status. If the switch has a configuration file, the system cannot enter the web initial login mode. In this case, all mode indicators fast blink for 10s, and then return to the default states.
8	-	Service port indicator	Meanings of service port indicators vary in different modes. For details, see Table 4-2007.
9	ID	ID indicator	-	Off	The ID indicator is not used (default state).
9	ID	ID indicator	Blue	Steady on	The indicator identifies the switch to maintain. The ID indicator can be turned on or off remotely to help field engineers find the switch to maintain.
10	L/A	ETH port indicator	-	Off	The ETH port is not connected.
			Green	Steady on	The ETH port is connected.
			Green	Blinking	The ETH port is sending or receiving data.
11	USB	USB-based deployment indicator	-	Off	No USB flash drive is connected to the switch. The USB port is damaged. The indicator is damaged. The USB flash drive does not have any configuration file and cannot be used for deployment. The switch has been upgraded using the USB flash drive and is restarting.
			Green	Steady on	A USB-based deployment has been completed.
			Green	Blinking	The system is reading data from a USB flash drive.
			Yellow	Steady on	The switch has copied all the required files and completed the file check. The USB flash drive can be removed from the switch.
			Red	Blinking	An error has occurred when the system is executing the configuration file or reading data from the USB flash drive.

Table 4-2007 Description of service port indicators in different modes

Display Mode	Color	Status	Description
Default mode	-	Off	The port is not connected or has been shut down.
	Green	Steady on	A link has been established on the port.
	Green	Blinking	The port is sending or receiving data.
MST stack mode	Green	Off	Port indicators do not show the stack ID of the switch.
		Steady on	The switch is not the master switch in a stack. If the indicator of a port is steady on, the number of this port is the stack ID of the switch. If the indicators of ports 1 to 9 are steady on, the stack ID of the switch is 0.
		Blinking	The switch is the master switch in a stack. If the indicator of a port is blinking, the number of this port is the stack ID of the switch. If the indicators of ports 1 to 9 are blinking, the stack ID of the switch is 0.
Speed mode	-	Off	The port is not connected or has been shut down.
	Green	Steady on	100M/1000M/2.5GE/5GE/10GE BASE-T port: The port is operating at 100 Mbit/s or 1000 Mbit/s. 1000M/10GE SFP+ port: The port is operating at 1000 Mbit/s.
	Green	Blinking	100M/1000M/2.5GE/5GE/10GE BASE-T port: The port is operating at 2.5 Gbit/s, 5 Gbit/s, or 10 Gbit/s. 1000M/10GE SFP+ port: The port is operating at 10 Gbit/s.
PoE mode	-	Off	The port is not providing power to a powered device (PD).
	Green	Steady on	The port is providing power to a PD.
	Yellow	Steady on	The PoE function is disabled on the port.
	Yellow	Blinking	The port stops providing PoE power because of an exception (for example, an incompatible PD is connected to the port).
	Green and yellow	Blinking green and yellow alternately	The port fails to supply power to a PD due to one of the following reasons: The power required by the connected PD exceeds the maximum power or the configured power threshold of the port. The total power consumption of PDs has reached the maximum power of the switch. The manual power management mode is used and the port is not enabled to provide power to the PD.

Power Supply System

The switch is a PoE switch and supports two power module slots, each of which can have a 1000 W PoE or 600 W PoE power module installed. Pluggable AC and DC PoE power modules can be used together in the same switch.

Table 4-2008 Power supply configurations

Power Module 1	Power Module 2	Available PoE Power	Maximum Number of Ports (Fully Loaded)
1000 W AC (220 V) 1000 W DC	–	841 W	802.3af (15.4 W per port): 24 802.3at (30 W per port): 24 802.3bt (60 W per port): 14 802.3bt (90 W per port): 9
1000 W AC (110 V)	–	746 W	802.3af (15.4 W per port): 24 802.3at (30 W per port): 24 802.3bt (60 W per port): 12 802.3bt (90 W per port): 8
1000 W AC (220 V) 1000 W DC	1000 W AC (220 V) 1000 W DC	1791 W	802.3af (15.4 W per port): 24 802.3at (30 W per port): 24 802.3bt (60 W per port): 24 802.3bt (90 W per port): 19
1000 W AC (110 V) 1000 W DC	1000 W AC (110 V)	1601 W	802.3af (15.4 W per port): 24 802.3at (30 W per port): 24 802.3bt (60 W per port): 24 802.3bt (90 W per port): 17
600 W AC (220 V)	–	461 W	802.3af (15.4 W per port): 24 802.3at (30 W per port): 15 802.3bt (60 W per port): 7 802.3bt (90 W per port): 5
600 W AC (110 V)	–	176 W	802.3af (15.4 W per port): 11 802.3at (30 W per port): 5 802.3bt (60 W per port): 2 802.3bt (90 W per port): 1
600 W AC (220 V)	600 W AC (220 V)	1031 W	802.3af (15.4 W per port): 24 802.3at (30 W per port): 24 802.3bt (60 W per port): 17 802.3bt (90 W per port): 11
600 W AC (110 V)	600 W AC (110 V)	461 W	802.3af (15.4 W per port): 24 802.3at (30 W per port): 15 802.3bt (60 W per port): 7 802.3bt (90 W per port): 5
1000 W AC (220 V) 1000 W DC	600 W AC (220 V)	1411 W	802.3af (15.4 W per port): 24 802.3at (30 W per port): 24 802.3bt (60 W per port): 23 802.3bt (90 W per port): 15

When a switch has two power modules installed, the two power modules work in redundancy mode to provide power for the chassis and in load balancing mode to provide power for PDs.

Heat Dissipation System

The switch uses pluggable fan modules for forced air cooling. Air flows in from the left, right, and front sides, and exhausts from the rear panel.

Click to enlarge

This figure only shows the airflow direction and does not depict the actual device.

Technical Specifications

Table 4-2009 Technical specifications of the S5736-S24UM4XC

Item	Specification
Dimensions without packaging (H x W x D) [mm(in.)]	Basic dimensions (excluding the parts protruding from the body): 43.6 mm x 442.0 mm x 420.0 mm (1.72 in. x 17.40 in. x 16.54 in.) Maximum dimensions (the depth is the distance from ports on the front panel to the parts protruding from the rear panel): 43.6 mm x 442.0 mm x 448.0 mm (1.72 in. x 17.40 in. x 17.64 in.)
Dimensions with packaging (H x W x D) [mm(in.)]	150mm × 710mm × 560mm (5.90 in. x 27.95 in. x 22.05 in.)
Chassis height [U]	1 U
Weight without packaging [kg(lb)]	6.7 kg (14.77 lb)
Weight with packaging [kg(lb)]	9.7 kg (21.39 lb)
Typical power consumption [W]	117 W
Typical heat dissipation [BTU/hour]	399.22 BTU/hour
Maximum power consumption [W]	Without PoE: 176 W (without cards) Full PoE load: 1967 W (PoE: 1791 W, without cards)
Maximum heat dissipation [BTU/hour]	Without PoE: 600.53 (without cards) Full PoE load: 6711.60 (without cards)
Static power consumption [W]	71 W
MTBF [year]	59.44 year
MTTR [hour]	2 hour
Availability	>0.99999
Noise at normal temperature (acoustic power) [dB(A)]	70.1 dB(A)
Noise at normal temperature (acoustic pressure) [dB(A)]	58.1 dB(A)
Number of card slots	1
Number of power slots	2
Number of fans modules	2
Redundant power supply	1+1 Pluggable AC and DC power modules can be used together in the same switch.
Long-term operating temperature [°C(°F)]	-5°C to +45°C (23°F to 113°F) at an altitude of 0-1800 m (0-5906 ft.)
Short-term operating temperature [°C(°F)]	-5°C to +50°C (23°F to 122°F) at an altitude of 0-1800 m (0-5906 ft.)
Restriction on the operating temperature variation rate [°C(°F)]	When the altitude is 1800-5000 m (5906-16404 ft.), the highest operating temperature reduces by 1°C (1.8°F) every time the altitude increases by 220 m (722 ft.). The device can work for a short period of time when the operating temperature is beyond the normal range, but the following conditions must be met: The operating temperature can exceed 45°C (113°F) for a maximum of 96 consecutive hours in a year. The total time when the operating temperature exceeds 45°C (113°F) in a year is less than or equal to 360 hours. The number of times the operating temperature exceeds 45°C (113°F) is less than or equal to 15 in one year. If any of the preceding conditions is not met, the device may be damaged or an unknown error may occur. Devices cannot start when the temperature is lower than 0°C (32°F). The maximum transmission distance of an optical module used for short-term operation cannot exceed 10 km.
Storage temperature [°C(°F)]	-40°C to +70°C (-40°F to +158°F)
Long-term operating relative humidity [RH]	5% to 95%, noncondensing
Long-term operating altitude [m(ft.)]	0-5000 m (0-16404 ft.)
Storage altitude [m(ft.)]	0-5000 m (0-16404 ft.)
Power supply mode	Pluggable power supply
Rated input voltage [V]	AC input: 100 V AC to 130 V AC, 200 V AC to 240 V AC; 50/60 Hz High-voltage DC input: 240 V DC DC input: –48 V DC to –60 V DC
Input voltage range [V]	AC input: 90 V AC to 290 V AC; 45 Hz to 65 Hz High-voltage DC input: 190 V DC to 290 V DC DC input: –38.4 V DC to –72 V DC
Maximum input current [A]	The current specifications are related to the pluggable power module. For details, see Pluggable Power Modules.
Memory	2 GB
Flash memory	1 GB in total. To view the available flash memory size, run the display version command.
Console port	RJ45
Eth Management port	RJ45
USB	Supported
RTC	Supported
RPS input	Not supported
Service port surge protection [kV]	Common mode: ±6 kV
Power supply surge protection [kV]	Configured with AC power modules: ±6 kV in differential mode and ±6 kV in common mode Configured with DC power modules: ±2 kV in differential mode and ±4 kV in common mode
Types of fans	Pluggable
Heat dissipation mode	Heat dissipation with fan, intelligent fan speed adjustment
Airflow direction	Air intake from left,front and right, air exhaustion from behind
PoE	Supported
Certification	EMC certification Safety certification Manufacturing certification

Traducción

简体中文

Descargar

Updated: 2023-06-15

N.° del documento: EDOC1000013597

Vistas:4893495

Descargas: 43634

Average rating:

This Document Applies to these Products

Related Version

Documentos relacionados

Digital Signature File

Digital Signature Authentication Mode