S5700-28C-PWR-SI - S5700 Series Switches Hardware Description (V200)

S5700 Series Switches Hardware Description (V200)

Rate and give feedback:

Huawei ha traducido este documento a diferentes idiomas combinando la traducción automática con la revisión humana a fin de permitirle entender mejor su contenido. Nota: Sin importar lo avanzada que sea, la traducción automática no puede igualar la calidad que proporcionan los traductores profesionales. Huawei no asume ninguna responsabilidad por la precisión de las traducciones y recomienda consultar el documento escrito en inglés (al cual puede acceder mediante el enlace proporcionado).

S5700-28C-PWR-SI

Version Mapping

Table 4-461 lists the mapping between the S5700-28C-PWR-SI and software versions.

Table 4-461 Version mapping

Series	Model	Software Version
S5700-SI	S5700-28C-PWR-SI	V200R001C00 to V200R005C02 NOTE: This model does not match V200R001C01, V200R003C02, V200R003C10, or V200R005C01.

Appearance and Structure

Figure 4-174 S5700-28C-PWR-SI appearance

1	Twenty PoE+ 10/100/1000BASE-T ports	2	Four combo ports (10/100/1000BASE-T (PoE+) + 100/1000BASE-X) Modules applicable to combo optical ports: FE optical module GE optical module GE-CWDM optical module
3	One console port	4	One ETH management port
5	One USB port	6	Front card slot NOTE: Card supported: ES5D00G4SA01 (4-Port GE SFP Front Optical Interface Card) ES5D000X2S00 (2-Port 10GE SFP+ Front Optical Interface Card) ES5D000X4S01 (4-Port 10GE SFP+ Front Optical Interface Card)
7	ESD jack NOTE: Before installing or maintaining a switch, wear an ESD wrist strap and insert the other end of the ESD wrist strap into this ESD jack.	8	Rear card slot NOTE: Card supported: ES5D00ETPC00 (Stack Rear Card) ES5D00ETPB00 (Extended Rear Card)
9	Fan slot NOTE: Applicable fan module: CX7E1FANA fan module	10	Power module slot 2 NOTE: Applicable power modules: 250 W AC PoE power module 500 W AC PoE power module
11	Power module slot 1 NOTE: Applicable power modules: 250 W AC PoE power module 500 W AC PoE power module	-	-

Port Description

10/100/1000BASE-T port

A 10/100/1000BASE-T Ethernet electrical port sends and receives service data at 10/100/1000 Mbit/s, and must use an Ethernet cable. Table 4-462 describes the attributes of a 10/100/1000BASE-T Ethernet electrical port.

Table 4-462 Attributes of a 10/100/1000BASE-T Ethernet electrical port

Attribute	Description
Connector type	RJ45
Standards compliance	IEEE802.3, IEEE802.3u, IEEE802.3ab
Working mode	10/100/1000 Mbit/s auto-sensing
Maximum transmission distance	100 m

Combo port

A combo port refers to a pair of ports consisting of an optical Ethernet port and an electrical Ethernet port on the panel. Each combo port matches only one internal forwarding port. A combo port can be configured as an electrical port or an optical port, but only one port can be active at a time. When one port is active, the other port is shut down.

By default, a combo port works in auto mode, in which the port type is determined as follows:

If the optical port has no optical module installed and the electrical port has no Ethernet cable connected, the port type depends on which port is connected first. If the electrical port is connected by an Ethernet cable first, the electrical port is used for data switching. If the optical port has an optical module installed first, the optical port is used for data switching.
If the electrical port has an Ethernet cable connected and is in Up state, the electrical port is still used for data switching when the optical port has an optical module installed.
If the optical port, no matter in Up or Down state, has an optical module installed, the optical port is still used for data switching when the electrical port has an Ethernet cable connected.
If the optical port has an optical module installed and the electrical port has an Ethernet cable connected, the optical port is used for data switching after the switch restarts.

You can configure a combo port as an electrical or optical port using the combo-port command.

Console port

The console port is connected to a console for on-site configuration. The port must use a console cable. The console port is used when a switch is powered on for the first time. For details about the attributes of a console port, see Table 4-463.

Table 4-463 Attributes of a console port

Attribute	Description
Connector type	RJ45
Standards compliance	RS-232
Working mode	Duplex Universal Asynchronous Receiver/Transmitter (UART)
Baud rate	9600 bit/s, 19200 bit/s, 38400 bit/s, 57600 bit/s, or 115200 bit/s Default value: 9600 bit/s

ETH management port

You can connect a switch to a configuration terminal or network management workstation through the ETH management port to configure the switch locally or remotely. The port must use an Ethernet cable. You can choose to download the software package through the ETH management port in the BootROM menu. File transfer through the ETH management port is faster than transfer through the console port. For details on how to use the ETH management port, see the Configuration Guide - Basic Configurations. Table 4-464 describes the attributes of an ETH management port.

Table 4-464 Attributes of an ETH management port

Attribute	Description
Connector type	RJ45
Standards compliance	IEEE802.3
Working mode	10/100 Mbit/s auto-sensing
Maximum transmission distance	100 m

USB port

The USB port can have a USB flash drive connected to upgrade the switch, or transfer configuration files or other files. The USB flash drive used on a switch must comply with USB 1.1.

USB flash drives from different vendors differ in model compatibility and drivers. If a USB flash drive cannot be used, try to replace it with another one from a mainstream vendor. Switches support a maximum of 128 GB USB flash drives.

Indicator Description

Figure 4-175 Indicators on the S5700-28C-PWR-SI

Table 4-465 Description of indicators on the switch

Number	Indicator/Button	Color	Description
1	PWR1: power supply indicator	-	Off: No power module is available in power module slot 1, or the power module is faulty when a single power module is configured.
		Green	Steady on: The power module in power module slot 1 is working properly.
		Red	Steady on: The switch has two power modules installed. Any of the following situations occurs in power module slot 1: A power module is available in this slot but its power switch is in the OFF position. The power module in power module slot 1 is available but is not connected to a power source. The system power and PoE power are faulty.
		Yellow	Steady on: If a single power module is installed, the PoE power is out of range. If dual power modules are installed, the system power or PoE power is out of range.
2	PWR2: power supply indicator	-	Off: No power module is available in power module slot 2, or the power module is faulty when a single power module is configured.
		Green	Steady on: The power module in power module slot 2 is working properly.
		Red	Steady on: The switch has two power modules installed. Any of the following situations occurs in power module slot 2: A power module is available in this slot but its power switch is in the OFF position. A power module is available in this slot but it is not connected to a power source. The system power and PoE power are faulty.
		Yellow	Steady on: If a single power module is installed, the PoE power is out of range. If dual power modules are installed, the system power or PoE power is out of range.
3	SYS: system status indicator	-	Off: The system is not running.
		Green	Steady on: The system is not operating properly or is starting. Slow blinking: The system is running normally. Fast blinking: The system is copying the system software and configuration file from a USB flash drive.
		Yellow	Steady on: The system is performing self-check during startup. Blinking: The system has been successfully upgraded using a USB flash drive and the switch has restarted. You can remove the USB flash drive from the switch.
		Red	Steady on: The system does not work normally after registration, or a fan or temperature alarm has been generated. Blinking: The system cannot be upgraded after a USB flash drive is inserted. The USB-based upgrade failed.
4	Mode indicator	-	Off: The service port indicators are in the status mode (default). In the status mode, the service port indicator shows the port link or activity state.
		Green	Steady on: The service port indicators show the port speed. After 45 seconds, the service port indicators automatically restore to the status mode.
		Red	Steady on: The service port indicators show the stack ID of the switch. After 45 seconds, the service port indicators automatically restore to the status mode.
		Yellow	Steady on: The service port indicators show the PoE status. After 45 seconds, the service port indicators automatically restore to the status mode.
5	Mode switch button	-	When you press this button once, the mode indicator turns green and the service port indicators show the speed of each service port. When you press this button a second time, the mode indicator turns red and the service port indicators show the stack status. When you press this button a third time, the mode indicator turns yellow and the service port indicators show the PoE status. When you press this button a fourth time, the mode indicator turns off. If you do not press the button within 45 seconds, the mode indicator restores to status mode.
6	Service port indicator	Meanings of service port indicators vary in different modes. For details, see Table 4-466.
7	ETH indicator	-	Off: No link is established on the port.
		Green	Steady on: The port is connected.
		Yellow	Blinking: The port is sending or receiving data.

Table 4-466 Description of service port indicators in different modes

Display Mode	Color	Description
Status	Green	Off: The port is not connected or has been shut down. Steady on: The port is connected. Blinking: The port is sending or receiving data.
Speed	Green	Off: The port is not connected or has been shut down. Steady on: 10M/100M/1000M port: The port is operating at 10/100 Mbit/s. 1000M/10GE port: The port is operating at 1000 Mbit/s. Blinking: 10M/100M/1000M port: The port is operating at 1000 Mbit/s. 1000M/10GE port: The port is operating at 10 Gbit/s.
PoE	Green	Off: The port does not provide PoE power. Steady on: The port is providing PoE power. Blinking: The PD connected to the port is not a standard PD or its power exceeds the maximum power or power threshold of the port.
Stack	Green	Off: The STCK mode is not selected. If the indicator is steady on, the switch is not a master switch: If the indicator of a port is steady on, the number of this port is the stack ID of the switch. If the indicators of ports 1 to 9 are steady on, the stack ID of the switch is 0. If the indicator is blinking, the switch is a master switch: If the indicator of a port is blinking, the number of this port is the stack ID of the switch. If the indicators of ports 1 to 9 are blinking, the stack ID of the switch is 0.

Power Supply Configuration

The S5700-28C-PWR-SI is a PoE switch. It has two power module slots, each of which can have a 500 W or 250 W power module installed. A power module can provide 369.6 W or 123.2 W of PoE power for powered devices (PDs). Table 4-467 lists its power supply configurations.

Table 4-467 Power supply configurations

Power Module 1	Power Module 2	Available PoE Power	Maximum Number of Ports (Fully Loaded)
250 W	–	123.2 W	802.3af (15.4 W per port): 8 802.3at (30 W per port): 4
500 W	–	369.6 W	802.3af (15.4 W per port): 24 802.3at (30 W per port): 12
250 W	250 W	246.4 W	802.3af (15.4 W per port): 16 802.3at (30 W per port): 8
500 W	500 W	369.6 W	802.3af (15.4 W per port): 24 802.3at (30 W per port): 12

Figure 4-176 shows the power supply mode of dual AC PoE power modules (PWR1 and PWR2). After AC power is transmitted to the PWR modules, the PWR modules provide 12 V and -53 V outputs. The outputs are combined on the motherboard, which then provides 12 V voltage for the switch and -53 V voltage for the PDs.

Figure 4-176 Power supply by dual AC PoE power modules

L: live wire

N: neutral wire

PGND: protection ground wire

GND: 12 V reference ground

RTN: -53 V reference ground

Heat Dissipation

The S5700-28C-PWR-SI uses pluggable fan modules for forced air cooling. Air flows in from the left and right sides, and exhausts from the rear panel.

Click to enlarge

This figure only shows the airflow direction and does not depict the actual device.

Technical Specifications

Table 4-468 lists technical specifications of the S5700-28C-PWR-SI.

Table 4-468 Technical specifications

Item	Description
Memory (RAM)	256 MB
Flash	32 MB
Mean time between failures (MTBF)	53.6 years when a 2-port 10GE interface card is configured, 74.6 years when a 4-port GE front card is configured, 25.68 years when a 4-port 10GE front card is configured
Mean time to repair (MTTR)	2 hours
Availability	> 0.99999
Service port surge protection	±1 kV in common mode
Power supply surge protection	±2 kV in differential mode, ±4 kV in common mode
Dimensions (H x W x D)	43.6 mm x 442.0 mm x 420.0 mm (1.72 in. x 17.4 in. x 16.5 in.)
Weight	Empty: ≤ 5 kg (11.02 lb) Fully configured: ≤ 8.5 kg (18.74 lb)
Stack ports	Two stack ports available on each stack card
RPS	Not supported
PoE	Supported
Rated voltage range	100 V AC to 240 V AC, 50/60 Hz
Maximum voltage range	90 V AC to 264 V AC, 47 Hz to 63 Hz
Maximum power consumption (100% throughput, 100% PoE loads, full speed of fans)	466 W (system power consumption: 96 W, PoE: 370 W)
Operating temperature	0°C to 50°C (32°F to 122°F)
Storage temperature	-40°C to +70°C (-40°F to +158°F)
Noise under normal temperature (27°C, sound power)	< 45 dB(A)
Relative humidity	5% to 95%, noncondensing
Operating altitude	0-5000 m (0-16404 ft.)
Certification	EMC certification Safety certification Manufacturing certification
Part number	02354137

Indicator Description

Traducción

简体中文

Descargar

Updated: 2023-04-21

N.° del documento: EDOC1000013597

Vistas:4300552

Descargas: 41265

Average rating:

This Document Applies to these Products

Related Version

Documentos relacionados

Digital Signature File

Digital Signature Authentication Mode