Version Mapping
Table 4-755 lists the mapping between the S5710-52C-EI chassis and software versions.
Table 4-755 Version mappingSeries
|
Model
|
Software Version
|
|---|
S5710-EI
|
S5710-52C-EI
|
V200R001C00 to V200R005C02
NOTE: This model does not match V200R001C01, V200R003C02, V200R003C10, or V200R005C01.
|
Appearance and Structure
Figure 4-301 S5710-52C-EI appearance![]()
1
|
Forty-eight 10/100/1000BASE-T ports
|
2
|
Four 10GE SFP+ ports
Applicable modules and cables:
|
3
|
One ETH management port
|
4
|
One mini USB port
|
5
|
One console port
|
6
|
One USB port
|
7
|
Ground screw
|
8
|
Rear card slot 1
|
9
|
Rear card slot 2
|
10
|
ESN label
NOTE: You can draw it out to view the ESN and MAC address of the switch.
|
11
|
Power module slot 2
NOTE: Applicable power modules:
|
12
|
Power module slot 1
NOTE: Applicable power modules:
|
Port Description
10/100/1000BASE-T port
A 10/100/1000BASE-T
Ethernet electrical port sends and receives service data at 10/100/1000
Mbit/s, and must use an
Ethernet cable.
Table 4-756 describes the attributes
of a 10/100/1000BASE-T Ethernet electrical port.
Table 4-756 Attributes of a 10/100/1000BASE-T Ethernet electrical port
Attribute
|
Description
|
Connector type
|
RJ45
|
Standards compliance
|
IEEE802.3, IEEE802.3u, IEEE802.3ab
|
Working mode
|
10/100/1000 Mbit/s auto-sensing
|
Maximum transmission distance
|
100 m
|
10GE SFP+ port
A 10GE SFP+ Ethernet optical port supports auto-sensing to 1000 Mbit/s. It sends and receives service data at 1000 Mbit/s or 10 Gbit/s.
Table 4-757 describes the attributes of a 10GE SFP+ Ethernet optical port.
Table 4-757 Attributes of a 10GE SFP+ portAttribute
|
Description
|
|---|
Connector type
|
LC/PC
|
Optical port attributes
|
Depend on the optical module used
|
Standards compliance
|
IEEE802.3ae
|
Working mode
|
GE/10GE auto-sensing
|
Console port
The console port is connected
to a console for on-site configuration. The port must use a
console cable. The console port is
used when a switch is powered on for the first time. For details about
the attributes of a console port, see
Table 4-758.
Table 4-758 Attributes of a console port
Attribute
|
Description
|
Connector type
|
RJ45
|
Standards compliance
|
RS-232
|
Working mode
|
Duplex Universal Asynchronous Receiver/Transmitter (UART)
|
Baud rate
|
9600 bit/s, 19200 bit/s, 38400 bit/s, 57600 bit/s, or 115200
bit/s
Default value: 9600 bit/s
|
Mini USB port
The mini USB port is connected
to a console for on-site configuration. When both the Mini USB and
console port have a cable connected, only the Mini USB port works.
ETH management port
You can connect a switch to a configuration terminal or network management workstation through the ETH management port to configure the switch locally or remotely. The port must use an
Ethernet cable. You can choose to download the software package through the ETH management port in the BootROM menu. File transfer through the ETH management port is faster than transfer through the console port. For
details on how to use the ETH management port, see the
Configuration Guide - Basic Configurations.
Table 4-759 describes the attributes of an ETH management port.
Table 4-759 Attributes of an ETH management port
Attribute
|
Description
|
Connector type
|
RJ45
|
Standards compliance
|
IEEE802.3
|
Working mode
|
10/100 Mbit/s auto-sensing
|
Maximum transmission distance
|
100 m
|
USB port
The USB port can have a USB flash drive connected to upgrade the switch, or transfer configuration files or other files. The USB port can only connect to a USB flash drive that complies with USB 2.0.
![]()
USB flash drives from different vendors differ in model compatibility and drivers. If a USB flash drive cannot be used, try to replace it with another one from a mainstream vendor. Switches support a maximum of 128 GB USB flash drives.
Indicator Description
The S5710-52C-EI has the same types of indicators as the S5710-28C-EI. For details, see Indicator Description.
Power Supply Configuration
The S5710-52C-EI uses pluggable power modules. It can be configured with a single power module or double power modules for 1+1 power redundancy. Pluggable AC and DC power modules can be used together in the same switch.
Figure 4-302 shows the power supply connections of dual DC power modules. After DC power is transmitted to the PWR module, the PWR module provides 12 V output voltage, and the motherboard provides power for the entire device.
Figure 4-302 Power supply connections of dual DC power modules![]()
NEG: negative wire
|
RTN: positive wire
|
GND: 12 V reference ground
|
Figure 4-303 shows the power supply connections of dual AC power modules. After AC power is transmitted to the PWR module, the PWR module provides 12 V output voltage, and the motherboard provides power for the entire device.
Figure 4-303 Power supply connections of dual AC power modules![]()
L: Live wire
|
N: Neutral wire
|
PGND: Protection ground wire
|
GND: 12 V reference ground
|
Heat Dissipation
The S5710-52C-EI has five built-in fans for forced air cooling. The airflow direction is left-to-right.
![]( "Click to enlarge")
![]()
This figure only shows the airflow direction and does not depict the actual device.
Technical Specifications
Table 4-760 lists technical specifications of the S5710-52C-EI.
Table 4-760 Technical specificationsItem
|
Description
|
|---|
Memory (RAM)
|
512 MB
|
Flash
|
- V200R001: 64 MB
- V200R002 and later versions: 200 MB
|
Mean time between failures (MTBF)
|
45.57 years when an 8-port GE optical card is configured, 44.85 years when an 8-port GE electrical card is configured, 43.33 years when a 2-port 10GE interface card is configured
|
Mean time to repair (MTTR)
|
2 hours
|
Availability
|
> 0.99999
|
Service port surge protection
|
Common mode: ±2 kV
|
Power supply surge protection
|
- Using AC power modules: ±6 kV in differential mode, ±6 kV in common mode
- Using DC power modules: ±1 kV in differential mode, ±2 kV in common mode
|
Dimensions (H x W x D)
|
44.4 mm x 442.0 mm x 420.0 mm (1.75 in. x 17.4 in. x 16.5 in.)
|
Weight
|
- Empty: ≤ 6 kg (13.23 lb)
- Fully configured: ≤ 10 kg (22.05 lb)
|
Stack ports
|
Four fixed 10GE SFP+ ports on the front panel or ports on the 2-port 10GE rear card
|
RPS
|
Not supported
|
PoE
|
Not supported
|
Rated voltage range
|
100 V AC to 240 V AC, 50/60 Hz
-48 V DC to -60 V DC
|
Maximum voltage range
|
90 V AC to 264 V AC, 47 Hz to 63 Hz
-36 V DC to -72 V DC
|
Maximum power consumption (100% throughput, full speed of fans)
|
146.9 W
|
Operating temperature
|
0°C to 50°C (32°F to 122°F) at an altitude of 0-1800 m (0-5906 ft.)
NOTE: When the altitude is 1800-5000 m (5906-16404 ft.), the highest operating temperature reduces by 1°C (1.8°F) every time the altitude increases by 220 m (722 ft.).
|
Storage temperature
|
-40°C to +70°C (-40°F to +158°F)
|
Noise under normal temperature (27°C, sound power)
|
< 53.9 dB(A)
|
Relative humidity
|
5% to 95%, noncondensing
|
Operating altitude
|
- AC power modules configured: 0-5000 m (0-16404 ft.)
- DC power modules configured: 0-2000 m (0-6562 ft.)
|
Certification
|
- EMC certification
- Safety certification
- Manufacturing certification
|
Part number
|
02353169
|
