S5731-H24P4XC (02352QPV/02352QPV-001/02352QPV-003) - S5700 Series Switches Hardware Description (V200)

S5700 Series Switches Hardware Description (V200)

Rate and give feedback:

Huawei ha traducido este documento a diferentes idiomas combinando la traducción automática con la revisión humana a fin de permitirle entender mejor su contenido. Nota: Sin importar lo avanzada que sea, la traducción automática no puede igualar la calidad que proporcionan los traductores profesionales. Huawei no asume ninguna responsabilidad por la precisión de las traducciones y recomienda consultar el documento escrito en inglés (al cual puede acceder mediante el enlace proporcionado).

S5731-H24P4XC (02352QPV/02352QPV-001/02352QPV-003)

Version Mapping

Table 4-1393 lists the mapping between the S5731-H24P4XC chassis and software versions.

Table 4-1393 Version mapping

Series	Model	Software Version
S5731-H	S5731-H24P4XC	02352QPV: V200R013C02 and later versions 02352QPV-001: V200R020C10 and later versions 02352QPV-003: V200R021C10SPC600 and later versions (If V200R021C10SPC500 is used, install V200R021HP0121 or a later patch. If V200R021C00SPC100 is used, install V200R021SPH013 or a later patch.)

Series

Model

Software Version

S5731-H

S5731-H24P4XC

02352QPV: V200R013C02 and later versions

02352QPV-001: V200R020C10 and later versions

02352QPV-003: V200R021C10SPC600 and later versions (If V200R021C10SPC500 is used, install V200R021HP0121 or a later patch. If V200R021C00SPC100 is used, install V200R021SPH013 or a later patch.)

Appearance and Structure

Figure 4-545 S5731-H24P4XC (02352QPV) appearance

Figure 4-546 S5731-H24P4XC (02352QPV-001/02352QPV-003) appearance

1	Twenty-four PoE+ 10/100/1000BASE-T ports	2	Four 10GE SFP+ ports Applicable modules and cables: GE optical module GE-CWDM optical module GE-DWDM optical module GE copper module (100M/1000M auto-sensing) 10GE SFP+ optical module (OSXD22N00 not supported) 10GE-CWDM optical module 10GE-DWDM optical module 1 m, 3 m, 5 m, and 10 m SFP+ high-speed copper cables 3 m and 10 m SFP+ AOC cables 0.5 m and 1.5 m SFP+ dedicated stack copper cables (used for zero-configuration stacking)
3	One console port	4	One ETH management port
5	One USB port	6	One PNP button NOTICE: To restore the factory settings and reset the switch, hold down the button for at least 6 seconds. To reset the switch, press the button. Resetting the switch will cause service interruption. Exercise caution when you press the PNP button.
7	Ground screw NOTE: It is used with a ground cable.	8	Rear card slot NOTE: Applicable card: ES5D21X08T00 ES5D21Q02Q00 S7X08000 (02312URW) (applicable in V200R019C10 and later versions) S7X08000 (02312URW-002) (applicable in V200R021C10SPC600 and later versions) S7Q02001 (02313UBW) (applicable in V200R021C01 and later versions) S7Q02001 (02313UBW-002) (applicable in V200R021C10SPC600 and later versions)
9	Fan module slot 1 NOTE: Applicable fan module: FAN-023A-B (Fan box(B,FAN panel side exhaust))	10	Fan module slot 2 NOTE: Applicable fan module: FAN-023A-B (Fan box(B,FAN panel side exhaust))
11	Power module slot 1 NOTE: Applicable power module: PAC1000S56-CB (02312KND: 1000 W PoE AC&240 V DC Power Module) PAC1000S56-CB (02312KND-001: 1000 W PoE AC&240 V DC Power Module) (applicable in V200R019C10 and later versions) PAC1000S56-DB (1000 W PoE AC&240 V DC Power Module) (applicable in V200R020C10 and later versions) PDC1000S56-CB (1000 W PoE DC Power Module) (applicable in V200R021C00 and later versions) PAC600S56-CB (600 W PoE AC&240 V DC Power Module (Back to Front, Power panel side exhaust)) (applicable in V200R021C10 and later versions)	12	Power module slot 2 NOTE: Applicable power module: PAC1000S56-CB (02312KND: 1000 W PoE AC&240 V DC Power Module) PAC1000S56-CB (02312KND-001: 1000 W PoE AC&240 V DC Power Module) (applicable in V200R019C10 and later versions) PAC1000S56-DB (1000 W PoE AC&240 V DC Power Module) (applicable in V200R020C10 and later versions) PDC1000S56-CB (1000 W PoE DC Power Module) (applicable in V200R021C00 and later versions) PAC600S56-CB (600 W PoE AC&240 V DC Power Module (Back to Front, Power panel side exhaust)) (applicable in V200R021C10 and later versions)

Port Description

10/100/1000BASE-T port

A 10/100/1000BASE-T Ethernet electrical port sends and receives service data at 10/100/1000 Mbit/s, and must use an Ethernet cable. Table 4-1394 describes the attributes of a 10/100/1000BASE-T Ethernet electrical port.

Table 4-1394 Attributes of a 10/100/1000BASE-T Ethernet electrical port

Attribute	Description
Connector type	RJ45
Standards compliance	IEEE802.3, IEEE802.3u, IEEE802.3ab
Working mode	10/100/1000 Mbit/s auto-sensing
Maximum transmission distance	100 m

10GE SFP+ optical port

A 10GE SFP+ Ethernet optical port supports auto-sensing to 1000 Mbit/s. It sends and receives service data at 1000 Mbit/s or 10 Gbit/s. Table 4-1395 describes the attributes of a 10GE SFP+ Ethernet optical port.

Table 4-1395 Attributes of a 10GE SFP+ port

Attribute	Description
Connector type	LC/PC
Optical port attributes	Depend on the optical module used
Standards compliance	IEEE802.3ae
Working mode	GE/10GE auto-sensing

Console port

The console port is connected to a console for on-site configuration. The port must use a console cable. The console port is used when a switch is powered on for the first time. For details about the attributes of a console port, see Table 4-1396.

Table 4-1396 Attributes of a console port

Attribute	Description
Connector type	RJ45
Standards compliance	RS-232
Working mode	Duplex Universal Asynchronous Receiver/Transmitter (UART)
Baud rate	9600 bit/s, 19200 bit/s, 38400 bit/s, 57600 bit/s, or 115200 bit/s Default value: 9600 bit/s

ETH management port

You can connect a switch to a configuration terminal or network management workstation through the ETH management port to configure the switch locally or remotely. The port must use an Ethernet cable. You can choose to download the software package through the ETH management port in the BootLoad menu. File transfer through the ETH management port is faster than transfer through the console port. Table 4-1397 describes the attributes of an ETH management port.

Table 4-1397 Attributes of an ETH management port

Attribute	Description
Connector type	RJ45
Standards compliance	IEEE802.3
Working Mode	10/100 Mbit/s auto-sensing
Maximum transmission distance	100 m

In V200R012C00 and later versions, you can log in to the switch that contains the ETH management port for the first time through the ETH port. For details, see "First Login to a Switch" in the Configuration Guide - Basic Configuration. If you have logged in to the switch for the first time by pressing and holding the MODE button for 6 seconds or longer and saved the configuration, the default configuration on the ETH port will be cleared. In this case, you cannot log in to the switch for the first time through the ETH port. You are advised to log in to the switch for the first time through the ETH port.

USB port

The USB port can have a USB flash drive connected to upgrade the switch, or transfer configuration files or other files. The USB port can only connect to a USB flash drive that complies with USB 2.0.

USB flash drives from different vendors differ in model compatibility and drivers. If a USB flash drive cannot be used, try to replace it with another one from a mainstream vendor. Switches support a maximum of 128 GB USB flash drives.

Indicator Description

The S5731-H24P4XC has the same types of indicators as the S5731-H48P4XC. For details, see Indicator Description.

Power Supply Configuration

The switch is a PoE switch and supports two power module slots, each of which can have a 1000 W PoE or 600 W PoE power module installed. Pluggable AC and DC PoE power modules can be used together in the same switch.

Table 4-1398 Power supply configurations

Power Module 1	Power Module 2	Available PoE Power	Maximum Number of Ports (Fully Loaded)
1000 W AC (220 V) 1000 W DC	–	760 W	802.3af (15.4 W per port): 24 802.3at (30 W per port): 24
1000 W AC (110 V)	–	665 W	802.3af (15.4 W per port): 24 802.3at (30 W per port): 22
1000 W AC (220 V) 1000 W DC	1000 W AC (220 V) 1000 W DC	1600 W	802.3af (15.4 W per port): 24 802.3at (30 W per port): 24
1000 W AC (110 V) 1000 W DC	1000 W AC (110 V)	Versions earlier than V200R021C10: 1330 W V200R021C10 and later versions: 1520 W	802.3af (15.4 W per port): 24 802.3at (30 W per port): 24
600 W AC (220 V)	–	380 W	802.3af (15.4 W per port): 24 802.3at (30 W per port): 12
600 W AC (110 V)	–	95 W	802.3af (15.4 W per port): 6 802.3at (30 W per port): 3
600 W AC (220 V)	600 W AC (220 V)	950 W	802.3af (15.4 W per port): 24 802.3at (30 W per port): 24
600 W AC (110 V)	600 W AC (110 V)	380 W	802.3af (15.4 W per port): 24 802.3at (30 W per port): 12
1000 W AC (220 V) 1000 W DC	600 W AC (220 V)	1330 W	802.3af (15.4 W per port): 24 802.3at (30 W per port): 24

When a switch has two power modules installed, the two power modules work in redundancy mode to provide power for the chassis and in load balancing mode to provide power for PDs.

Heat Dissipation

The S5731-H24P4XC uses pluggable fan modules for forced air cooling. Air flows in from the front side and exhausts from the rear panel.

This figure only shows the airflow direction and does not depict the actual device.

Technical Specifications

Table 4-1399 lists technical specifications of the S5731-H24P4XC.

Table 4-1399 Technical specifications

Item	Description
Memory (RAM)	4 GB
Flash	1 GB in total. To view the available flash memory size, run the display version command.
Mean time between failures (MTBF)	57.21 years
Mean time to repair (MTTR)	2 hours
Availability	> 0.99999
Service port surge protection	Common mode: ±6 kV
Power supply surge protection	Using AC power modules: ±6 kV in differential mode, ±6 kV in common mode Using DC power modules: ±2 kV in differential mode, ±4 kV in common mode
Dimensions (H x W x D)	Basic dimensions (excluding the parts protruding from the body): 43.6 mm x 442.0 mm x 420.0 mm (1.72 in. x 17.4 in. x 16.5 in.) Maximum dimensions (the depth is the distance from ports on the front panel to the handle on the rear panel): 43.6 mm x 442.0 mm x 448.0 mm (1.72 in. x 17.4 in. x 17.7 in.)
Weight (with packaging)	8.6 kg (18.96 lb)
Stack ports	10GE SFP+ ports on the front panel, or ports on the rear card
RTC	Supported
RPS	Not supported
PoE	Supported
Rated voltage range	AC input: 100 V AC to 130 V AC, 200 V AC to 240 V AC, 50/60 Hz High-Voltage DC input: 240 V DC DC input: -48 V DC to -60 V DC
Maximum voltage range	AC input: 90 V AC to 290 V AC, 45 Hz to 65 Hz High-Voltage DC input: 190 V DC to 290 V DC DC input: -38.4 V DC to -72 V DC
Maximum power consumption (100% throughput, full speed of fans)	Not providing the PoE function: 121 W (without card) 100% PoE loads: 977 W (PoE: 720 W, without card)
Typical power consumption (30% of traffic load, tested according to ATIS standard)	95 W (without card)
Operating temperature	-5°C to +45°C (23°F to 113°F) at an altitude of 0-1800 m (0-5906 ft.) NOTE: When the altitude is 1800-5000 m (5906-16404 ft.), the highest operating temperature reduces by 1°C (1.8°F) every time the altitude increases by 220 m (722 ft.). The switch cannot be started when the ambient temperature is lower than 0°C (32°F).
Storage temperature	-40°C to +70°C (-40°F to +158°F)
Noise under normal temperature (27°C, sound power)	< 62.3 dB(A)
Relative humidity	5% to 95%, noncondensing
Operating altitude	0-5000 m (0-16404 ft.)
Certification	EMC certification Safety certification Manufacturing certification
Part number	02352QPV 02352QPV-001 02352QPV-003

Traducción

简体中文

Descargar

Updated: 2023-04-21

N.° del documento: EDOC1000013597

Vistas:4292551

Descargas: 41234

Average rating:

This Document Applies to these Products

Related Version

Documentos relacionados

Digital Signature File

Digital Signature Authentication Mode